GB/T 11313.13-2018Radio-frequency connectors -- Part 13: Sectional specification for type 1.6/5.6 and 1.8/5.6 RF coaxial connectors (English PDF)

Foreword

GB/T 11313 "RF Connector" has or plans to release the following parts.

--- Part 1. General requirements and test methods;

--- Part 2. Section 9.52 RF coaxial connector sub-specification;

--- Part 3. Double-pin connector for double-balanced antenna feeders.

--- Part 4. External conductor with inner diameter of 16mm (0.63in), characteristic impedance of 50ohm, screw-connected RF coaxial connector

(Type 7-16);

--- Part 5. Partial specification for RF coaxial connectors for mating with 60096 IEC 50-17 and larger cables;

--- Part 6. Partial specification for RF coaxial connectors for mating with 60096 IEC 75-17 and larger cables;

--- Part 7. RF coaxial connector with outer conductor inner diameter of 9.5mm (0.374in), characteristic impedance of 50ohm, bayonet connection

(Type C) sub-specification;

--- Part 8. RF coaxial connection with outer conductor inner diameter of 6.5mm (0.256in), characteristic impedance of 50ohm (75ohm), bayonet connection

Connector (BNC type) sub-specification;

---Part 9. SMC series RF coaxial connector sub-specification;

--- Part 10. SMB series RF coaxial connector sub-specification;

--- Part 11. RF coaxial connector with outer conductor inner diameter 9.5mm (0.374in), characteristic impedance 50ohm, threaded connection

(4.1/9.5 type) sub-specification;

--- Part 12. Non-matching threaded connection RF coaxial connector (UHF type) sub-specification;

--- Part 13. Sectional specification for 1.6/5.6 and 1.8/5.6 RF coaxial connectors;

--- Part 14. External conductor inner diameter 12mm (0.472in), characteristic impedance 75ohm, threaded RF coaxial connector

(3.5/12 type) sub-specification;

--- Part 15. RF coaxial connector with outer conductor inner diameter of 4.13mm (0.163in), characteristic impedance of 50ohm, threaded connection

(SMA type);

--- Part 16. External conductor with inner diameter of 7mm (0.276in), characteristic impedance of 50ohm (75ohm), threaded RF coaxial connection

Connector (N type) sub-specification;

--- Part 17. RF coaxial connectors with outer conductor inner diameter 6.5mm (0.256in), characteristic impedance 50ohm, threaded connection

(TNC type) sub-specification;

--- Part 18. SSMA series RF coaxial connector sub-specification;

--- Part 19. SSMB type RF coaxial connector sub-specification;

--- Part 20. RF coaxial connector with outer conductor inner diameter of 2.08mm (0.082in), characteristic impedance of 50ohm, threaded connection

(SSMC type) sub-specification;

--- Part 21. The outer conductor has an inner diameter of 9.5 mm (0.374 in) and a characteristic impedance of 50 ohm. It has two different threaded connections.

RF connector (SC-A and SC-B type) sub-specification;

--- Part 22. Double-core RF connectors (BNO type) with double-conductor shielded symmetrical cables for bayonet connection;

--- Part 23. Connect 3.5mm hard precision coaxial cable, outer conductor inner diameter of 3.5mm (0.1378in) RF coaxial connector

specification;

--- Part 24. 75ohm cable distribution system with threaded RF coaxial connector (F type) sub-specification;

---Part 25. Double-core threaded type with double inner conductor shielded symmetrical cable and outer conductor inner diameter of 13.56mm (0.534in) (3/4-

20UNEF) connection connector (TWHN type) sub-specification;

--- Part 26. TNCA series RF coaxial connector sub-specification;

--- Part 27. 75ohm cable distribution system with threaded connection RF coaxial connector (E type) sub-specification;

--- Part 28. outer conductor inner diameter is 5.60mm (0.220in), characteristic impedance is 75ohm, card lock connection RF coaxial connector

specification;

