QC/T 25-2004Technical specifications for automotive dry friction clutch assemblies (English PDF)
汽车干磨擦式离合器总成技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for QC/T 25-2004 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
February 10, 2004
Implementation date
August 1, 2004
Scope
QC/T 25-2004 is the English-translated version of 汽车干磨擦式离合器总成技术条件.
QC/T 25-2004 is the Chinese standard "Technical specifications for automotive dry friction clutch assemblies".
Its scope clause reads: This standard specifies the terms and definitions, technical requirements, test methods, test methods, inspection rules, marking, packaging, transportation, and storage of auto dry friction clutch assembly (including lid assembly and driven plate assembly, hereinafter called clutch).
This standard is applicable to auto dry friction clutch. Its clauses include terms and definitions; test methods; inspection rules; marking, packaging, transportation, and storage.
Found what you need?
Document preview — QC/T 25-2004
National Standard of the People's Republic of China
- Replacing
- QC/T 25-1992
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Preface3
- 1 Scope4
- 2 Normative references4
- 3 Terms and Definitions4
- 4 Technical Requirements5
- 5 Test Methods9
- 6 Inspection rules10
- 7 Marking, Packaging, Transportation, and Storage11
1 Scope
This standard specifies the terms and definitions, technical requirements, test methods, test methods, inspection rules, marking, packaging, transportation, and storage of auto dry friction clutch assembly (including lid assembly and driven plate assembly, hereinafter called clutch).
This standard is applicable to auto dry friction clutch.
2 Normative references
The provisions in following documents become the provisions of this standard through reference in this
Standard. For dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this standard, however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies.
QC/T 27-2004 Bench test method of automobile clutch (The Stand Test Method of Auto Dry Friction
Clutch Assembly)
3 Terms and Definitions
The following terms and definitions are applicable to this standard.
3.1 Release travel
Under specified work conditions, the travel of release finger (rod) of the clutch, from complete connection to complete release.
3.2 Release load
In release procedure, the load applied on the end of the release finger (rod) of the lid assembly.
3.3 Lift
Under the specified release travel, the minimum value of the displacement of all points on the work surface of the pressure plate.
3.4 Pressure plate parallelism
Under the specified release travel, the difference between the maximum value and minimum value of the displacement of all points on the work surface of the pressure plate.
4.3.3 Failure rotating speed of the clutch
4.3.3.1 When the lid assembly is under the specified test condition, the failure rotating speed shall not be less than 1.8 times of the maximum power speed of the engine.
4.3.3.2 When the driven plate assembly is under the specified test condition, the failure rotating speed shall not be less than 1.6 times of the maximum power speed of the engine.
4.3.4 Cushion resilience durability of driven plate assembly
Under the working pressure, after 2.5X10
5 times of cushion resilience test on the driven plate:
a) Cushion resilience shall not be less than 80% of initial value;
b) There is no damage on the wave-shape disk and no loosen on rivet.
4.3.5 Torque durability of driven plate assembly
After the driven plate has been gone through 5X10
6 times test:
a) Limit torque is not less than 80% of initial value;
b) The friction damp torque of the torque absorber shall not be less than 60% of initial value;
c) All components must not fail.
4.4 Other requirements
4.4.1
The clutch shall be clean, and no greasy dirt on the surface of the friction disks.
4.4.2
All metal components of the clutch shall be anti-corrosively treated. Anti-corrosive agent is allowed on the surface of the pressure plate.
4.4.3
The special technical requirements other than those specified in this standard are subject to the negotiation between the suppliers and the customers.
4.4.4
The clutch shall be kept in according to 7.4. If rust occurs 6 months after leaving factory, the supplier shall hold the responsibility. The clutch shall be used as specified. If damage occurs when the use life is not more than 1 year and driving is not more than 3x10
4 km, the supplier shall hold the responsibility.
5 Test Methods
Test method shall be according to QC/T 27.
6 Inspection rules
6.1 Ex-factory inspection
6.1.1
The clutches shall be checked for conformance before leaving the factory.
6.1.2
The items of ex-factory inspection are as follows:
a) Lid assembly load characteristic;
b) Lid assembly release characteristic;
c) The assembling height deviation of the release finger (rod) and the end-face leaping amount of the release finger (rod);
d) The unbalance amount of the lid assembly;
e) The drag torque or drag travel of the driven plate assembly;
f) Unbalance amount of the driven plate assembly;
g) Work compressing thickness of the driven plate assembly;
h) The torque shocking absorbing characteristic of the driven plate assembly;
i) Appearance quality.
6.2 Type Test
Type test shall be done, when there is one of the following conditions:
a) The trial type-indentification of new product or old product transferring production;
b) After mass production, when there is significant change in structure, engineering or materials which may affect the product performance;
c) During mass production, periodically or after accumulating certain quantity, it shall periodically conduct an inspection;
d) After the production is shut-downed for long time, and when the production is resumed;
e) When the ex-factory inspection result is significantly different from the last type test;
f) When it is required by the National Quality Supervision Agencies.
6.2.2
Type test items:
a) Static-release durability test on lid assembly;
b) Dynamic-release durability test on lid assembly;
c) High speed resistive test on lid assembly;
d) Friction feature test on clutch;
e) Anti-adhesion test (negotiated with customers);
f) Durability test on cushion resilience of the driven plates;
g) Durability test on the driven plate assembly torque;
h) High speed resistive test on the driven plate.
6.2.3
One sampling test shall be done for each item in the model test.
7 Marking, Packaging, Transportation, and Storage
7.1 Marking
Manufacturer's name and specifications shall be marked on each clutch,
7.2 Packaging
7.2.1 The package of the clutches shall ensure that the products will not be damaged during normal transportation. And anti corrosion method shall be adopted.
7.2.2
The Certificate of Conformance shall be included in the package.
7.2.3
On the package box, it shall indicate:
a) Manufacturer's name, trademark, address;
b) Product name;
c) Model and specification;
d) The implemented standard number;
e) Quantity in the package;
f) Signs like “Be careful to handle” and “Keep from moisture”;
g) Production date.
7.3 Transportation
7.3.1 The clutch shall be kept clean during the transportation. Driven plate shall not be smeared with oil.
7.3.2
Keep away from rain water and moist.
7.3.3
Handle carefully during the transportation.
7.4 Storage
The products shall be stored and prevented from moist, oil dirt and corrosion.
__________ END __________ […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
Editions of QC/T 25
| Edition | Title | Revision | Status |
|---|---|---|---|
| QC/T 25-2004 | Technical specifications for automotive dry friction clutch assemblies | current edition | Current |
| QC/T 25-1992 | Technical specifications for automotive dry friction clutch assemblies | previous edition | Superseded |
This page sells the current edition, QC/T 25-2004. Earlier editions are listed for reference only.
How to Download QC/T 25-2004
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
QC/T 1005-2026 — Performance requirements and bench test methods for hydraulic solenoid valve assembly of electronic stability control system and antilock brake system of automoive
QC/T 1022-2026 — Technical specifications and test methods of reduction gearbox for battery electric vehicles
QC/T 1041-2026 — Control system of fuel evaporative pollutants from Motorcycles with petrol engine
QC/T 25-2004
$55.00