Valid

NB/T 47004.1-2017Plate heat exchangers - Part 1: Plate-and-frame heat exchangers (English PDF)

板式热交换器 第1部分:可拆卸板式热交换器

Preview PDF

This is a limited preview

Buy now to download the full PDF (36 pages)

Need quotation for your management?

Get a formal quotation for NB/T 47004.1-2017 in 30 minutes.

Issued by

NEA

Level / Type

Industry · Recommended

Issue date

December 27, 2017

Implementation date

June 1, 2018

Scope

NB/T 47004.1-2017 is the English-translated version of 板式热交换器 第1部分:可拆卸板式热交换器.

NB/T 47004.1-2017 is the Chinese standard "Plate heat exchangers - Part 1: Plate-and-frame heat exchangers".

Its scope clause reads: This part specifies the requirements for material, design, fabrication, inspection, performance determination and energy efficiency evaluation of plate-and-frame heat exchangers (hereinafter referred to as plate heat exchangers).

This part is applicable to gasketed or semi-welded plate-and-frame heat exchangers. Other plate heat exchangers, where designed, fabricated and inspected by reference to this standard, shall be approved and agreed by the purchaser.

Design pressure applicable to this part: a) the design pressure of gasketed plate heat exchanger is not greater than 3.0MPa; b) the design pressure of semi-welded plate heat exchanger is not greater than 6.0MPa.

The design temperature range applicable to this part shall be determined according to the allowable service temperature of materials of gaskets and other elements. Its clauses include terms and definitions; general requirements.

Found what you need?

Document preview — NB/T 47004.1-2017

National Standard of the People's Republic of China

Replacing
NB/T 47004-2009

Issued by: National Energy Administration of the People's Republic of China

Contents

  • Foreword i
  • Introduction iii
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 General requirements
  • 5 Materials
  • 6 Design
  • 7 Drawings and quality certificates
  • 8 Fabrication
  • 9 Inspection and performance determination
  • 10 Energy efficiency evaluation
  • 11 Marking, transportation, packaging and storage
  • Annex A (Normative) Plate heat exchanger gasket
  • Annex B (Informative) Plate heat exchanger checklist
  • Annex C (Informative) Plate heat exchanger data sheets

1 Scope

1.1

This part specifies the requirements for material, design, fabrication, inspection, performance determination and energy efficiency evaluation of plate-and-frame heat exchangers (hereinafter referred to as plate heat exchangers).

1.2

This part is applicable to gasketed or semi-welded plate-and-frame heat exchangers. Other plate heat exchangers, where designed, fabricated and inspected by reference to this standard, shall be approved and agreed by the purchaser.

1.3

Design pressure applicable to this part:

a) the design pressure of gasketed plate heat exchanger is not greater than 3.0MPa;

b) the design pressure of semi-welded plate heat exchanger is not greater than 6.0MPa.

1.4

The design temperature range applicable to this part shall be determined according to the allowable service temperature of materials of gaskets and other elements.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the normative document (including any amendments) applies.

GB/T 150.2-2011 Pressure vessels - Part 2: Materials

GB/T 699 Quality carbon structure steel

GB/T 700 Carbon structural steels (ISO 630: 1995, NEQ)

GB/T 713 Steel plates for boilers and pressure vessels

GB/T 1220 Stainless steel bar

GB/T 1591 High strength low alloy structural steels

GB/T 2054 Nickel and nickel alloy plate and sheet

GB/T 3077 Alloy structure steels

GB/T 3274 Hot-rolled plates and strips of carbon structural steels and high strength low alloy structural steels (ISO 13976: 2005, ISO 630: 1995, NEQ)

GB/T 3280 Cold rolled stainless steel plate, sheet and strip

GB/T 3621 Titanium and titanium alloy plate and sheet

GB/T 3624 Titanium and titanium alloy tubes

GB/T 3625 Titanium and titanium alloy tube for condensers and heat exchangers

GB/T 4156 Metallic materials - Sheet and strip - Erichsen cupping test (ISO 20482: 2003, IDT)

GB/T 4237 Hot rolled stainless steel plate, sheet and strip

GB/T 8163 Seamless steel tubes for liquid service

GB/T 13296 Seamless stainless steel tubes for boiler and heat exchanger

GB/T 14845 Titanium sheet for plate heat exchangers

GB/T 14976 Seamless stainless steel pipes for fluid transport

GB/T 26299 Copper alloy sheet and strip for anti-corrosion

GB/T 27698.1 Test method for the performance of heat exchangers and heat exchange element - Part 1:General requirements

GB/T 27698.3 Test method for the performance of heat exchangers and heat exchange element - Part 3: Plate heat exchanger

NB/T 47008 Carbon steel and alloy steel forgings for pressure equipments

NB/T 47009 Alloy steel forgings for low temperature pressure equipment

NB/T 47010 Stainless and heat-resisting steel forgings for pressure equipments

NB/T 47013 (All parts) Nondestructive testing of pressure equipments

NB/T 47014 Welding procedure qualification for pressure equipment

NB/T 47018 Technical permission of welding materials for pressure equipment

YB/T 5354 Cold-rolled plates of corrosion-resisting alloys

3 Terms and definitions

For the purposes of this part, the following terms and definitions apply.