--- Part 29. 50ohm and 75ohm with a characteristic impedance of 50ohm, with threaded, push-pull, quick-lock or slide-type rack or panel

Type RF coaxial connector (1.0/2.3 type) sub-specification;

--- Part 31. RF coaxial connector with outer conductor inner diameter 1.0mm (0.039in), characteristic impedance 50ohm, threaded connection

(type 1.0) sub-specification;

--- Part 32. RF coaxial connector with outer conductor inner diameter of 1.85mm (0.072in), characteristic impedance of 50ohm, threaded connection

(1.85 type) sub-specification;

--- Part 33. BMA series RF connector sub-specification;

--- Part 35. 2.92 series RF connector sub-specification;

---Part 36. Snap-on connection micro-miniature RF coaxial connectors with characteristic impedance of 50 ohm (MCX type);

--- Part 37. STWX8 series RF coaxial connector sub-specification;

--- Part 38. Module slide-in RF connectors (TMA type) for 50 ohm backplanes and panels;

--- Part 39. CQM series fast locking RF connector sub-specification;

--- Part 40. 2.4 series RF connector sub-specification;

--- Part 41. CQA series fast locking RF connector sub-specification;

--- Part 42. CQN series fast locking RF connector sub-specification;

--- Part 43. RBMA series blind matching RF coaxial connector sub-specification;

--- Part 44. SMP series push-in RF coaxial connector sub-specification;

--- Part 45. SQMA series fast locking RF coaxial connector sub-specification;

--- Part 47. Fquick series 75ohm cable distribution system with plug-in RF coaxial connector sub-specification;

--- Part 48. BMP series blind matching RF coaxial connector sub-specification;

--- Part 49. SMAA series RF coaxial connector sub-specification;

--- Part 50. Inner conductor inner diameter is 4.11mm, characteristic impedance is 50ohm, fast locking RF coaxial connector (QMA type)

Sub-specification

--- Part 51. outer conductor inner diameter of 13.5mm, characteristic impedance of 50ohm, bayonet locking RF coaxial connector (QLI type)

specification;

--- Part 53. S7-16 series threaded RF coaxial connector sub-specification;

--- Part 54. The outer conductor has an inner diameter of 10mm, and the characteristic impedance is 50ohm RF coaxial connector (4.3-10 series) sub-specification;

--- Part 58. SBMA series blind matching RF coaxial connector sub-specification;

--- Part 59. L32-4 and L32-5 type threaded multi-channel RF connector sub-specification;

--- Part 101. MMCX series RF coaxial connector sub-specification;

--- Part.201. Electrical test method reflection coefficient and voltage standing wave ratio;

--- Part 202. Electrical test method insertion loss.

This part is the 13th part of GB/T 11313.

This part is drafted in accordance with the rules given in GB/T 1.1-2009.

This section uses the redrafting method with reference to IEC 60169-13.1976 "RF Connectors Part 13. Outer conductor inner diameter 5.6mm

(0.22in), nominal impedance of 75ohm (1.6/5.6 type) and 50ohm (1.8/5.6 type), RF coaxial connector with smaller plug size"

(including Amendment 1.1996), the degree of conformity with IEC 60169-13.1976 (including Amendment 1.1996) is non-equivalent.

The main differences between this part and IEC 60169-13.1976 (including Amendment 1.1996) are as follows.

--- Standardize the statement of statements in the scope of Chapter 1;

--- Added Chapter 2 normative references;

--- "Rated" "climate category" and "type test list" unified Chapter 4 quality assessment procedures;

--- Removed "IEC Model Name" "Structure Review" "Dimensions";

--- Re-drawing the drawings according to the new drawing and dimensioning requirements (see 3.1.1, 3.1.2, 3.1.3, 3.2.1, 3.2.2);

--- IEC 60169-13. 1976 in Figure 2 increased size "f" maximum of 0.1;

--- IEC 60169-13. 1976 is uniformly described as "push-pull stop" and "slide-rail";

--- IEC 60169-13. 1976 Figure 3b increased size "y" minimum of 3.00;

