Valid

QC/T 1105-2019Performance requirements and test methods for earth bolts (English PDF)

接地螺栓性能要求及试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (21 pages)

Need quotation for your management?

Get a formal quotation for QC/T 1105-2019 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

August 2, 2019

Implementation date

January 1, 2020

Scope

QC/T 1105-2019 is the English-translated version of 接地螺栓性能要求及试验方法.

QC/T 1105-2019 covers earth bolts, the connecting bolts between the grounding points of circuits, equipment and subsystems and the reference ground, which in an automotive electronic system is the frame or the cabin.

It specifies the grounding performance requirements and the related test methods, and it applies to earth bolts with a thread specification of M6 and M8, a mechanical performance grade of 8.8 and a product grade A. The document is built around a voltage drop measurement repeated after each conditioning.

For a common connection the bolt is tightened to the minimum torque given in Table 2 and the voltage drop is measured, then it is tightened to the maximum torque in Table 2 and measured again; where an impact wrench is used it is set to the torque of the production process.

The repeated disassembly and assembly test counts one tightening and removal as a cycle and runs 10 cycles, with the impact wrench used only in the first cycle and a torque wrench from the second onwards.

The salt spray test hangs the specimen with the bolt installed in the chamber, follows the neutral salt spray test of GB/T 10125 for 23 hours, then stands the specimen outside the chamber for 1 hour, repeated for 4 cycles.

The vibration test mounts the specimen in three installation postures and runs the conditions of Table 5 in three mutually perpendicular directions. Each of these tests is run on 10 bolts and each ends with the voltage drop test.

Found what you need?

Document preview — QC/T 1105-2019

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword3
  • 1 Scope4
  • 2 Normative references4
  • 3 Terms and definitions4
  • 4 Performance requirements for earth bolts5
  • 5 Preparation for electrical performance test5
  • 6 Test methods for electrical properties6

1 Scope

1.1 This standard specifies the grounding performance requirements and related test methods for earth bolts.

1.2 This standard is applicable to the earth bolts, which have a thread specification M6 and M8, a mechanical performance grade 8.8, a product grade A.

2 Normative references

The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this standard.

GB/T 10125 Corrosion tests in artificial atmospheres - Salt spray tests

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Earth

Refers to the connection of a circuit, equipment, subsystem to the reference ground, to provide an equipotential point or plane. The reference ground of the automotive electronic system is the frame or the cabin; the negative wire of the battery is directly placed on the frame or cabin.

3.2 Earth bolt

Connecting bolts, between the grounding points of circuits, equipment, subsystems and the reference ground.

6 Test methods for electrical properties

6.2 Common connection

6.2.1 Tightening by torque wrench

Each bolt shall be tightened, according to the minimum torque in Table 2. The voltage drop shall be measured, according to 6.1. Then it is tightened, according to the maximum torque in Table 2. The voltage drop shall be measured, according to 6.1. The number of test earth bolts is 10.

6.2.2 Tightening by impact wrench

If an impact wrench is used, tighten it according to the torque setting of the production process. Measure the voltage drop according to 6.1. The number of test bolts is 10.

6.3 Repeated disassembly & assembly

Take one tightening-disassembly & assembly of the earth bolt as 1 cycle. Repeat 10 cycles. When tightening, use the impact wrench only in the 1st cycle; use the torque wrench after the 2nd cycle. Then carry out the voltage drop test, according to 6.1. The number of test bolts is 10.

6.4 Salt spray

Hang the specimen with the earth bolt installed (see Figure 1) in the salt spray test chamber. According to the neutral salt spray test in GB/T 10125, spray for 23 hours. Then place it outside the salt spray test chamber, for 1 hour, during which it shall not direct contact the specimen. After repeating 4 cycles, carry out the voltage drop test according to 6.1. The number of test bolts is 10.

6.5 Vibration

Install the specimen on the vibration testing machine, in the three installation postures as shown in Figure 4. Carry out the test, according to the conditions in Table 5. The vibration directions are three directions perpendicular to each other in the up and down, left and right, front and rear directions, as relative to the installation state. Then carry out the voltage drop test according to 6.1. The number of test bolts is 10.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 21 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download QC/T 1105-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
21 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

QC/T 1105-2019

$135.00