Valid

NB/T 33009-2013Technical Guide for Electric Vehicle Charging/battery Swap Infrastructure Construction (English PDF)

电动汽车充换电设施建设技术导则

Preview PDF

This is a limited preview

Buy now to download the full PDF (18 pages)

Need quotation for your management?

Get a formal quotation for NB/T 33009-2013 in 30 minutes.

Issued by

NEA

Level / Type

Industry · Recommended

Issue date

November 28, 2013

Implementation date

April 1, 2014

Scope

NB/T 33009-2013 is the English-translated version of 电动汽车充换电设施建设技术导则.

NB/T 33009-2013 is the Chinese standard "Technical Guide for Electric Vehicle Charging/battery Swap Infrastructure Construction".

Its scope clause reads: The electric vehicle charging/battery swap infrastructure construction shall implement relevant national laws, regulations, technical standards, energy-saving and environmental protection policies; so that be technologically advanced, safe and reliable, economical and reasonable, and convenient to use.

This Standard specifies the basic technical principles that shall be followed in the electric vehicle charging/battery swap infrastructure construction; it is applicable to the electric vehicle charging/battery swap infrastructure construction, including AC charging spot, charging station, battery swap station and battery dispatch center, etc. The electric vehicle charging/battery swap infrastructure construction shall follow the principles of unified standard, unified specification, unified identification, optimized distribution, safety and reliability, and moderate advancement.

The electric vehicle charging/battery swap infrastructure shall be reasonably determined the design plan according to the project characteristics, equipment capacity, site environment, energy-saving and environmental protection, and the like factors. Its clauses include general principles; technical principles.

Found what you need?

Document preview — NB/T 33009-2013

National Standard of the People's Republic of China

Issued by: National Energy Administration of the People's Republic of China

Contents

  • Foreword4
  • 1 General Principles6
  • 2 Construction Principles7
  • 2.1 Principles of planning7
  • 2.2 Principles of site selection7
  • 2.3 Layout of charging station/battery swap station8
  • 3 Technical Principles9
  • 3.1 AC charging spot9
  • 3.2 Charging station9
  • 3.3 Type-A battery swap station11
  • 3.4 Type-B battery swap station12
  • 3.5 Battery dispatch center12
  • 3.6 Metering12
  • 3.7 Safety and firefighting13
  • 3.8 Signs and identifications13
  • 4 Project Construction and Acceptance14
  • Explanation of Wording in this Code15
  • List of Quoted Standards16

1 General Principles

1.0.1

The electric vehicle charging/battery swap infrastructure construction shall implement relevant national laws, regulations, technical standards, energy-saving and environmental protection policies; so that be technologically advanced, safe and reliable, economical and reasonable, and convenient to use.

1.0.2

This Standard specifies the basic technical principles that shall be followed in the electric vehicle charging/battery swap infrastructure construction; it is applicable to the electric vehicle charging/battery swap infrastructure construction, including AC charging spot, charging station, battery swap station and battery dispatch center, etc.

1.0.3

The electric vehicle charging/battery swap infrastructure construction shall follow the principles of unified standard, unified specification, unified identification, optimized distribution, safety and reliability, and moderate advancement.

1.0.4

The electric vehicle charging/battery swap infrastructure shall be reasonably determined the design plan according to the project characteristics, equipment capacity, site environment, energy-saving and environmental protection, and the like factors.

1.0.5

The electric vehicle charging/battery swap infrastructure construction shall be compatible with the local electrical vehicle development plan; coordinate to promote with the development of electrical vehicle application; improve the resource utilization efficiency; and fully guarantee the electric power supply of the electric vehicle.

1.0.6

The electric vehicle charging/battery swap infrastructure include the following construction modes, such as AC charging spot, charging station, battery swap station, battery dispatch center, etc. The battery swap station can be divided into Type-A and

Type B battery swap station according to the different functions, and as per the requirements of 5.2 specified in GB/T 29772-2012 General Requirements of Electric

Vehicle Battery Swap Station.

3 Technical Principles

3.1 AC charging spot

3.1.1

The functions and technical indicators shall meet the requirements of current

industry standard NB/T 33002 Specification for Electric Vehicle A.C Charging Point.

3.1.2

The design of the power supply and distribution system shall meet the relevant requirements of the current national standard GB 50054 Code for Design of Low- voltage Electrical Distribution System.

