Valid

JJF 1373-2012Calibration Specification for Dynamic Elastic Modulus Measurement Instruments (English PDF)

动弹仪校准规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (11 pages)

Need quotation for your management?

Get a formal quotation for JJF 1373-2012 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine

Level / Type

National · Mandatory

Issue date

December 12, 2012

Implementation date

March 12, 2013

Scope

JJF 1373-2012 is the English-translated version of 动弹仪校准规范.

JJF 1373-2012 - This standard applies to move meter (also known as dynamic elastic modulus tester) calibration.

Found what you need?

Document preview — JJF 1373-2012

Contents

  • Introduction (III)
  • 1 Scope (1)
  • 2. References (1)
  • 3 Terminology and units of measurement (1)
  • 4 Overview (2)
  • 5 Metrological characteristics (2)
  • 5.1 Transmitting frequency error (2)
  • 5.2 Frequency measurement error (2)
  • 5.3 Repeatability (2)
  • 5.4 Dynamic elastic modulus error (2)

1 Scope (1)

2 References (1)

3 Terminology and units of measurement (1)

4 Overview (2)

5 Metrological characteristics (2)

5.1 Transmitting frequency error (2)

5.2 Frequency measurement error (2)

5.3 Repeatability (2)

5.4 Dynamic elastic modulus error (2)

Calibration Condition 6 (2)

6.1 Environmental conditions (2)

6.2 Calibration with standard equipment and ancillary equipment (2)

7 Calibration items and calibration methods (3)

7.1 Calibration items (3)

7.2 Calibration method (3)

8 Calibration results expression (5)

8.1 Calibration Data Processing (5)

8.2 Calibration certificate (5)

8.3 Calibration of Uncertainty Evaluation (5)

9 Recalibration interval (6)

Appendix A recommended calibration certificate content and in-page format (7)

Appendix B to move frequency measurement instrument calibration error Uncertainty Evaluation Examples (9)

Introduction

In the present specification JJF 1071 "National Calibration Specifications writing rules", JJF 1001 "universal metering and fixed term Justice "and JJF 1059" Evaluation and Expression of Uncertainty in Measurement "as the basis of specifications developed series.

This specification primarily with reference to GB/T 50082-2009 "ordinary concrete long-term performance and durability test method standard Accurate "and DL/T 5150-2001" hydraulic concrete testing procedures "and compiled.

The specification for the first time to develop.

Calibration Specification for move

1 Scope

This instruction applies to move instrument (also known as dynamic elastic modulus analyzer) calibration.

2. References

This specification refers to the following documents.

JJG233-2008 piezoelectric accelerometer JJG834-2006 Dynamic Signal Analyzer JJF 1001 common measurement terms and definitions JJF 1156-2006 vibration, shock, speed measurement terms and definitions GB/T 50082-2009 ordinary concrete long-term performance and durability test method standards DL/T 5150-2001 hydraulic concrete testing procedures for dated references, only the dated edition applies to this specification; undated reference documents Member, the latest edition (including any amendments) applies to this specification.

3 terminology and units of measurement JJF 1001-2011, JJF 1156-2006, GB/T 50082-2009 and DL/T 5150-2001 in the community and given the following terms and definitions apply to this specification.

Dynamic elastic modulus by the power law principle, according to elastic wave propagation velocity in the object of the modulus of elasticity measured.

Note. The dynamic modulus of elasticity can be divided into horizontal longitudinal dynamic elastic modulus and dynamic elastic modulus.

Lateral dynamic elastic modulus by the equation (1) is calculated.

Edt = kdtWL3f2/a4 (1) where.

Edt -- lateral dynamic elastic modulus, GPa;

a -- test block square cross-section side length, mm;

L -- test block length, mm;

W -- quality test block, kg;

f -- specimen resonance frequency of the lateral vibration, Hz;

kdt -- lateral dynamic elastic modulus calculation constants, kdt = 13.244 × 10-7.

Longitudinal dynamic elastic modulus by the equation (2) is calculated.

Edl = kdlWLf2/a2 (2) where.

Edl -- longitudinal dynamic elastic modulus, GPa;

a -- test block square cross-section side length, mm;

L -- test block length, mm;

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.

How to Download JJF 1373-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
11 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JJF 1373-2012

$255.00