--- IEC 60169-13. 1976 Figure 4a leak size "p", and size "n" "r" and "p" unified to Figure 2, the relevant size

One to Table 2;

--- IEC 60169-13. 1976 Figure 4b increased size "phip" minimum of 7.20 and "q" of 3.15 ~ 3.30;

--- IEC 60169-13. 1976 Figure 5b increased size "r" maximum of 1.80;

--- IEC 60169-13. 1976 Figure 6 optimized size "p" changed from 6.600 ~ 6.609 to 6.595 ~ 6.600;

--- IEC 60169-13.1976 Figure 7 optimized size "q" changed from 1.026~1.030 and 0.966~0.970 to 1.030~1.035

And 0.965~0.970; the optimized size "b" is changed from 5.00~5.10 to 5.50~6.00;

--- Thread M9 x 0.5 increased accuracy requirements, the external thread is "M9 x 0.5-6g", the internal thread is "M9 x 0.5-6H";

--- For 3.2.1.1 "test procedures" and 3.2.2.1 "test procedures" slightly adjusted according to the latest national standard format;

--- Improve the shielding efficiency of 1.6/5.6 type (75ohm) RF coaxial connector. Threaded connector >=90dB at 1GHz~3GHz;

The push-pull stop connector is >=80dB at 1GHz~3GHz; the slide rail connector is >=80dB at 1GHz~3GHz;

--- Improve the frequency range of the 1.8/5.6 (50ohm) RF coaxial connector to 10GHz, reflection coefficient. Straight connector <= 0.20,

Right angle bend connector <=0.30; shielding efficiency. Threaded connector >=90dB at 1GHz~3GHz; push-pull stop type

The connector is >=80dB at 1GHz~3GHz; the slider connector is >=80dB at 1GHz~3GHz;

--- "Rating value and characteristics" in the cable type; the contact resistance of the center piece contact is changed to the initial value <= 3.0mohm, after the environmental test

<=5.0mohm; push-pull stop separation force is changed to 18Nmin, 50Nmax;

--- For the contents of Chapter 4, slightly adjusted according to the latest national standard format;

--- For the content of Chapter 5 and the blank detailed specification format have been standardized.

1 Scope

This part is the sub-specification of GB/T 11313.1-2013, which gives the development of 1.6/5.6 type (75ohm) and 1.8/5.6 type (50ohm) shots.

The content and rules of the detailed specification of the frequency coaxial connector, as well as the blank format of the detailed specification. Type 1.6/5.6 (75ohm) and Type 1.8/5.6

The (50 ohm) RF coaxial connector has a threaded and push-pull stop connection and a mechanism for use with slide rails and panels.

The 1.6/5.6 type (75ohm) cable connector can work normally in the frequency range up to 1GHz, and the 1.8/5.6 type (50ohm) cable connector

It can work normally in the range of 10GHz, and can be used in microwave transmission systems (with various RF cables or microstrips).

This section specifies the size of the mating interface of the 2-level universal connector, the standard gauge detection requirements, and from GB/T 11313.1-2013

Detailed specifications for all detailed specifications for the 1.6/5.6 (75ohm) and 1.8/5.6 (50ohm) RF coaxial connectors

And test procedures.

This section also specifies recommended ratings and characteristics to be considered when preparing detailed specifications, and specifies the applicable ratings for Class M and Class H.

Level test schedule and inspection requirements.

Note. The original dimensions of this section are in millimeters, and all unsized dimensions are for reference only.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article.

Pieces. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 11313.1-2013. Part 1 . General specification general requirements and test methods (IEC 61169-1.

1998, IDT)

Passive radio frequency and microwave devices - Intermodulation level measurement - Part 3. Passive intermodulation measurement for coaxial connectors

(PassiveRFandmicrowavedevices,intermodulationlevelmeasurement-Part 3.Measurementofpas-

Siveintermodulationincoaxialconnectors)

3 mating interface and standard gauge