JB/T 11131-2011Fluorinated ethylene propylene (FEP) resin for wires and cables (English PDF)
电线电缆用聚全氟乙丙烯树脂
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 11131-2011 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
May 18, 2011
Implementation date
August 1, 2011
Scope
JB/T 11131-2011 is the English-translated version of 电线电缆用聚全氟乙丙烯树脂.
JB/T 11131-2011 is a recommended Chinese machinery industry standard on fluorinated ethylene propylene resin, FEP, intended for wires and cables. It divides the product into categories, states what it is used for, and then sets the requirements, the test methods, the inspection rules and the provisions for marking, packaging, storage and transport.
The material it applies to is FEP resin supplied in granular form for wire and cable manufacture. Among the standards it quotes are GB/T 1033.1-2008, GB/T 1408.1-2006, GB/T 1409-2006, GB/T 3682-2000, GB/T 7141-2008 and HG/T 2904-1997.
The resin is classified K15 in the Chinese system and 29.035.20 in the international one.
Found what you need?
Document preview — JB/T 11131-2011
National Standard of the People's Republic of China
- ICS
- 29.035.20
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- 1 Scope
- 2 Normative references
1 Foreword
JB/T 11131-2011 was issued by MIIT on 18 May 2011 and has been in force since 1 August 2011.
2 Scope
This standard is a recommended Chinese machinery industry standard on fluorinated ethylene propylene resin, FEP, intended for wires and cables. It divides the product into categories, states what it is used for, and then sets the requirements, the test methods, the inspection rules and the provisions for marking, packaging, storage and transport. The material it applies to is FEP resin supplied in granular form for wire and cable manufacture. Among the standards it quotes are GB/T 1033.1-2008, GB/T 1408.1-2006, GB/T 1409-2006, GB/T 3682-2000, GB/T 7141-2008 and HG/T 2904-1997. The resin is classified K15 in the Chinese system and 29.035.20 in the international one.
3 Normative references
JB/T 11131-2011 cites the following standards, which apply in full or in part through the references made to them in its clauses.
GB/T 1033.1-2008 — Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pycnometer method and titration method
GB/T 1408.1-2006
GB/T 1409-2006 — Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
GB/T 1842-2008 — Plastics -- Test method for environmental stress-cracking of polyethylene
GB/T 3682-2000 — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
GB/T 6678-2003 — General principles for sampling chemical products
GB/T 6679-2003 — General rules for sampling solid chemical products
GB/T 7141-2008 — Plastics -- Methods of heat aging
GB/T 8170-2008 — Rules of rounding off for numerical values & expression and judgement of limiting values
HG/T 2904-1997
SN/T 2004.1-2005
SN/T 2004.2-2005
SN/T 2005.2-2005
4 About this standard
Issued by: MIIT
English translation: about 15 pages
5 Classification and status
International classification (ICS): 29.035.20
Prefix JB/T: recommended standard.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 1033.1-2008Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pycnometer method and titration method
- GB/T 1408.1-2006Insulating materials -- Test methods for electric strength -- Part 1: Test at power frequencies
- GB/T 1409-2006Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
- GB/T 1842-2008Plastics -- Test method for environmental stress-cracking of polyethylene
- GB/T 3682-2000Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
- GB/T 6678-2003General principles for sampling chemical products
SN/T 2004.1-2005 · SN/T 2004.2-2005 · SN/T 2005.2-2005
Similar standards
How to Download JB/T 11131-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 1033.1-2008 — Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pycnometer method and titration method
GB/T 1409-2006 — Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
GB/T 1842-2008 — Plastics -- Test method for environmental stress-cracking of polyethylene
Secure payment via Stripe
Payments accepted
JB/T 11131-2011
$105.00