JB/T 10619-2006Chromium-free zinc-aluminium flake coatings - Technical requirements (English PDF)
无铬锌铝涂层 技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 10619-2006 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
September 14, 2006
Implementation date
March 1, 2007
Scope
JB/T 10619-2006 is the English-translated version of 无铬锌铝涂层 技术条件.
JB/T 10619-2006 is the Chinese standard "Free chromate Zn-Al flake coatings - Specification". Its scope clause reads: This standard specifies the technical requirements and test methods for free chromate Zn-Al flake coatings (hereinafter referred to as coatings) on steel parts and components.
Its clauses include terms and definitions; information that the buyer shall provide to the supplier; markings; technical requirements; sampling; test method. It was issued by the National Development and Reform Commission on SEPTEMBER 14, 2006 and took effect on MARCH 01, 2007.
Found what you need?
Document preview — JB/T 10619-2006
National Standard of the People's Republic of China
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword3
- Introduction4
- 1 Scope5
- 2 Normative references5
- 3 Terms and definitions5
- 4 Information that the buyer shall provide to the supplier6
- 5 Markings6
- 5.1 Overview6
- 5.2 Examples6
- 6 Technical requirements6
- 6.1 Appearance6
- 6.2 Coating grade, coating amount, coating thickness7
- 6.3 Adhesion strength7
- 6.4 Salt spray corrosion resistance7
- 6.5 Water resistance7
- 6.6 Damp heat resistance8
- 6.7 Heat resistance8
- 6.8 Hardness8
- 7 Sampling8
- 8 Test method8
- 8.1 Appearance8
- 8.2 Test of coating amount9
- 8.3 Adhesion strength test9
- 8.4 Salt spray test9
- 8.5 Water resistance test10
- 8.6 Damp heat test10
- 8.7 Heat resistance test10
- 8.8 Hardness test10
- Appendix A (Informative) Calculation method of coating surface area11
1 Scope
This standard specifies the technical requirements and test methods for free chromate Zn-Al flake coatings (hereinafter referred to as coatings) on steel parts and components.
2 Normative references
The provisions in following documents become the provisions of this Standard through reference in this Standard. For the dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Standard; however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies.
GB/T 1727 General preparation of paint film
GB/T 5270 Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings - Revies of methods available for testing adhesion (GB/T 5270-2005, ISO 2819:1980, IDT)
GB/T 6462 Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (GB/T 6462-2005, ISO 1463:2003, IDT)
GB/T 6739 Determination of film hardness by pencil test (GB/T 6739-1996, eqv JIS K5400:1990)
GB/T 10125 Corrosion tests in artificial atmospheres - Salt spray tests (GB/T 10125-1997, eqv ISO 9227:1990)
3 Terms and definitions
The following terms and definitions apply to this standard.
3.1 Free chromate Zn-Al flake coatings
The anti-corrosion coating with scaly zinc as the main component, which is formed by dipping, brushing, spraying water-based free chromate Zn-Al paints on the surface of steel parts or components, through baking.
a) The standard number.
b) The grade of coating required for the part to be coated.
d) Requirements for additional coatings, such as sealers, friction reducers, colours.
5 Markings
5.1 Overview
The coating is indicated by the element symbol "Zn" (zinc) plus the prefix 'fl' (flake) and the suffix "nc" (chromium-free). If it is required to indicate the technical requirements in a detailed manner, it shall indicate the coating thickness behind "fl Zn".
5.2 Examples
5.2.1 The coating, whose minimum salt spray test time is 480 h, is marked as flZn 480 nc.
5.2.2 The coating, whose minimum salt spray test time is 720h and the minimum thickness is 8 µm, is marked as flZn 720 8µm nc.
6 Technical requirements
4 Information that the buyer shall provide to the supplier
c) The final heat treatment temperature of the workpiece to be coated. Since the coating is baked at a temperature of about 300 °C, the purchaser shall consider whether this temperature affects the mechanical properties of the coated workpiece.
