Valid

JJF 1394-2013Calibration Specification for Wireless Network Testers (English PDF)

无线路测仪校准规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (34 pages)

Need quotation for your management?

Get a formal quotation for JJF 1394-2013 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine

Level / Type

National · Mandatory

Issue date

February 16, 2013

Implementation date

May 16, 2013

Scope

JJF 1394-2013 is the English-translated version of 无线路测仪校准规范.

JJF 1394-2013 - This standard applies to GSM and CDMA wireless router wireless router measuring instrument measuring instrument calibration.

Found what you need?

Document preview — JJF 1394-2013

National Standard of the People's Republic of China

ICS
17.220

Contents

  • Introduction (II)
  • 1 Scope (1)
  • 2. References (1)
  • 3 Terminology and units of measurement (1)
  • 3.1 Error Vector Magnitude (1)

1 Scope (1)

2 References (1)

3 Terminology and units of measurement (1)

3.1 Error Vector Magnitude (1)

Phase error 3.2 (1)

Waveform quality 3.3 (1)

3.4 Broadcast Control Channel (2)

3.5 Traffic Channel (2)

3.6 Access probe (2)

4 Overview (2)

5 Metrological characteristics (2)

5.1 Frequency Range (2)

5.2 Emission level (2)

5.3 Emission spectrum (2)

5.4 the transmission modulation (3)

5.5 Reception level (3)

6 Calibration conditions (3)

Environmental conditions 6.1 (3)

6.2 Standards and other measuring equipment (3)

7 Calibration items and calibration methods (4)

7.1 Appearance and working properly check (4)

7.2 GSM Wireless Road Tester (4)

7.3 CDMA Wireless Road Tester (7)

8 Calibration results expression (9)

9 Recalibration interval (10)

Appendix A calibration record form (11)

Appendix B Calibration Certificate page format (19)

Evaluation of Uncertainty Appendix C Examples (27) Appendix D frequency and channel number corresponding to the table (37)

Introduction

This specification based JJF 1071-2010 "National Calibration Specifications writing rules" and JJF 1059-1999 "test Evaluation and Expression of Uncertainty "preparation, calibration specification Wireless Road Tester include GSM (GlobalSystemof MobileCommunication) wireless channel measuring instrument and CDMA (CodeDivisionMultipleAccess) Wireless Road Measuring instrument.

This specification, emission levels, emission spectrum and calibration method for transmitting modulated reference YDC023-2006 "800MHzCDMA1X Digital Cellular Mobile Telecommunication Network Test Methods. Part 1 Basic mobile no Line indicators, functionality and performance, "and YD/T 1215-2006" 900/1800MHzTDMA digital cellular mobile communication Letter Network General Packet Radio Service (GPRS) device Test Method. The mobile station "in the relevant content.

This specification is the first release.

Wireless Drive Test Calibration Specification

1 Scope

This calibration specifications for GSM and CDMA wireless channel measuring instrument wireless road test instrument calibration.

2. References

This specification refers to the following documents.

YDC023-2006 800MHzCDMA1X Digital Cellular Mobile Telecommunication Network Test Method. The mobile station Part 1 Basic indicators of wireless features and performance YD/T 1215-2006 900/1800MHzTDMA digital cellular mobile telecommunication network Packet Radio Service (GPRS) device testing method. the mobile station for dated references, only the dated edition applies to this specification; undated reference documents Member, the latest edition (including any amendments) applies to this specification.

3 terminology and units of measurement 3.1 error vector magnitude, EVM on the vector coordinates (Figure 1), with the decline due to the interference of non-linear RF amplifier noise, transmission channel Down, etc., so that the amplitude and phase of a vector to produce changes in the measured magnitude of the vector difference vector and the reference vector. That A scalar quantity, is usually expressed as a percentage of the peak value of the reference vector.

Figure 1 error vector

3.2 phase error in the digitally modulated carrier signal, the carrier phase to form a string of symbols of the track phase, the phase of each symbol Difference between the regression line. In degrees (°).

3.3 waveform quality Applied to the CDMA system metrics, it is related to the ratio of power to total power; power is usually associated it is calculated from the measured cross-correlation signal with a known coding as a reference baseband signals obtained.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 34 pages — is available in the English PDF.

How to Download JJF 1394-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
34 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JJF 1394-2013

$650.00