GB/T 15092.101-2020Switches for appliances - Part 1-1: Requirements for mechanical switches (English PDF)

Foreword

GB/T 15092 "Appliance Switch" is divided into the following parts:

---Part 1: General requirements;

---Part 1-1: Mechanical switch requirements;

---Part 1-2: Requirements for electronic switches;

---Part 2: Special requirements;

* Special requirements for soft cord switches;

* Special requirements for conversion selector;

* Special requirements for independent installation switches;

* Special requirements for hand-held and portable power tools and garden machinery switches:

This part is Part 1-1 of GB/T 15092:

This section was drafted in accordance with the rules given in GB/T 1:1-2009:

This section uses the redrafting method to modify and adopt IEC 61058-1-1:2016 "Appliance Switch Part 1-1: Mechanical Switch Requirements":

The technical differences between this part and IEC 61058-1-1:2016 and the reasons are as follows:

---IEC 61058-1-1:2016's 14:3 stipulates: "The humidity treatment is carried out in a humid chamber, and the relative humidity of the air in the chamber is 91%~

Between 95%: In all places where the sample is placed, the air temperature is maintained at any suitable temperature (t) between 20°C and 30°C",

Considering that some areas of our country have a humid tropical climate, and all electrical and electronic products in our country use (40+/-2) degrees C for moisture resistance test,

Therefore, this part stipulates: "The humidity treatment is carried out in a humid chamber, and the relative humidity of the air in the chamber is between 91% and 95%:

In all places where the sample is placed, the air temperature should be maintained at any suitable temperature (t) between 30°C and 40°C: This requirement is consistent with

GB/T 2423:4-2008 adopts the same severity level:

---IEC 61058-1-1:2016 17:5:6 stipulates: "When required in Chapter 13, use 3 samples of different test groups for

TC10 test, instead of the sample part in the test sequence of Table 101, pass 17:6:1 (TE1) and 17:6:2 (TE2) to test", consider

Considering that 17:6:2 (TE2) is the thermal conformity assessment, which is for the complete sequence test of Chapter 14, Chapter 15, Chapter 16, and Chapter 17:

After the assessment, the TC10 test is an institutional assessment conducted using 3 samples from different test groups, and passed 17:6:1

(TE1) and 17:6:3 (TE3) are more reasonable to test, that is, functional qualification and insulation qualification are used to evaluate the test results: So the headquarters

Sub-regulations: "When required in Chapter 13, use 3 samples from different test groups for the TC10 test instead of the table 101 test:

The sample part of the test sequence is tested through 17:6:1 (TE1) and 17:6:3 (TE3)":

This section has made the following editorial changes:

---Added references:

This part was proposed by China Electrical Equipment Industry Association:

This part is under the jurisdiction of the National Electrical Accessories Standardization Technical Committee (SAC/TC67):

Drafting organizations of this section: Shanghai Electric Tool Research Institute (Group) Co:, Ltd:, Zhejiang Zhongxun Electronics Co:, Ltd:, Zhangjiagang Huajie Electronics

Co:, Ltd:, Zhejiang Jiaben Electronics Co:, Ltd:, Changzhou Yunjie Electric Co:, Ltd:, Yueqing Huiyang Electromechanical Co:, Ltd:, Zhejiang Guanbao Electronics Co:, Ltd:

Co:, Ltd:, Fa-German Electric Co:, Ltd:, Zhejiang Changlong Electric Co:, Ltd:, Southeast Electronics Co:, Ltd:, Zhongshan Yonglian Electrical Products Co:, Ltd:

The company, Zhongren Shangdong (Shanghai) Testing Technology Co:, Ltd:, Weikai Testing Technology Co:, Ltd:, Zhejiang Heling Electric Co:, Ltd:

1 Scope

Chapter 1 of GB/T 15092:1-2020 applies:

Add at the end of Chapter 1 of GB/T 15092:1-2020:

This part of GB/T 15092 applies to mechanical switching appliances and should be used in conjunction with GB/T 15092:1-2020:

Note: Additional requirements for special switches can refer to Part 2 of GB/T 15092:

2 Normative references

The following documents are indispensable for the application of this document: For dated reference documents, only the dated version applies to this document.

Pieces: For undated references, the latest version (including all amendments) applies to this document:

Chapter 2 of GB/T 15092:1-2020 applies:

3 Terms and definitions

Chapter 3 of GB/T 15092:1-2020 applies:

4 General requirements

Chapter 4 of GB/T 15092:1-2020 applies:

5 General considerations for the test

After adding the following requirements, GB/T 15092:1-2020 Chapter 5 applies:

Added at the end of 5:4:

Table 101 provides precautions for the following aspects:

---The minimum number of samples required for each test;

--- When adding appropriate tests, the minimum number of total samples required for each evaluation;

---Additional samples required due to increased electrical ratings, specific structures, or damage or rupture during the test:

Table 101 Test samples

Article number entry minimum number of each test sample a Remarks

5 General precautions for the test-iib

6 Rating

7 categories

8 Signs and documents

1 c