JJG 1082.2-2013Verification Regulation of Means of Measuring Instrument for Wheel-Diameter of Railway Locomotives and Vehicles. Part 2: Means of Measuring Tools for Wheel-Diameter (English PDF)
铁路机车车辆轮径量具检具 第2部分:轮径测量器检具
This is a limited preview
Buy now to download the full PDF (9 pages)
Need quotation for your management?
Get a formal quotation for JJG 1082.2-2013 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine
Level / Type
National · Mandatory
Issue date
January 6, 2013
Implementation date
April 6, 2013
Scope
JJG 1082.2-2013 is the English-translated version of 铁路机车车辆轮径量具检具 第2部分:轮径测量器检具.
JJG 1082.2-2013 - This standard applies to railway rolling wheel diameter gauge gage initial verification, follow-up test and use checks.
Found what you need?
Document preview — JJG 1082.2-2013
National Standard of the People's Republic of China
- ICS
- 17.040
Contents
- Introduction (II)
- 1 Scope (1)
- 2 Overview (1)
- 3 Metering performance requirements (1)
- 3.1 Measurement Block combination formula gage (1)
- 3.2 Measurement Standard arc type gages (2)
- 4 General Requirements (2)
- 5 Control of measuring instruments (2)
- 5.1 Verification Conditions (2)
- 5.2 Verification Project (3)
- 5.3 Verification Methods (3)
- 5.4 Verification Results Processing (5)
- 5.5 Test cycle (5)
- Appendix A Locomotive wheel diameter measuring gage calibration record sheet (6)
- Appendix B Calibration certificate and test results in the notice page format (7)
1 Scope (1)
2 Overview (1)
3 Metering performance requirements (1)
3.1 Measurement Block combination formula gage (1)
3.2 Measurement Standard arc type gages (2)
4 General Requirements (2)
5 Control of measuring instruments (2)
5.1 Verification Conditions (2)
5.2 Verification Project (3)
5.3 Verification Methods (3)
5.4 Verification Results Processing (5)
5.5 Test cycle (5)
Appendix A Locomotive wheel diameter measuring gage calibration record sheet (6)
Appendix B calibration certificate and test results in the notice page format (7)
Introduction
JJG 1082 "railway rolling stock wheel diameter measuring gage" consists of two parts.
--- Part 1. round foot diameter gage;
--- Part 2. wheel diameter measuring gage.
When using this procedure in Railway Locomotive wheel diameter measuring gage calibration, this subject should be selected according to the type of gage Procedures set the appropriate section.
This section is about the contents of wheel diameter measuring gage measurement verification, according JJF1002-2010 "National Measurement Unit Setting rules to write rules ", JJG 1081.2-2013" railway rolling stock wheel diameter measuring diameter measurement - Part 2 "And other requirements compiled.
This procedure was first formulated.
Railway rolling stock wheel diameter measuring gages test procedures Part 2. wheel diameter measuring gage
1 Scope
The order applies to railway rolling stock wheel diameter measuring gage initial verification, use and subsequent verification check.
2 Overview
Railway rolling stock wheel diameter measuring gage (hereinafter referred to as "measuring gage") for verification Locomotive wheel diameter Indication error of measuring devices, including standard arc two forms and seized a quantity of a combination of block-type gage.
Standard arc type gages by an arcuate circular surface, lateral positioning surface and base composition.
The combined amount of the seizure by a precision-block cylinder chord gauge blocks, bow high in blocks, spacers, and base plate and other combinations to make. It works for the V-groove diameter measuring method, the diagram shown in Figure 1.
Figure 1 - Block seized a combined amount of work Schematic
3 metering performance requirements
3.1 Measurement combination formula Gage Block
3.1.1 Surface roughness 3.1.1.1 surface roughness Ra of the upper cylinder precision cylindrical surface is 0.4µm.
3.1.1.2 surface roughness Ra of the upper gauge block measuring surface is 0.08µm.
3.1.2 Precision cylinder diameter and cylindricity Cylindricity Precision Cylindrical should be less than 0.002mm.
The nominal value of two precision cylindrical diameter of d0 = 61mm, given its actual value, the diameter difference should be less than 0.004mm.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.
How to Download JJG 1082.2-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JJG 1082.1-2013 — Verififcation Regulation of Means of Measuring Instrument for Wheel-Diameter of Railway Locomotives and Vehicles. Part 1: Means of Ruler for Wheel-Diameter
JJG 1151-2025 — Verification Regulation of Liquid Chromatograph-Atomic Fluorescence Spectrometers
JJG 1204-2025 — Verification Regulation of Electronic Price Computing Scales(for Trial Implementation)
JJG 1082.2-2013
$195.00