Valid

JR/T 0052-2009Bank card specification (English PDF)

Preview PDF

This is a limited preview

Buy now to download the full PDF (11 pages)

Need quotation for your management?

Get a formal quotation for JR/T 0052-2009 in 30 minutes.

Issued by

People's Bank of China 3.No action is required - Full-copy of this standard will be automatically & immediatel

Level / Type

National · Recommended

Issue date

May 18, 2009

Implementation date

July 1, 2009

Scope

JR/T 0052-2009 (Bank card specification) is available as an English-translated PDF.

JR/T 0052-2009 — This Standard specifies the card-face design elements, physical characteristics, card media, card-face character printing, card security requirements etc. of bank cards.

This Standard applies to all ID-1 bank cards issued within the territory of the People's Republic of China.

Found what you need?

Document preview — JR/T 0052-2009

National Standard of the People's Republic of China

ICS: 35.240.40
Classification: A 11

Issued by: People's Bank of China 3.No action is required - Full-copy of this standard will be automatically & immediatel

Foreword...3
Introduction..4
1 Scope..5
2 Normative References...5
3 Terms and Definitions...5
4 Card-face design elements...7
5 Physical characteristics of cards...8
6 Card media..9
7 Printing of characteristics on card-face...10
8 Card security requirements...11

Foreword

This Standard was proposed by People's Bank of China.

This Standard shall be under the jurisdiction of China Financial Standardization

Technical Committee.

The responsible drafting organizations of this Standard. People's Bank of China

Science and Technology Department, China Financial Computerization Corp.

The participating drafting organizations of this Standard. Industrial and Commercial

Bank of China, Agricultural Bank of China, Construction Bank of China, Hua Xia Bank,

China UnionPay Co., Ltd., National Bank Card Test Center, China Banknote Credit

Card Industry Development Co., Ltd.

1 Scope

This Standard specifies the card-face design elements, physical characteristics, card

media, card-face character printing, card security requirements etc. of bank cards.

This Standard applies to all ID-1 bank cards issued within the territory of the People's

Republic of China.

2 Normative References

The provisions in following documents become the provisions of this Standard through

reference in this Standard. For dated references, the subsequent amendments

(excluding corrigendum) or revisions do not apply to this Standard, however, parties

who reach an agreement based on this Standard are encouraged to study if the latest

versions of these documents are applicable. For undated references, the latest edition

of the referenced document applies.

GB/T 14916-2006, Identification cards - Physical characteristics (ISO/IEC

7810.2003, IDT)

GB/T 15120.1~15120.5-1994, Identification cards - Recording technique (ISO/IEC

7811-1~7811-5.1985, IDT)

GB/T 19584, Specification on magnetic stripe data content and application for bank

card

JR/T 0008, Bank identification number and card number for bank card

JR/T 0025 (all parts), China financial integrated circuit card specifications

ISO 7811-6, Identification cards - Recording technique - Part 6.Magnetic stripe -

High coercivity

3 Terms and Definitions

For the purposes of this Specification, the following terms and definitions apply.

3.1

ID-1 card

-- any picture which may cause confusion in card handling of merchants;

-- any picture which may cause bank card fraud;

-- any picture which may cause bad influences on the trademark and services of a

brand or contain hostile or sarcastic meanings.

4.2 Card front-face design elements

Card front-face design elements shall include issuing institution identification, issuing

institution name, card number, primary receiving identifier and so on. Contact-type

integrated circuit(s) cards shall also include chips.

4.3 Card back-face design elements

Card back-face design elements include magnetic stripe, signature panel and other

auxiliary information.

4.4 Other design elements

Credit cards and quasi-credit cards shall also include effective (expiry) dates,

cardholder names, fluorescent anti-counterfeit marks, holographic anti-counterfeit

labels, and first four digits of pre-printed card numbers.

5 Physical characteristics of cards

5.1 Dimensions of cards

The dimensions and tolerances of cards and the burrs on the edge of card-face shall

be as specified in GB/T 14916.

5.2 Structure of cards

Cards may comprise integral material and laminated material or glued material. Their

structure shall be as specified in GB/T 14916-2006.

5.3 Materials and characteristics of cards

The specific materials of cards shall be as specified in GB/T 14916-2006.

5.3.1 General characteristics of card materials

The general characteristics of card materials shall be as specified in GB/T 14916-2006,

except peel strength.

The peel strength of card materials refers to that all layers of materials constituting

card structure shall be glued together, each layer having the minimum peel strength of

4.5 N/cm.

6.2.1 Contact-type interfaces

The module height of contact-type chips, dimensions and positions of contacts, and

distribution of contacts as well as other contact-type chip cards shall be as specified in

JR/T 0025.3.

6.2.2 Non-contact interfaces

The non-contact chip cards shall be as specified in JR/T 0025.8.

6.2.3 Card data elements of chip cards

The data elements of cards shall be as specified in JR/T 0025.

7 Printing of characteristics on card-face

7.1 Embossing

7.1.1 Embossing content

The embossing contents preferably include.

-- card number;

-- card effective (expiry) date;

-- cardholder name, etc.

7.1.2 Embossed characters and their general requirements

The sets and fonts, character pitches and character height of characters which are

visible or machine-readable among embossed characters, and the fluctuating height

of embossed characters etc., shall be as specified in GB/T 15120.1-1194.

7.1.3 Positions of embossed characters on ID-1 cards

The content for embossed area designated of ID-1 cards includes card number, card

effective (expiry) date, cardholder name etc.; and it shall be specifically as specified in

GB/T 15120.3-1994.

7.2 Non-embossing (intaglio printing, planographic printing)

Except the embossing content specified in 7.1.1, the text information on card-face may

be printed by non-embossing (intaglio printing and planographic printing). The non-

embossed (intaglio printed or planographic printed) elements, such as card-face text

etc., shall be printed in the contrast colour to card primary colour.

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 7811

How to Download JR/T 0052-2009

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.