Valid

YY/T 0652-2016Wear of implant materials—Polymer and metal wear particles—Isolation and characterization (English PDF)

植入物材料的磨损聚合物和金属材料磨屑分离和表征

Preview PDF

This is a limited preview

Buy now to download the full PDF (23 pages)

Need quotation for your management?

Get a formal quotation for YY/T 0652-2016 in 30 minutes.

Issued by

NMPA

Level / Type

Industry · Recommended

Issue date

January 26, 2016

Implementation date

January 1, 2017

Scope

YY/T 0652-2016 is the English-translated version of 植入物材料的磨损聚合物和金属材料磨屑分离和表征.

YY/T 0652-2016 is the Chinese pharmaceutical industry standard that gives the methods for sampling, separating and characterising the wear debris produced by an implant, whether recovered from tissue taken at revision surgery or at autopsy or from the lubricant of a joint simulator.

It sets out the reagents and the digestion of the tissue, the isolation of polymer and metal particles, and their characterisation by number, size and shape, with some steps applicable to debris in body fluids such as joint aspirate. Issued on 26 January 2016, it has applied since 1 January 2017.

Found what you need?

Document preview — YY/T 0652-2016

National Standard of the People's Republic of China

ICS
11.040.40
Classification
C 35
Replacing
YY/T 0652-2008

Issued by: National Medical Products Administration of the People's Republic of China

Contents

  • Preface
  • Introduction
  • 1 Scope
  • 2 terms and definitions Sampling and analysis of polymer debris and metal debris in tissue samples
  • 5 Joint simulator Sampling and analysis of polymer and metal abrasive in lubricating fluid
  • 6 Test Report

Foreword

This standard is drafted in accordance with the rules given in GB/T 1.1-2009.

This standard replaces YY/T 0652-2008 "Wear of polymer materials and metal materials Debris separation, characterization and quantification Analysis method ", compared with YY/T 0652-2008, the main technical changes are as follows.

--- increase the processing steps of 5.4 ceramic debris;

--- removed the original standard 3.9 control test and 3.10 particle number calculation.

This standard uses the translation method equivalent to ISO 17853.:2011 "Wearing materials for wear materials and metal materials.

And characterization ". For ease of use, this standard has been modified as follows.

--- the standard concentration of the unit M with mol/L instead, M does not belong to GB 3101 and GB 3102 parts given by the unit.

Introduction

The biological reaction of the debris can lead to bone resorption and prosthesis loosening, resulting in failure of the joint implant. To characterize the debris, There must be a uniform method of extracting debris from the tissue to ensure a uniform standard for evaluating the impact of debris. On the implant simulator The resulting debris speculation also provides valuable information for the wear properties and performance of the implant under study.

In this standard, the first method of separating and characterizing debris in the tissue or in the simulator lubricating fluid is to filter or embed the resin (LC) or transmission electron microscopy (TEM) were used to analyze the debris. The results were analyzed by scanning electron microscopy (SEM) or transmission electron microscopy (TEM). Correct Another method of separation and characterization of the implanted metal debris in the simulator has recently been developed in which debris can be deposited on the wafer SEM analysis, without filtering or mosaic [1]. At the time of publication of this standard, the second method has not been used to separate and characterize debris in the tissue, The results obtained by the two methods are not directly compared. Therefore, the latter is not listed in detail.

1 Scope

This standard specifies the sampling methods for debris produced by implantation of the implant in the human body and in the simulator. This standard specifies separation And characterization of polymer and metal debris (debris from the revision surgery or autopsy of the joint replacement of the implant around the excision of the tissue or joint simulation Lubricating fluid), reagents and test methods. Some of these steps can be applied to the separation and characterization of debris in human body fluids (eg joints Synovial fluid).

There is no quantification of the degree of wear generated by the implant in this standard; nor does it specify the amount of wear required for any particular surface. This standard does not Including the biological reactions of debris, and the methods used to assess biosafety.

2 Terms and definitions

The following terms and definitions apply to this document.

2.1 Polymer wear

The polymer parts of the implant are worn out by the particles.

2.2 Metal scraping metalwearparticle

The metal parts of the implant are worn out by particles and granular corrosion products.

2.3 Ceramic wear

The ceramic parts of the implant are worn out by the particles.

3 Principle, reagents and instruments

3.1 Principles

Polymer debris and metal debris by digestion tissue samples and simulator lubricating fluid separation, and then by removing other organic debris Purified to get.

Note. The method of separating polymer debris and metal debris is different and will be described separately in 4.2 and 4.3.

The debris was collected and characterized and counted by scanning electron microscopy (SEM) or transmission electron microscopy (TEM) (if applicable).

3.2 Reagents

During the analysis, unless otherwise stated, only approved analytical reagents, distilled water or water of the same purity grade are used.

To avoid contamination of the sample with foreign particles, all reagent solutions should be filtered using a filter with a pore size of 0.2 µm or less before use.

3.2.2 Acetone

100% or diluted with distilled water to 80%.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.

Similar standards

Editions of YY/T 0652

EditionTitleRevisionStatus
YY/T 0652-2016Wear of implant materials—Polymer and metal wear particles—Isolation and characterizationcurrent editionCurrent
YY/T 0652-2008Wear of implant materials—Polymer and metal wear particles—Isolation and characterizationprevious editionSuperseded

This page sells the current edition, YY/T 0652-2016. Earlier editions are listed for reference only.

How to Download YY/T 0652-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
23 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

YY/T 0652-2016

$235.00