3.1 plate

corrugated plate formed by precise pressing

3.2 heat transfer area per plate

the surface area of single side of a plate (the shaded part in Figure 1) involved in heat transfer, which is calculated using Equation (1):

a=phi·a1 (1)

Where, a - - the heat transfer area per plate, m2;

a1 - - the projected area of a plate involved in heat transfer, m2;

Figure 1

phi - - the corrugation expansion coefficient, calculated using Equation (2):

(2)

Where, t' - - the surface length of the corrugated pitch (as shown in Figure 2), mm;

t - - the corrugated pitch (as shown in Figure 2), mm.

Note: when the difference between the corrugated pitch in diversion zone and that in corrugated zone is large, the heat transfer area of the diversion zone and the corrugated zone shall be calculated respectively, and then added together.

Figure 2

3.3

the nominal heat transfer area per plate rounded heat transfer area per plate

3.4 connector plate

plate that divides a plate heat exchanger into two or more heat transfer sections

3.5 end plates

plate which prevents the fluids from contacting the connector plate or cover plate

3.6 heat transfer area

rounded sum of heat transfer area per plate of all plates of a plate heat exchanger, which are in contact with medium on both sides

3.7 frame

assembly that provides the structural support and pressure sealing of a plate heat exchanger

3.8 pass plate

plate used to change the direction of medium flow in a plate heat exchanger with two or more passes

3.9 pass

a group of channels in which the medium flows in the same direction in a plate heat exchanger

3.10 channel

medium flow channel formed by adjacent plates in a plate heat exchanger

3.11 pass and channel arrangement

pass and channel arrangement in plate heat exchanger, expressed as:

(3)

Where,

M1, M2, ..., Mi - - the number of passes having the same number of channels on heat medium side from the fixed cover plate;

N1, N2, ..., Ni - - the number of channels corresponding to M1, M2, ..., Mi passes;

m1, m2, ..., mi - - the number of passes having the same number of channels on cold medium side from the fixed cover plate;

n1, n2, ..., ni - - the number of channels corresponding to m1, m2, ..., mi passes.

3.12 equivalent diameter

ratio of 4 times of sectional area of channels between plates to the wet perimeter

3.13 normal channel space

average distance between the channels of plate heat exchanger

3.14 plate gap

average distance b between two adjacent plates of plate heat exchanger, as shown in Figure 2

3.15 chevron depth

plate chevron forming depth h, as shown in Figure 2

3.16 plate chevron angle

angle beta formed between the plate chevron and the horizontal, as shown in Figure 1

3.17 plate thickness

standard specification thickness S0 of the plate marked in the drawing

3.18 plate thickness thinning

difference between the actual plate thickness and the thickness at maximum thinning place of formed plate

3.19 port

inlet or outlet opening in the plate

3.20 plate pack

grouping of all plates contained within a frame

3.21 semi-welded plate pair

two plates welded together

3.22 plate heat exchanger

heat exchanger consisting of plate (or semi-welded plate pair), sealing gasket and support frame. Figure 3 shows the composition of a typical plate heat exchanger

Figure 3

3.23 pressure

force acting on unit area vertically. For the purpose of this part, unless otherwise specified, pressure refers to gauge pressure

3.24 operating pressure

maximum pressure possibly existing on any side of plate heat exchanger under normal operating condition

3.25 design pressure

maximum pressure set on any side of plate heat exchanger, which is used as design load conditions together with the corresponding design temperature and shall not be less than the operating pressure

3.26 design temperature

element temperature of plate heat exchanger set under normal operating pressure and corresponding design pressure

3.27

energy efficiency index (EEI) of plate heat exchanger calculated energy efficiency of plate heat exchanger under the test conditions specified in this standard

3.28

the minimum allowable values of energy efficiency of plate heat exchanger the minimum allowable energy efficiency of plate heat exchanger under the test conditions specified in this standard

4 General requirements

4.1 General

The design, fabrication, inspection, performance determination and energy efficiency evaluation of plate heat exchanger shall meet the requirements of this part, the relevant national laws and regulations and safety technical codes as well as the relevant standards, codes and regulations agreed or designated by the purchaser; besides, it shall also meet the requirements of drawings.

4.2 Qualification

4.2.1

The design organization and fabrication organization of plate heat exchanger shall establish and improve various management systems.

4.2.2

The fabrication organization of plate heat exchanger and its sealing gasket shall have the basic conditions for the production of plate heat exchanger and sealing gasket, and should obtain the corresponding safety registration certificate and energy saving registration certificate of plate heat exchanger.

4.3 General requirements

4.3.1 Expression for model of plate heat exchanger

Example 1: the plate heat exchanger with M-shaped plate, port diameter of 200mm, design pressure of 1.6MPa and design temperature of 100°C is expressed as: M20-1.6/100.

Example 2: the plate heat exchanger with V-shaped plate, nominal heat transfer area per plate of 1.3m2, design pressure of 1.0MPa and design temperature of 120°C is expressed as: V13-1.0/120.

4.3.2

The purchaser should confirm the requirements of various clauses in Annex B.

4.3.3

The supplier and the purchaser should jointly complete the requirements of various clauses in Annex C.

4.4 Allowable stress of stud

The safety factor of steel stud is selected according to Table 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 36 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of NB/T 47004.1

EditionTitleRevisionStatus
NB/T 47004.1-2017Plate heat exchangers - Part 1: Plate-and-frame heat exchangerscurrent editionCurrent
NB/T 47004-2009Plate heat exchangers - Part 1: Plate-and-frame heat exchangersprevious editionSuperseded

This page sells the current edition, NB/T 47004.1-2017. Earlier editions are listed for reference only.

How to Download NB/T 47004.1-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
36 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

NB/T 47004.1-2017

$520.00