JJF 1408-2013Calibration Specification for Articulated Arm Coordinate Measuring Machines (English PDF)
关节臂式坐标测量机校准规范
This is a limited preview
Buy now to download the full PDF (13 pages)
Need quotation for your management?
Get a formal quotation for JJF 1408-2013 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine
Level / Type
National · Mandatory
Issue date
May 13, 2013
Implementation date
August 13, 2013
Scope
JJF 1408-2013 is the English-translated version of 关节臂式坐标测量机校准规范.
JJF 1408-2013 - This standard applies to calibrate articulated arm coordinate measuring machine.
Found what you need?
Document preview — JJF 1408-2013
National Standard of the People's Republic of China
- ICS
- 17.040
Contents
- Introduction (II)
- 1 Scope (1)
- 2. References (1)
- 3 Terms (1)
- 4 Overview (1)
- 5 Metrological characteristics (2)
- 5.1 Single-axis coordinate measuring consistency (2)
- 5.2 Spatial length indication error (2)
1 Scope (1)
2 References (1)
3 Terms (1)
4 Overview (1)
5 Metrological characteristics (2)
5.1 Single-axis coordinate measuring consistency (2)
5.2 Spatial length indication error (2)
Calibration Condition 6 (2)
6.1 Environmental conditions (2)
6.2 Main calibration equipment and requirements (2)
7 Calibration items and methods (3)
7.1 Single-axis coordinate measuring consistency (3)
7.2 Spatial length indication error (4)
8 Calibration results (5)
9 Recalibration interval (5)
Appendix A single-point calibration probe recommended specific methods (6)
Appendix B Calibration recording format include (7)
Appendix C shows the length of the measuring arm space Error Uncertainty Evaluation (11)
Appendix D measurement process (13) does not meet the requirements of
Introduction
The specification for the first time to develop. The main basis for performance measurement and calibration methods ASMEB89.4.22 "articulated arm CMM performance evaluation methods "(MethodsforPerformanceEvaluationofArticulatedArm CoordinateMeasuringMachines) were prepared.
Articulated arm coordinate measuring machine calibration specification
1 Scope
This standard applies to the calibration of articulated arm coordinate measuring machine.
2. References
This specification refers to the following documents.
JJF 1071-2010 National Calibration Specifications writing rules ASMEB89.4.22 articulated arm coordinate measuring machine performance evaluation method (MethodsforPerformance EvaluationofArticulatedArmCoordinateMeasuringMachines) for dated references, only the dated edition applies to this specification; undated reference documents Member, the latest edition (including any amendments) applies to this specification.
3 Terms
3.1 club standardbar, balbar the amount of two or more of the same diameter as a standard ball by the rigid connecting rod composed regulation.
Note. center club length is the standard length ball center of the space. Reference ASMEB89.4.22.
4 Overview
Articulated arm coordinate measuring machine, also known as portable 3D measuring arm, crank-type coordinate measuring machine (hereinafter referred to as the measurement arm). Measurement is based on the rotation arm joints and rotating arm coordinate measurement system by the angle at each joint compilation Angle encoder measurement information obtained through the coordinate transformation to obtain the coordinates of the probe in the instrument coordinate system.
Measuring arm joints generally consists of three components, namely, shoulder, elbow and wrist, shoulder should include A and B Shaft, including the D shaft elbow, wrist and includes E and F shaft. Probe is mounted on a shaft final, Achieved by manual measurements. Common 5-axis measuring arm, 6-axis and 7-axis several configurations, 1 to 4 FIG.
Figure 12-1-2 constructed by ABDEF rotation axis configuration according to FIG 22-2-2 ABCDEF rotation axis
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 13 pages — is available in the English PDF.
How to Download JJF 1408-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JJF 2425-2026 — Calibration specification for carbon dioxide incubators
JJF 1183-2025 — Calibration Specification for Temperature Transmitters
JJF 1282-2025 — Calibration Specification for Time Delay Relays
JJF 1408-2013
$255.00