Valid

SN/T 2697-2010Determination of sulfur, phosphorus, arsenic and chloride in coal for import and export - X-ray fluorescence spectrometric method (English PDF)

进出口煤炭中硫、磷、砷和氯的测定 X射线荧光光谱法

Preview PDF

This is a limited preview

Buy now to download the full PDF (8 pages)

Need quotation for your management?

Get a formal quotation for SN/T 2697-2010 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China

Level / Type

National · Recommended

Issue date

December 12, 2012

Implementation date

July 1, 2013

Scope

SN/T 2697-2010 is the English-translated version of 进出口煤炭中硫、磷、砷和氯的测定 X射线荧光光谱法.

SN/T 2697-2010 is the Chinese standard "Determination of sulfur, phosphorus, arsenic and chloride in coal for import and export - X-ray fluorescence spectrometric method".

Its scope clause reads: This Part of SN/T 3323 specifies potassium dichromate titration, the method to determine the ferrous oxide content in mill scale. This Part is applicable to the determination of ferrous oxide content in mill scale.

The determination range is 10%~60%. Its clauses include method summary; reagents; instruments and equipment; specimen; analysis steps. It was issued by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China on 2012-12-12 and took effect on 2013-07-01.

Found what you need?

Document preview — SN/T 2697-2010

National Standard of the People's Republic of China

Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China

Foreword...3
1 Scope...4
2 Normative references...4
3 Method summary...4
4 Reagents...4
5 Instruments and equipment...5
6 Specimen...5
7 Analysis steps...5
8 Result calculation...6
9 Precision...7
Annex A (normative) Determination of hygroscopic water in mill scale...8

1 Scope

This Part of SN/T 3323 specifies potassium dichromate titration, the method to determine the ferrous oxide content in mill scale.

This Part is applicable to the determination of ferrous oxide content in mill scale. The determination range is 10%~60%.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 6682, Water for analytical laboratory use - Specification and test methods

GB/T 6730.6-1986, Methods for chemical analysis of iron ores - The ferric chloride- sodium acetate volumetric method for the determination of metallic iron content

GB/T 6730.7-1986, Methods for chemical analysis of iron ores - The sulfosalicylic acid photometric method for the determination of metallic iron content

3 Method summary

In the absence of air, use hydrochloric acid and sodium fluoride to decompose the specimen. Use sodium diphenylamine sulfonate as indicator. Determine ferrous and metallic iron content by potassium dichromate volumetric method. After subtracting the amount of metallic iron, the amount of ferrous iron is obtained.

4 Reagents

Unless otherwise stated, all reagents are analytically pure and above. Water is grade two water specified in GB/T 6682.

4.1 Sodium fluoride.

4.2 Sodium bicarbonate.

4.3 Hydrochloric acid (rho=1.19g/mL).

4.4 Saturated sodium bicarbonate solution.

4.5 Mixed sulfuric acid: Put 200mL of sulfuric acid (rho=1.84g/mL) under stirring, then

pour into 500mL of water slowly. Then, add 300mL of phosphoric acid (rho=l.70g/mL).

Mix well.

4.6 Sodium diphenylamine sulfonate solution (2g/L): Weigh 0.2g of sodium

diphenylamine sulfonate and dissolve in 100mL of water.

4.7 Potassium dichromate standard titration solution (0.0050mol/L): Weigh 1.4709g of

potassium dichromate (reference reagent) that has been pre-dried at 150°C for 1h, and dissolve in water. Transfer into a 1000mL volumetric flask. Use water to dilute to the scale. Mix well.

4.8 Ferrous ammonium sulfate solution (about 0.03mol/L): Weigh 11.82g of ferrous

ammonium sulfate [(NH4)2(SO4)2·6H2O] and dissolve in sulfuric acid (5+95). Transfer into a 1000mL volumetric flask. Use sulfuric acid (5+95) to dilute to the scale. Mix well.

5 Instruments and equipment

5.1 Balance: the sensitivity is 0.1mg.

5.2 Geiger funnel: 250mL.

6 Specimen

The specimen shall pass through the sieve mesh of 0.100mm.

7 Analysis steps

7.1 Test material

Weigh about 0.15g of specimen (Chapter 6), accurate to 0.0001g.

Weigh two portions of test material for parallel determination. Take the average value as the result.

7.2 Blank test

Conduct the blank test, along with test material.

7.3 Determination

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 8 pages — is available in the English PDF.

Referenced standards

Normative references

How to Download SN/T 2697-2010

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.