JJF 1377-2012Calibration Specification for Wheel Alignment Testers of Level Type (English PDF)
水准式车轮定位测量仪校准规范
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JJF 1377-2012 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine
Level / Type
National · Mandatory
Issue date
December 12, 2012
Implementation date
March 12, 2013
Scope
JJF 1377-2012 is the English-translated version of 水准式车轮定位测量仪校准规范.
JJF 1377-2012 - This standard applies to leveling type wheel alignment measuring instrument (hereinafter referred to as wheel alignment) calibration.
Found what you need?
Document preview — JJF 1377-2012
Contents
- Introduction (II)
- 1 Scope (1)
- 2. References (1)
- 3 Terminology and units of measurement (1)
- 3.1 Vehicle support plane (1)
- 3.2 Longitudinal symmetry plane of the vehicle (1)
- 3.3 Camber (1)
1 Scope (1)
2 References (1)
3 Terminology and units of measurement (1)
3.1 Vehicle support plane (1)
3.2 Longitudinal symmetry plane of the vehicle (1)
3.3 Camber (1)
Within 3.4 kingpin inclination (2)
3.5 Caster angle (2)
3.6 Toe (2)
4 Overview (3)
5 Metrological characteristics (3)
6 Calibration conditions (4)
Environmental conditions 6.1 (4)
6.2 Calibration standard (4)
7 Calibration items and calibration methods (4)
7.1 Leveling Calibration (4)
7.2 Calibration turntable (7)
7.3 Calibration toe feet (7)
8 Calibration results expression (8)
9 Recalibration interval (8)
Appendix A scale factor derivation etatheta (9)
Appendix B at right angles to the auxiliary seat specific requirements (11)
Appendix C calibration certificate (within the page) content (12)
Appendix D standard type wheel alignment measuring instrument calibration records (13)
Evaluation of Uncertainty Appendix E standard formula wheel alignment measuring instrument level measuring indication error (14)
Introduction
In the present specification JJF 1071-2010 "National Calibration Specifications writing rules", JJF 1001-2011 "Universal Measurement terms and definitions ", JJF 1059-1999" Evaluation and Expression of Uncertainty in Measurement "as the basic norms into series Row developed.
The main reference specification GB/T 3730.3-1992 "motor vehicles and trailers of terms and their definitions vehicle size" JJG (car) 03-1995 "standard wheel locator (provisional)", "automobile test" (Shanghai science and technology Surgery Literature Publishing House) compiled.
The specification for the first time to develop.
Leveling type wheel alignment gauge calibration specification
1 Scope
This specification applies to the standard-type wheel alignment measuring instrument (hereinafter referred to as wheel alignment instrument) calibration.
2. References
GB/T 3730.3-1992 vehicles and trailers of terms and their definitions vehicle size for dated references, only the dated edition applies to this specification; undated reference documents Member, the latest edition (including amendments) apply to this specification.
3 terminology and units of measurement GB/T 3730.3-1992 defined and the following terms and definitions apply to this specification.
3.1 vehicle support plane supportingplaneofvehicle [GB/T 3730.3-1992,2.1] when the parameters used to measure the size of the vehicle, the supporting wheels flat, solid level. Acronym X plane.
3.2 vehicle longitudinal plane of symmetry longitudinalplaneofsymmetryofvehicle [GB/T 3730.3-1992,2.4] Vertical line bisecting plane AB. Points A and B at both ends of the shaft through the wheel axis of the same plane X Vertical plane through the line of intersection with the wheel center plane delta and X plane intersection (see Figure 1). Acronym Y plane.
Figure 1 vehicle longitudinal plane of symmetry
3.3 camber camberangle [GB/T 3730.3-1992,3.25] in over the wheel axis X and perpendicular to the plane of the plane, and the horizontal axis between the wheel sandwiched acute angle. Figure 2 as shown by the symbol alpha expressed in degrees (°).
Figure 2 camber
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
How to Download JJF 1377-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JJF 2425-2026 — Calibration specification for carbon dioxide incubators
JJF 1183-2025 — Calibration Specification for Temperature Transmitters
JJF 1282-2025 — Calibration Specification for Time Delay Relays
JJF 1377-2012
$315.00