JJG 1082.1-2013Verififcation Regulation of Means of Measuring Instrument for Wheel-Diameter of Railway Locomotives and Vehicles. Part 1: Means of Ruler for Wheel-Diameter (English PDF)
铁路机车车辆轮径量具检具 第1部分:轮径尺检具
This is a limited preview
Buy now to download the full PDF (8 pages)
Need quotation for your management?
Get a formal quotation for JJG 1082.1-2013 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine
Level / Type
National · Mandatory
Issue date
January 6, 2013
Implementation date
April 6, 2013
Scope
JJG 1082.1-2013 is the English-translated version of 铁路机车车辆轮径量具检具 第1部分:轮径尺检具.
JJG 1082.1-2013 - This standard applies to railway rolling wheel diameter feet first test gages, follow-up test and use checks.
Found what you need?
Document preview — JJG 1082.1-2013
National Standard of the People's Republic of China
- ICS
- 17.040
Contents
- Introduction (II)
- 1 Scope (1)
- 2 Overview (1)
- 3 Metering performance requirements (1)
1 Scope (1)
2 Overview (1)
3 Metering performance requirements (1)
Surface roughness 3.1 (1) Straightness 3.2 dipstick (1)
3.3 Measuring tape jaws two parallel measuring surface (1)
3.4 Measuring tape mark width (1)
3.5 Measuring tape indication error (1)
3.6 the amount of rod length and the amount of change (1)
4 General Requirements (2)
4.1 Appearance (2)
4.2 Interaction of each part (2)
5 Control of measuring instruments (2)
5.1 Verification Conditions (2)
5.2 Verification Project (3)
5.3 Verification Methods (3)
5.4 Test results processing (4)
5.5 Test cycle (4)
Appendix A foot diameter wheel railway vehicles seized a test record sheet (5)
Appendix B calibration certificate and test results in the notice page format (6)
Introduction
JJG 1082 "railway rolling stock wheel diameter measuring gage" consists of two parts.
--- Part 1. round foot diameter gage;
--- Part 2. wheel diameter measuring gage.
When using this procedure in Railway Locomotive wheel diameter measuring gage calibration, this Regulation should be selected according to the type of gage Cheng corresponding portions.
This part of the contents on foot diameter wheel gage verification, according JJF1002-2010 "national verification regulations Cheng write rules ", JJG 1081.1-2013" railway rolling stock wheel diameter measuring Part 1. round foot diameter "and to Seeking compiled.
This procedure was first formulated.
Railway rolling stock wheel diameter measuring gages test procedures Part 1. round foot diameter gage
1 Scope
The order applies to railway rolling stock wheel foot diameter gage initial verification, use and subsequent verification check.
2 Overview
Indication foot diameter wheel railway vehicles Gage (hereinafter referred to as round foot diameter gage) is used to test Locomotive wheel diameter feet Error and center of the probe positioned at a distance to the surface, where the left and right wheel diameter measuring tape to measure the scale center of the probe to the vertical positioning block Straight from the positioning surface. Wheel diameter gage foot structure is shown in Figure 1.
Figure 1 foot diameter gage structure diagram
1- floor; 2,3,4,5-foot diameter wheel positioning block; 6- the right foot box; 7- left foot box; 8- left measuring tape; 9- left cursor;
10,13,17- dipstick positioning block; 11- left locking screw; 12- right locking screw; 14- and right cursor; 15- the right measuring tape;
16- dipstick; 18- limit screw 3 metering performance requirements 3.1 surface roughness Face positioning block surface roughness Ra measuring tape and the upper limit is 0.8µm. Surface roughness measuring rod end face Ra upper limit is 0.4µm.
Straightness of 3.2 dipstick Straightness measuring rod should be less than 0.1mm.
3.3 measuring tape jaws two parallel measuring surface Measuring tape jaws two parallel measuring surface should be less than 0.01mm.
3.4 mark width measuring tape Measuring tape main scale and vernier mark width of 0.08mm ~ 0.18mm, the width of the difference should be less than 0.05mm.
3.5 indication error measuring tape Left and Right indication error measuring tape should not exceed ± 0.04mm.
3.6 the amount of rod length and the amount of change Given the amount of the actual value of the length of the rod. Its length fluctuation amount dipstick should meet the requirements in Table 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 8 pages — is available in the English PDF.
How to Download JJG 1082.1-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JJG 1082.2-2013 — Verification Regulation of Means of Measuring Instrument for Wheel-Diameter of Railway Locomotives and Vehicles. Part 2: Means of Measuring Tools for Wheel-Diameter
JJG 1151-2025 — Verification Regulation of Liquid Chromatograph-Atomic Fluorescence Spectrometers
JJG 1204-2025 — Verification Regulation of Electronic Price Computing Scales(for Trial Implementation)
JJG 1082.1-2013
$165.00