GB/T 11313.11-2018Radio-frequency connectors -- Part 11: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9.5 mm (0.374 in) with screw coupling with characteristic impedance 50 ohm (type 4.1/9.5) (English PDF)

Foreword

GB/T 11313 "RF Connector" has or plans to release the following parts.

--- Part 1. General requirements and test methods;

--- Part 2. Section 9.52 RF coaxial connector sub-specification;

--- Part 3. Double-pin connector for double-balanced antenna feeders.

--- Part 4. External conductor with inner diameter of 16mm (0.63in), characteristic impedance of 50ohm, screw-connected RF coaxial connector

(Type 7-16);

--- Part 5. Partial specification for RF coaxial connectors for mating with 60096 IEC 50-17 and larger cables;

--- Part 6. Partial specification for RF coaxial connectors for mating with 60096 IEC 75-17 and larger cables;

--- Part 7. RF coaxial connector with outer conductor inner diameter of 9.5mm (0.374in), characteristic impedance of 50ohm, bayonet connection

(Type C) sub-specification;

--- Part 8. RF coaxial connection with outer conductor inner diameter of 6.5mm (0.256in), characteristic impedance of 50ohm (75ohm), bayonet connection

Connector (BNC type) sub-specification;

---Part 9. SMC series RF coaxial connector sub-specification;

--- Part 10. SMB series RF coaxial connector sub-specification;

--- Part 11. RF coaxial connector with outer conductor inner diameter 9.5mm (0.374in), characteristic impedance 50ohm, threaded connection

(4.1/9.5 type) sub-specification;

--- Part 12. Non-matching threaded connection RF coaxial connector (UHF type) sub-specification;

--- Part 13. Sectional specification for 1.6/5.6 and 1.8/5.6 RF coaxial connectors;

--- Part 14. External conductor inner diameter 12mm (0.472in), characteristic impedance 75ohm, threaded RF coaxial connector

(3.5/12 type) sub-specification;

--- Part 15. RF coaxial connector with outer conductor inner diameter of 4.13mm (0.163in), characteristic impedance of 50ohm, threaded connection

(SMA type);

--- Part 16. External conductor with inner diameter of 7mm (0.276in), characteristic impedance of 50ohm (75ohm), threaded RF coaxial connection

Connector (N type) sub-specification;

--- Part 17. RF coaxial connectors with outer conductor inner diameter 6.5mm (0.256in), characteristic impedance 50ohm, threaded connection

(TNC type) sub-specification;

--- Part 18. SSMA series RF coaxial connector sub-specification;

--- Part 19. SSMB type RF coaxial connector sub-specification;

--- Part 20. RF coaxial connector with outer conductor inner diameter of 2.08mm (0.082in), characteristic impedance of 50ohm, threaded connection

(SSMC type) sub-specification;

--- Part 21. The outer conductor has an inner diameter of 9.5 mm (0.374 in) and a characteristic impedance of 50 ohm. It has two different threaded connections.

RF connector (SC-A and SC-B type) sub-specification;

--- Part 22. Double-core RF connectors (BNO type) with double-conductor shielded symmetrical cables for bayonet connection;

--- Part 23. Connect 3.5mm hard precision coaxial cable, outer conductor inner diameter of 3.5mm (0.1378in) RF coaxial connector

specification;

--- Part 24. 75ohm cable distribution system with threaded RF coaxial connector (F type) sub-specification;

---Part 25. Double-core threaded type with double inner conductor shielded symmetrical cable and outer conductor inner diameter of 13.56mm (0.534in) (3/4-

20UNEF) connection connector (TWHN type) sub-specification;

--- Part 26. TNCA series RF coaxial connector sub-specification;

--- Part 27. 75ohm cable distribution system with threaded connection RF coaxial connector (E type) sub-specification;

--- Part 28. outer conductor inner diameter is 5.60mm (0.220in), characteristic impedance is 75ohm, card lock connection RF coaxial connector

specification;

--- Part 29. 50ohm and 75ohm with a characteristic impedance of 50ohm, with threaded, push-pull, quick-lock or slide-type rack or panel

Type RF coaxial connector (1.0/2.3 type) sub-specification;

--- Part 31. RF coaxial connector with outer conductor inner diameter 1.0mm (0.039in), characteristic impedance 50ohm, threaded connection

(type 1.0) sub-specification;

--- Part 32. RF coaxial connector with outer conductor inner diameter of 1.85mm (0.072in), characteristic impedance of 50ohm, threaded connection

(1.85 type) sub-specification;

--- Part 33. BMA series RF connector sub-specification;

--- Part 35. 2.92 series RF connector sub-specification;

---Part 36. Snap-on connection micro-miniature RF coaxial connectors with characteristic impedance of 50 ohm (MCX type);

--- Part 37. STWX8 series RF coaxial connector sub-specification;

--- Part 38. Module slide-in RF connectors (TMA type) for 50 ohm backplanes and panels;

--- Part 39. CQM series fast locking RF connector sub-specification;

--- Part 40. 2.4 series RF connector sub-specification;

--- Part 41. CQA series fast locking RF connector sub-specification;

--- Part 42. CQN series fast locking RF connector sub-specification;

--- Part 43. RBMA series blind matching RF coaxial connector sub-specification;

--- Part 44. SMP series push-in RF coaxial connector sub-specification;

--- Part 45. SQMA series fast locking RF coaxial connector sub-specification;

