JJF 1900-2021Calibration Specification for Verification Instruments of Parking Timers (English PDF)
停车场电子计时装置检定仪校准规范
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JJF 1900-2021 in 30 minutes.
Issued by
State Administration for Market Regulation
Level / Type
National · Mandatory
Issue date
February 23, 2021
Implementation date
August 23, 2021
Scope
JJF 1900-2021 is the English-translated version of 停车场电子计时装置检定仪校准规范.
JJF 1900-2021 is the Chinese standard "Calibration Specification for Verification Instruments of Parking Timers". Issued on 2021-02-23, in force from 2021-08-23.
Found what you need?
Document preview — JJF 1900-2021
Contents
- Introduction (II)
- 1 Scope (1)
- 2 Reference documents (1)
- 3 Overview (1)
- 4 Measurement characteristics (2)
- 4.1 Current moment (2)
- 4.2 Second pulse (2)
- 4.3 Internal crystal oscillator (2)
- 4.4 Time interval(2)
- 5 Calibration conditions (2)
- 5.1 Environmental conditions (2)
- 5.2 Measurement standards and other equipment (2)
- 6 Calibration items and calibration methods (2)
- 6.1 Calibration items (2)
- 6.2 Calibration method (3)
- 7 Calibration result expression (5)
- 8 Recalibration interval (6)
- Appendix A Calibration Record Format (7)
- Appendix B Internal page format of calibration certificate (9)
- Appendix C Example of Uncertainty Evaluation of Calibration Results (10)
1 Scope (1)
2 Reference documents (1)
3 Overview (1)
4 Measurement characteristics (2)
4.1 Current moment (2)
4.2 Second pulse (2)
4.3 Internal crystal oscillator (2)
4.4 Time interval(2)
5 Calibration conditions (2)
5.1 Environmental conditions (2)
5.2 Measurement standards and other equipment (2)
6 Calibration items and calibration methods (2)
6.1 Calibration items (2)
6.2 Calibration method (3)
7 Calibration result expression (5)
8 Recalibration interval (6)
Appendix A Calibration Record Format (7)
Appendix B Internal page format of calibration certificate (9)
Appendix C Example of Uncertainty Evaluation of Calibration Results (10)
Introduction
This specification is based on JJF 1071-2010 "Rules for the Compilation of National Metrology and Calibration Specifications", JJF 1001-2011 "Tong Compiled with Metrological Terms and Definitions and JJF 1059.1-2012 "Evaluation and Expression of Measurement Uncertainty".
This specification is released for the first time.
Calibration specification for parking lot electronic timing device verifier
1 Scope
This specification applies to the calibration of the parking lot electronic timing device verifier.
2 Reference documents the following documents are cited in this specification.
JJF 1180 Time-frequency measurement terms and definitions for dated reference documents, only the dated version applies to this specification; for all undated references the latest version (including all amendments) is applicable to this specification.
3 overview
The parking lot electronic timing device verifier (hereinafter referred to as the "verifier") is used to calibrate the electronic parking meter toll Meters and metering devices for parking lot electronic timing toll devices.
The verifier provides Micro Motion by receiving Global Navigation Satellite System (GNSS) satellite signals and decoding time information Accurate current time, and synchronize the local clock. When the GNSS satellite signal is not locked, the verifier will the previous time is provided by the local clock. The control unit of the verifier sends or receives a certain time interval through the sensor unit Start-stop signal, the time interval is measured by the timing unit to realize the verification of the timing error of the electronic timing device of the parking lot.
At the same time, the control unit outputs the time interval at the "timing signal output terminal".
The sensor units mainly include. manual start-stop keyboard, radio frequency controller, geo-sensing parking simulator and geomagnetic vehicle simulation
Figure 1 Block diagram of the verification instrument
1PPS-second pulse signal output terminal; T-timing signal output terminal; f-internal crystal oscillator frequency signal output terminal
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
How to Download JJF 1900-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JJF 2425-2026 — Calibration specification for carbon dioxide incubators
JJF 1183-2025 — Calibration Specification for Temperature Transmitters
JJF 1282-2025 — Calibration Specification for Time Delay Relays
JJF 1900-2021
$300.00