Valid

QC/T 1075-2017Technical specifications for metallic honeycomb substrates for exhaust catalytic converters (English PDF)

排气催化转化器用金属蜂窝载体技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for QC/T 1075-2017 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

April 12, 2017

Implementation date

October 1, 2017

Scope

QC/T 1075-2017 is the English-translated version of 排气催化转化器用金属蜂窝载体技术条件.

QC/T 1075-2017 is the Chinese standard "Technical specification of honeycomb metal substrate for exhaust catalytic converter".

Its scope clause reads: This Standard specifies the technical requirements, materials, test methods, inspection rules, marking, packaging, transportation and storage of the honeycomb metal substrate for exhaust catalytic converter.

This Standard applies to the honeycomb metal substrate for exhaust catalytic converter of Class M and Class N motor vehicles. Its clauses include terms and definitions; technical requirements; test methods; inspection rules; marking, packaging, transportation and storage.

It was issued by the Ministry of Industry and Information Technology of the People's Republic of China on APRIL 12, 2017 and took effect on OCTOBER 1, 2017.

Found what you need?

Document preview — QC/T 1075-2017

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword7
  • 1 Scope8
  • 2 Normative references8
  • 3 Terms and definitions8
  • 4 Technical requirements10
  • 5 Test methods12
  • 6 Inspection rules15
  • 7 Marking, packaging, transportation and storage16
  • Appendix A (Informative) Substrate specification parameters17

1 Scope

This Standard specifies the technical requirements, materials, test methods, inspection rules, marking, packaging, transportation and storage of the honeycomb metal substrate for exhaust catalytic converter.

This Standard applies to the honeycomb metal substrate for exhaust catalytic converter of Class M and Class N motor vehicles.

2 Normative references

The following documents are essential for the application of this Standard.

For dated references, only the dated editions apply to this Standard. For undated references, the latest editions (including all amendments) apply to this Standard.

GB/T 31942 FeCrAl foil for metallic honeycomb substrates

3 Terms and definitions

The following terms and definitions apply to this Standard.

3.1 Honeycombed structure

A honeycomb-like spatial structure composed of a plurality of spatial channels surrounded by thin walls having a certain outer shape, such as a cylindrical shape.

3.2 Honeycomb metal substrate (hereinafter referred to as substrate)

A place where the metal material is fabricated into a honeycombed structure and a housing, providing a purification reaction of the engine exhaust.

3.3 Density of cells

The end face of the honeycombed structure, excluding the outermost layer and the surrounding layer of the middle hole, the number of holes per unit area may be expressed in metric (or British) area units.

3.4 Net volume of substrate

The volume of the honeycombed structure contained in a single substrate, and the substrate housing is not counted. If a single substrate contains multiple relatively independent honeycombed structures, the void volume between each honeycombed structure shall be excluded.

3.5 Total volume of substrate

The volume of space enclosed by the substrate size.

3.6 Substrate size

The outer size of the substrate.

3.7 Substrate mass

The total mass of the housing of the substrate before coating the catalyst and the honeycombed structure fixed to the interior thereof.

3.8 Catalytic converter

A device mounted in an exhaust system of an automobile to perform oxidation and/or reduction reaction by a catalyst to reduce the emission of harmful substances such as CO, HC, NOx, and PM in the exhaust gas.

3.9 Manifold catalytic converter for petrol vehicles (hereinafter

referred to as manifold catalytic converter)

A catalytic converter assembly component that is mounted in the engine compartment of a petrol vehicle and consists of an engine exhaust manifold and a catalytic converter, and the junction of each branch of the engine manifold to the inlet end of the catalytic converter is not more than 400mm.

3.10 Under-floor catalytic converter for petrol vehicles (hereinafter

referred to as under-floor catalytic converter)

A catalytic converter assembly that is mounted under the petrol vehicle chassis and at a distance of more than 400mm from the engine exhaust manifold.

3.11 Aftertreatment devices for diesel vehicle exhaust

A device mounted in the exhaust system of a diesel engine that can reduce the emission of pollutants in the exhaust gas through various physical and chemical functions.

4 Technical requirements

d) Other phenomena that affect normal use.

4.5 Vibration durability

4.5.1 The substrate shall be subjected to a thermal vibration test in accordance with 5.3 of this Standard.

4.5.2 Before and after the thermal vibration test, the differential pressure of the front and rear end faces under the substrate airspeed of (60,000±600)h-1 is measured at normal temperature, and the change of the differential pressure value shall not exceed 15%.

4.5.3 After the thermal vibration test, the substrate shall not exhibit obvious deformation of the honeycomb, falling off or detachment of the honeycombed structure and the housing, severe deformation of the outer contour, and other damages. Other forms of damage may be specified in detail by the company's technical requirements.

4.6 Temperature shock durability

4.6.1 The substrate shall be subjected to a temperature shock test in accordance with 5.4 of this Standard.

4.6.2 Before and after the temperature shock test, the differential pressure of the front and rear end faces under the substrate airspeed of (60,000±600)h-1 is measured at normal temperature, and the change of the differential pressure value shall not exceed 15%.

4.6.3 After the temperature shock test, the substrate shall not exhibit obvious deformation of the honeycomb, falling off or detachment of the honeycombed structure and the housing, severe deformation of the outer contour, and other damages. Other forms of damage may be specified in detail by the company's technical requirements.

5 Test methods

5.1 General

5.1.1 Before the test, it shall be confirmed that the substrate is in a brand new state in which the catalyst is not coated.

5.1.2 MEASURE, RECORD and CONFIRM that the initial state of the test sample meets the specifications of 4.2.

5.1.3 According to the different classification categories of the substrate application environment, there are differences in different types of test conditions. end faces of the substrate at the airspeed of (60,000±600)h-1 is measured at normal temperature, and check the integrity of the substrate.

6 Inspection rules

6.1 Inspection category

The inspection of the substrate is divided into exit-factory inspection and type inspection.

6.2 Exit-factory inspection

6.2.1 Each product shall be inspected at the factory before leaving the factory, and shall be inspected by the quality inspection department of the factory, and a certificate of conformity shall be issued.

6.2.2 The inspection items and requirements shall comply with the provisions of 4.1 to 4.3.

6.3 Type inspection

In case of any of the following circumstances, the product shall be subject to type inspection:

a) new product finalization;

b) continuously produced products, once every two years;

c) re-production when the production interval is more than one year;

d) when there are major changes in product design processes, materials, etc.;

e) when there is a problem with the quality of the product; and

f) other time when it is deemed necessary.

6.3.1 Sampling method

The type inspection adopts random sampling. Three products are randomly selected from the products qualified for exit-factory inspection, and the sampling base is not less than 100.

6.3.2 Inspection item

The test items as required in 4.4 to 4.6.

6.3.3 Determination rule

6.3.3.1 The type inspection results shall comply with the corresponding provisions of 4 Technical requirements.

6.3.3.2 In the type inspection, if any inspection item is unqualified, it shall be […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download QC/T 1075-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

QC/T 1075-2017

$125.00