QC/T 564-2008Performance requirements and bench test methods for passenger car brakes (English PDF)
乘用车制动器性能要求及台架试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for QC/T 564-2008 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
June 4, 2008
Implementation date
November 1, 2008
Scope
QC/T 564-2008 is the English-translated version of 乘用车制动器性能要求及台架试验方法.
QC/T 564-2008 is the Chinese standard "Performance requirements and bench test methods for passenger car brakes". Its scope clause reads: This standard specifies the performance requirements and bench test methods of passenger car service brake.
This standard is applicable to service brake assembly and friction lining (filler block) assembly for M1 category vehicle specified in GB/T 15089. Its clauses include terms and definitions.
Found what you need?
Document preview — QC/T 564-2008
National Standard of the People's Republic of China
- Replacing
- QC/T 564-1999
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Contents
- Contents i
- Foreword
- 1 Scope
- 2 Normative Referances
- 3 Terms and Definitions
- 4 Performance Requirements
- 5 Relevant Requirements of Test
- 6 Test Preparation
- 7 Test Methods and Conditions
- Annex A (Normative) Value method of Braking Torque
1 Scope
This standard specifies the performance requirements and bench test methods of passenger car service brake.
This standard is applicable to service brake assembly and friction lining (filler block) assembly for M1 category vehicle specified in GB/T 15089.
2 Normative References
The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated reference, subsequent amendments to, or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest editions of these documents are applicable. For undated references, the latest edition of the normative document referred to applies.
GB/T 15089 Classification of Power-driven Vehicles and Trailers (GB/T 15089-2001, eqv ITU ECE R.E.3)
QC/T 556 Automotive Brake-Temperature Measurement and Thermocouple Installation
3 Terms and Definitions
The following terms and definitions are applicable to this standard.
3.1 Braking period
The time from starting a braking to starting next start of braking in a continuous braking process.
Note: The unit of braking period is in second (S).
3.2 Initial braking temperature
The temperature of brake drum (disc) or friction lining (filler block) when starting braking.
Note: The unit of initial braking temperature is in °C.
3.3 Average braking torque
The ordinate value gained with the method of the area covered by the changing curve of braking torque with braking time, being divided by the active braking time during a braking process; it is detailed in Annex A.
Note: The unit of initial braking temperature is in N·m.
3.4 Maximum braking torque
The maximum value of longitudinal coordinate on the changing curve of braking torque with braking time during a braking process; it is detailed in Mmax of Annex A.
Note: The unit of maximum braking torque is in N·m.
3.5 Minimum braking torque
The minimum value of longitudinal coordinate on the changing curve of braking torque with braking time during a braking process; it is detailed in Mmin of Annex A.
Note: The unit of braking torque is in N·m.
3.6 Average braking pressure
The ordinate value gained with the method of the area covered by the changing curve of braking pressure with braking time, being divided by the active braking time in a braking process; it is detailed in Annex A.
Note: The unit of baverage braking pressure is in MPa.
3.7 Average braking torque over average braking pressure
The ratio of average braking torque and average braking pressure during the process of a braking.
3.8 Baking final temperature
The maximum temperature of brake drum (disc) or friction lining (filler block) during the process of a braking or after the braking is terminated.
Note: The unit of braking final temperature is in °C.
3.9 Fade rate
The decreasing and increasing degree of braking torque in the fade test; it is expressed in percentage, and calculated according to Formula (1) and Formula (2).
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
Editions of QC/T 564
| Edition | Title | Revision | Status |
|---|---|---|---|
| QC/T 564-2008 | Performance requirements and bench test methods for passenger car brakes | current edition | Current |
| QC/T 564-1999 | Performance requirements and bench test methods for passenger car brakes | previous edition | Superseded |
This page sells the current edition, QC/T 564-2008. Earlier editions are listed for reference only.
How to Download QC/T 564-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
QC/T 1005-2026 — Performance requirements and bench test methods for hydraulic solenoid valve assembly of electronic stability control system and antilock brake system of automoive
QC/T 1022-2026 — Technical specifications and test methods of reduction gearbox for battery electric vehicles
QC/T 1041-2026 — Control system of fuel evaporative pollutants from Motorcycles with petrol engine
QC/T 564-2008
$75.00