CJ/T 217-2013Compound quick air inbreathe-release valve for water supply pipeline (English PDF)
给水管道复合式高速进排气阀
This is a limited preview
Buy now to download the full PDF (27 pages)
Need quotation for your management?
Get a formal quotation for CJ/T 217-2013 in 30 minutes.
Issued by
Ministry of Housing and Urban-Rural Development of the People's Republic of China
Level / Type
National · Recommended
Issue date
April 27, 2013
Implementation date
October 1, 2013
Scope
CJ/T 217-2013 is the English-translated version of 给水管道复合式高速进排气阀.
CJ/T 217-2013 is the Chinese standard "Compound quick air inbreathe-release valve for water supply pipeline".
Its scope clause reads: This Standard specifies the term and definition, structure style, product model, materials, requirements, test methods, inspection rules, marks, product specification, product packaging, storage and transportation of compound quick air inbreathe-release valve for water supply pipeline (hereinafter referred to as air inbreathe-release valve).
The Standard applies to the air inbreathe-release valve of nominal size of DN15~DN300, nominal pressure of not more than PN25, and water temperature of 0°C~40°C for water supply pipeline. Its clauses include terms and definitions.
Found what you need?
Document preview — CJ/T 217-2013
National Standard of the People's Republic of China
- ICS
- 91.140.01
- Classification
- P 41
Issued by: Ministry of Housing and Urban-Rural Development of the People's Republic of China
Contents
- Foreword3
- 1 Scope5
- 2 Normative references5
- 3 Terms and definitions6
- 4 Structural type7
- 5 Product model8
- 6 Materials8
- 7 Requirements8
- 8 Test methods11
- 9 Inspection rules13
- 10 Mark and product instructions15
- 11 Packing, storage and transportation15
- Appendix A16
- Appendix B18
- Appendix C20
- Appendix D21
- Appendix E26
- Appendix F27
1 Scope
This Standard specifies the term and definition, structure style, product model, materials, requirements, test methods, inspection rules, marks, product specification, product packaging, storage and transportation of compound quick air inbreathe-release valve for water supply pipeline (hereinafter referred to as air inbreathe-release valve).
The Standard applies to the air inbreathe-release valve of nominal size of DN15~DN300, nominal pressure of not more than PN25, and water temperature of 0°C~40°C for water supply pipeline.
2 Normative references
The articles contained in the following documents become part of this standard when they are quoted herein. For the dated documents so quoted, only the dated versions apply to this document. For undated reference documents, the latest versions (including all corrections) apply to this Standard.
GB/T 196 General purpose metric screw threads - Basic dimensions
GB/T 197 General purpose metric screw threads - Tolerances
GB/T 700 Carbon structural steels
GB/T 1047 Pipework components--Definition and selection of DN(nominal size)
GB/T 1048 Pipework components--Definition and selection of PN GB/T 3098 (All parts) Mechanical properties of fasteners
GB/T 3280 Cold rolled stainless steel plate sheet and strip
GB/T 6739-2006 Paints and varnishes - Determination of film hardness by pencil test
GB/T 7306.2 Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads--Part 2. Taper internal and external threads
GB/T 8923-2008 Preparation of steel substrates before application of paints and related products
GB/T 9286-1998 Paints and varnishes-Cross cut test for films
GB/T 9969 General principles for preparation of instructions for use of industrial products
GB/T 12220 General purpose industrial valves-Marking
GB/T 12225 General purpose industrial valves- Specification of copper alloy castings
GB/T 12227 General purpose industrial valve - Specification of spheroidal graphite iron castings
GB/T 13927 Industrial valves - Pressure testing
GB/T 17241.6 Integral cast iron pipe flanges
GB/T 17241.7 Specifications for cast iron pipe flanges
GB/T 21873 Rubber seals - Joint rings for water supply drainage and sewerage pipelines - Specification for materials
JB/T 308 Valves model designation method
JB/T 7928 General purpose industrial valve - Delivery specification
3 Terms and definitions
For the purpose of this standard, the following terms and definitions shall apply.
3.1 Compound quick air inbreathe-release valve for water supply pipeline
The air intake and exhaust device equipped with large and small intake and exhausted holes. It can quickly exhaust the air when the pipeline is filled by water. It can quickly intake the air when negative pressure is generated in the pipeline. It can discharge the small amount of air gathered in pipeline under the normal working state. It can automatically close the valve after exhaust.
3.2 Exhaust volume
The gas volume exhausted outward by air inbreathe-release valve, in unit of time.
3.3 Pressure differential of inlet and outlet when closed by drained air
When air inbreathe-release valve exhausts large amount of gas, the floating body will block the large intake and exhausted hole. It causes the difference between valve inlet pressure and outlet pressure when the air inbreathe-release valve is closed.
3.4 Inlet pressure of air release valve
The sum of static pressure at the pressure-measuring section of air inbreathe-release valve inlet AND the gas kinetic energy of unit volume.
3.5
Pressure diffe...
GB/T 18916.3-2022 | GB/T 18916.31-2017 | CJJ/T 210-2014 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 27 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 196General purpose metric screw threads - Basic dimensions
- GB/T 197General purpose metric screw threads -- Tolerances
- GB/T 700Carbon structural steels
- GB/T 1047Pipework components - Definition and selection of nominal size
- GB/T 1048Pipework components - Definition and selection of nominal pressure
- GB/T 3280Cold rolled stainless steel plate, sheet and strip
GB/T 3098
How to Download CJ/T 217-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 1047-1995 — Nominal size for pipe components
GB/T 1047-2005 — Pipework components - Definition and selection of DN (nominal size)
GB/T 1047-2019 — Pipework components - Definition and selection of nominal size
CJ/T 217-2013
$125.00