--- Part 47. Fquick series 75ohm cable distribution system with plug-in RF coaxial connector sub-specification;

--- Part 48. BMP series blind matching RF coaxial connector sub-specification;

--- Part 49. SMAA series RF coaxial connector sub-specification;

--- Part 50. Inner conductor inner diameter is 4.11mm, characteristic impedance is 50ohm, fast locking RF coaxial connector (QMA type)

Sub-specification

--- Part 51. outer conductor inner diameter of 13.5mm, characteristic impedance of 50ohm, bayonet locking RF coaxial connector (QLI type)

specification;

--- Part 53. S7-16 series threaded RF coaxial connector sub-specification;

--- Part 54. The outer conductor has an inner diameter of 10mm, and the characteristic impedance is 50ohm RF coaxial connector (4.3-10 series) sub-specification;

--- Part 58. SBMA series blind matching RF coaxial connector sub-specification;

--- Part 59. L32-4 and L32-5 type threaded multi-channel RF connector sub-specification;

--- Part 101. MMCX series RF coaxial connector sub-specification;

--- Part.201. Electrical test method reflection coefficient and voltage standing wave ratio;

--- Part 202. Electrical test method insertion loss.

This part is the 11th part of GB/T 11313.

This part is drafted in accordance with the rules given in GB/T 1.1-2009.

This section uses the redrafting method with reference to IEC 60169-11.1977 "RF Connectors Part 11. Outer conductor inner diameter 9.5mm

(0.374in) Threaded RF coaxial connector with characteristic impedance of 50ohm (4.1/9.5 type), compiled with IEC 60169-11.1977

The degree of sex is not equivalent.

The main differences between this part and IEC 60169-11.1977 are as follows.

--- The "1 Scope" of this section has been adapted in the format of the sub-specification;

--- Added "2 normative references";

--- All the figures in this section have been redrawn according to China's drawing standards (see 3.1.1, 3.1.2, 3.2.1, 3.3.1, 3.3.2);

--- Thread M20 x 1 increased accuracy requirements, the external thread is "M20 x 1-6g", the internal thread is "M20 x 1-6H";

--- Change the size "e" of Figure 1 in IEC 60169-11.1977 from 9.4~9.6 to 9.45~9.55;

--- Change the size "g" of Figure 1 in IEC 60169-11.1977 from 0.8~1.6 to 1.4~1.6;

--- Change the size "i" of Figure 1 in IEC 60169-11.1977 from 2.0~4.0 to 3.0~4.0;

--- This section adds dimensions "l" and "m" to Figure 1 of IEC 60169-11.1977;

--- Change the size "e" of Figure 2 in IEC 60169-11.1977 from 9.4~9.6 to 9.45~9.55;

--- Change the size "q" of Figure 2 in IEC 60169-11.1977 from 5.8~6.2 to size "h" 6.05~6.20;

--- This section adds dimensions "c", "i", "l" and "n" to Figure 2 of IEC 60169-11.1977;

---Standard test connector (level 0) increases the geometric tolerance requirements;

--- Removed the "2IEC Model Nomenclature", "7 Structure Overview" and "8 Dimensions" in IEC 60169-11.1977;

---Incorporate the "4 preferred climate categories" in IEC 60169-11.1977 into the environmental aspects of "Standards and characteristics of Table 6" in this section.

Capable part

--- In the IEC 60169-11.1977 "3 rating" and "9 type test list" are included in this section "4 quality assessment

program";

--- "Table 6 Ratings and Characteristics" increases the requirements for rated power and passive intermodulation;

--- Added "5 detailed specification development guide".

1 Scope

This part is the sub-specification of GB/T 11313.1-2013, which gives the detailed specification for the development of the 4.1/9.5 type RF coaxial connector.

The tolerances and rules, as well as the blank format of the detailed specification. 4.1/9.5 RF coaxial connector with 50ohm nominal impedance, threaded connection, working

The frequency is up to 14GHz, which is mainly used to match various RF cables or microstrips in the microwave transmission system.

This section specifies the size of the mating interface of the 2-level universal connector, the detailed dimensions of the 0-level standard test connector, and the standard gauge test.

Requirements and standard specifications for all detailed specifications of the 4.1/9.5 RF coaxial connectors selected from GB/T 11313.1-2013

Detailed requirements and test procedures.

This section also specifies recommended ratings and characteristics to be considered when preparing detailed specifications, and specifies the applicable ratings for Class M and Class H.

Level test schedule and inspection requirements.

Note. The original dimensions of this section are in millimeters, and all unsized dimensions are for reference only.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article.

Pieces. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 11313.1-2013. Part 1 . General specification general requirements and test methods (IEC 61169-1.

1998, IDT)

IEC 61726 Cable Assemblies, Cables, Connectors and Passive Microwave Components Shielding Attenuation Measurement Reverberation Chamber Method (Cableassemblies,

Cables,connectorsandpassivemicrowavecomponents-Screeningattenuationmeasurementbythere-

Verberationchambermethod)

Passive radio frequency and microwave devices - Intermodulation level measurement - Part 3. Passive intermodulation measurement for coaxial connectors

(PassiveRFandmicrowavedevices,intermodulationlevelmeasurement-Part 3.Measurementof

Passiveintermodulationincoaxialconnectors)

IEC 62153-4 Metallic Communication Cable Test Method Part 4 (Metaliccommunicationcabletestmethods-

Part 4)

3 mating interface and standard gauge