3.1.3

The charging coupler shall meet the requirements of the current national standard GB/T 20234.2 Connection Set for Conductive Charging of Electric Vehicles -

Part 2: AC Charging Coupler.

3.1.4

AC charging spot shall be equipped with necessary external protective equipment.

3.1.5

AC charging spot shall have the communication interface with the superior monitoring and management system.

3.2 Charging station

3.2.1

The charging station power supply system shall meet the following conditions:

1 The design of transformer room and power distribution room shall meet the requirements of current national standard GB 50053 Code for Design of 10kV &

Under Electric Substation; while the design of low-voltage power distribution part shall meet the requirements of current national standard GB 50054 Code for

Design of Low-voltage Electrical Distribution System.

2 The number of power supplies shall be selected according to the degree of importance and power distribution capacity.

3 The power supply voltage level shall be determined according to the power distribution capacity.

4 The capacity of the power supply system shall meet the requirements for the electricity consumption by the charging, lighting, monitoring, etc. in the charging station; and leave a certain margin.

5 Take effective power quality control measures; reduce the impact on the public power grid; so that the power quality of the charging station at the access point of the public power grid meet the requirements of current national standard GB/T 29316 Power Quality Requirements for Electric Vehicle Charging/Battery Swap

Infrastructure.

3.3 Type-A battery swap station

3.3.1

The design of power supply system in Type-A battery swap station shall meet the

requirements of 3.2.1.

3.3.2

The charging system in Type-A battery swap station shall meet the following conditions:

1 The function and technical indicators of in-station charger can refer to the requirements of current industry standard NB/T 33001 Specification for Electric

Vehicle off-Board Conductive Charger.

2 The in-station charger shall be properly arranged, and facilitate the ventilation and heat dissipation.

3 The in-station charger shall have the function of data communication with the monitoring system.

3.3.3

The battery pack swap system in the Type-A battery swap station shall meet the following conditions:

1 The battery pack shall have standard mechanical dimensions and electrical parameters.

2 The charging stand shall be matched with the battery pack; and achieve a safe and reliable connection with battery pack.

3 The charging stand shall have corresponding status indication and communication interface; and have automatic alarm function.

4 The charging stand shall have a guiding function for the battery pack; and have limiting device for the battery pack.

5 The battery pack connector shall adopt the structure with electrical and electronic separation; and has a function of preventing mis-insertion.

6 The battery pack swap equipment shall have maximum power limit and anti-tip function.

7 Automatic and semi-automatic battery pack swap equipment shall have a manual emergency stop function.

3.3.4

The monitoring system in Type-A battery swap station shall meet the following conditions:

1 The monitoring system of battery swap station shall meet the requirements of

3.2.3.

3.6.3

The metering between the off-board charger and electric vehicle shall conform

to the current national standard GB/T 29318 Electric Energy Metering for Electric

Vehicle off-Board Charger.

3.6.4

When taking the battery swap mode, the electric energy metering between the battery swap station and the electric vehicle user shall adopt corresponding metering mode according to the operation mode.

3.7 Safety and firefighting

3.7.1

The charging/battery swap infrastructure shall meet the firefighting requirements of current national standards GB 50016 Code of Design on Building Fire Protection and Prevention, GB 50140 Code for Design of Extinguisher Distribution in Buildings, and current industry standard DL 5027 Typical Extinguishing and Protection Regulation of Electrical Equipment.

3.7.2

The fire separation distance between the charging/battery swap infrastructure and other civil buildings (structures), various factories, warehouses, storage yards, storage tanks shall conform to the Class-D factory provisions of GB 50016.

3.7.3

Accident battery isolation measures shall be taken in the battery swap station.

3.7.4

The lightning protection design of the charging station and battery swap station shall conform to the relevant provisions of current national standard GB 50057 Design

Code for Protection of Structures against Lightning.

3.7.5

The grounding of the AC electrical equipment shall conform to the relevant provisions of current industry standard DL/T 621 Grounding for AC Electrical

Installations.

3.7.6

Take effective isolation measures, and set warning signs to prevent the unrelated personnel from entering the charging area and battery swap area.

3.8 Signs and identifications

3.8.1

The guiding signs and safety warning signs, etc. shall be set in a conspicuous position of the charging/battery swap infrastructure.

3.8.2

The necessary charging parameters and operating instructions shall be indicated in a conspicuous position of the charging equipment and battery swap equipment.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 18 pages — is available in the English PDF.

Similar standards

How to Download NB/T 33009-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
18 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

NB/T 33009-2013

$315.00