Valid

YY 0118-2005Hip joint prostheses (English PDF)

髋关节假体

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for YY 0118-2005 in 30 minutes.

Issued by

NMPA

Level / Type

Industry · Mandatory

Issue date

December 7, 2005

Implementation date

December 1, 2006

Scope

YY 0118-2005 is the English-translated version of 髋关节假体.

YY 0118-2005 is the Chinese standard "Hip joint prostheses". Its scope clause reads: This standard specifies the definitions, classification, requirements, test methods, inspection rules, marking, packaging, instructions for use, transportation, storage and the like of total and partial hip joint replacements.

This standard is applicable to the joint prostheses used for the total and partial hip joint replacement of human body. Its clauses include terms, definitions and classification.

Found what you need?

Document preview — YY 0118-2005

National Standard of the People's Republic of China

Replacing
YY 0118-1993

Issued by: National Medical Products Administration of the People's Republic of China

Contents

  • Foreword II
  • 1 Scope
  • 2 Normative References
  • 3 Terms, Definitions and Classification
  • 4 Requirements
  • 5 Test Methods
  • 6 Inspection Rules
  • 7 Instructions for Use
  • 8 Marking
  • 9 Packaging
  • 10 Transportation and Storage
  • Appendix A (Normative) List of Material Standards Found Acceptable for the Manufacture of Hip Joint Prostheses
  • Bibliography

1 Scope

This standard specifies the definitions, classification, requirements, test methods, inspection rules, marking, packaging, instructions for use, transportation, storage and the like of total and partial hip joint replacements.

This standard is applicable to the joint prostheses used for the total and partial hip joint replacement of human body.

2 Normative References

The following standards contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.

GB/T 2828.1 Sampling Procedures for Inspection by Attributes - Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection (GB/T 2828.1-2003, ISO 2859-1, IDT)

GB/T 2829 Sampling Procedures and Tables for Periodic Inspection by Attributes (Apply to Inspection of Process Stability)

GB/T 14233.1 Test Methods for Infusion, Transfusion, Injection Equipments for Medical Use - Part 1: Chemical Analysis Methods

GB/T 14233.2 Test Methods for Infusion, Transfusion, Injection Equipment for Medical Use - Part 2: Biological Test Methods

GB/T 16886.7 Biological Evaluation of Medical Devices - Part 7: Ethylene Oxide Sterilization Residuals (GB/T 16886.7-2001, idt ISO 10993-7: 1995)

GB/T 19701.2 Implants for Surgery Ultra-high Molecular Weight Polyethylene - Part 2: Moulded Forms (GB/T 19701.2-2005, ISO 5834-2: 1998, IDT)

YY 0117 (All the parts) Implants for Surgery - Forgings, Castings for Bone Joint Prostheses

YY 0341 General Technological Requirements for Non-active Metallic Surgery Implants of Osteosynthesis

YY/T 0343 Liquid Penetrant Inspection of Metallic Surgical Implants (YY/T 0343-2002, ISO 9583: 1993, NEQ)

ISO 6474 Implants for Surgery - Ceramic Materials Based on High Purity Alumina

ISO 7206-1 Implants for Surgery - Partial and Total Hip Joint Prostheses - Part 1: Classification and Designation of Dimensions

ISO 7206-2 Implants for Surgery - Partial and Total Hip Joint Prostheses - Part 2: Articulating Surfaces Made of Metallic, Ceramic and Plastics Materials

ISO 7206-4 Implants for Surgery - Partial and Total Hip Joint Prostheses - Part 4: Determination of Endurance Properties and Performance of Stemmed Femoral Components

ISO 7206-6 Implants for Surgery - Partial and Total Hip Joint Prostheses - Part 6: Endurance Properties Testing and Performance Requirements of Neck Region of Stemmed Femoral Components

ISO 7206-8 Implants for Surgery - Partial and Total Hip Joint Prostheses - Part 8: Endurance Performance of Stemmed Femoral Components with Application of Torsion

ISO 13356 Implants for Surgery - Ceramic Materials Based on Yttria-stabilized Tetragonal Zirconia (Y-TZP)

ISO 13779-2 Implants for Surgery - Hydroxyapatite - Part 2: Coatings of Hydroxyapatite

ISO 14242-1 Implants for Surgery - Wear of Total Hip-joint Prostheses - Part 1: Loading and Displacement Parameters for Wear-testing Machines and Corresponding Environmental Conditions for Test

ISO 14242-2 Implants for Surgery - Wear of Total Hip-joint Prostheses - Part 2: Methods of Measurement

ISO 21534 Non-active Surgical Implants - Joint Replacement Implants - Particular Requirements

3 Terms, Definitions and Classification

3.1 Terms and definitions

For the purposes of this standard, the terms and definitions established in ISO 21534 and ISO 7206-1 and the following ones apply.

3.1.1 Hip joint replacement

Implant used to replace one or both of the articulating surfaces of the hip joint.

3.1.2 Total hip joint replacement

Implant comprising a femoral component and an acetabulum component intended to replace both of the articulating surfaces of the hip joints.

3.1.3 Partial hip joint replacement

Implant comprising a femoral component intended to replace the femoral articulating surface of the hip joint.

Note: partial hip joint replacement implants incorporate either a bipolar or a unipolar head.

3.1.4 Acetabulum replacement

Implant comprising an acetabulum component intended to replace acetabulum articulating surface of the hip joint.

3.1.5 Femoral component

Part of a total or partial hip joint replacement which is intended to be attached to the femur.

3.1.6 Acetabulum component

Implant of monobloc or modular construction intended to be fixed to the prepared biological acetabulum.

3.1.7 Bipolar head

Part of a femoral component with a concave (inner) surface intended to articulate with the spherical head of the femoral component and a convex (outer) spherical surface intended to articulate with the biological acetabulum.

3.1.8 Unipolar head

Head of a femoral component intended to articulate with the biological acetabulum.

3.1.9 Module component

Femoral or acetabulum component which is assembled by the user from a number of sub-components.

3.1.10 Monobloc component

Femoral or acetabulum component which is supplied as a single unit.

3.2 Classification

3.2.1 Product classification

The classification of hip joint prostheses according to product use and form is detailed in Table 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

Editions of YY 0118

EditionTitleRevisionStatus
YY 0118-2005Hip joint prosthesescurrent editionCurrent
YY 0118-1993Hip joint prosthesesprevious editionSuperseded

This page sells the current edition, YY 0118-2005. Earlier editions are listed for reference only.

How to Download YY 0118-2005

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

YY 0118-2005

$85.00