6.1 Appearance
6.1.1 The basic color of the coating is silver-gray. Other colors and anti-friction properties of the coating can be obtained, by adding additional coatings or adding appropriate additives to the coating.
6.1.2 The coating shall be continuous, without defects such as holiday, blisters, peeling, cracks, pitting, inclusions. The coating shall be uniform, without obvious local over-thickness. Coatings allow slight color differences. in 6.3.
6.6 Damp heat resistance
The coating shall be subjected to the damp heat resistance test, according to the method specified in 8.6; the red rust shall not appear within 360 hours.
6.7 Heat resistance
The heat resistance test of the coating is carried out, according to the method specified in 8.7. The coating is required to have no defects, such as discoloration, blisters, peeling, cracks. After the heat resistance test, the coating performance shall still meet the technical requirements specified in 6.3 and 6.4.
6.8 Hardness
The hardness test shall be carried out in accordance with the provisions of 8.8. The hardness of the coating shall not be lower than 7H.
7 Sampling
7.1 From the same batch of products, randomly take three specimens for each test. Carry out the test. If any one of the specimens is unqualified after the test, randomly take three more specimens for the same test. If one of them is unqualified, this batch of products is unqualified.
7.2 For assemblies or parts or components whose individual mass exceeds 150 g, cut a part of the workpiece as a specimen for testing. In order to prevent the exposed steel substrate, at the incision, from affecting the test results, it shall use paint, wax or adhesive tape to protect the incision. The same method can also be used to prepare specimens, for parts with complex shapes and difficult to calculate the surface area.
8 Test method
8.1 Appearance
Under natural scattered light, visually inspect the appearance of the coating with the naked eye or corrected vision.
8.2 Test of coating amount
8.2.1 Dissolution weighing method
For specimen which has a mass greater than 50 g, use a balance with an accuracy of 1 mg to obtain the original mass W1 (unit in mg). Place the specimen in 20% NaOH aqueous solution at 70 °C ~ 80 °C; soak for 10 min to dissolve the free chromate zinc-flake coating. Take out the specimen. Use water to wash it thoroughly. Dry it immediately. Then weigh the mass W2 (unit in mg) of the specimen after the coating is dissolved. Measure and calculate the surface area S of the workpiece (unit in dm2).
Calculate the amount of coating Ws (unit in mg/dm2), according to the following formula:
Refer to Appendix A, for the calculation method of coating surface area of commonly used parts.
Note 1: If the mass of the specimen is less than 50 g, several specimens shall be accumulated to reach a total mass of more than 50 g; then the coating amount test shall be carried out.
Note 2: After the free chromate Zn-Al flake coating is immersed in NaOH solution for 10 minutes, if the coating is not completely dissolved, the soaking time shall be extended, until the coating is completely dissolved.
8.2.2 Metallographic microscopy
According to the requirements of GB/T 6462, the thickness of the coating is detected by metallographic microscopy.
8.3 Adhesion strength test
The adhesive tape test method is used to detect the adhesion strength between the free chromate Zn-Al flake coating and the substrate. The adhesive tape test is carried out, in accordance with the requirements of GB/T 5270.
8.4 Salt spray test
The salt spray test is carried out, according to the neutral salt spray test requirements, which are specified in GB 10125. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 1727General methods for preparation of coating films
- GB/T 5270Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings - Review of methods available for testing adhesion
- GB/T 6462Metallic and oxide coatings - Measurement of coating thickness - Microscopical method
- GB/T 6739Paints and varnishes - Determination of film hardness by pencil test
- GB/T 10125Corrosion tests in artificial atmospheres - Salt spray tests
Similar standards
How to Download JB/T 10619-2006
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10125-1988 — Corrosion tests in artificial atmosphere--Salt spray tests (SS tests)
GB/T 10125-1997 — Corrosion tests in artificial atmospheres--Salt spray tests
GB/T 10125-2012 — Corrosion tests in artificial atmospheres - Salt spray tests
JB/T 10619-2006
$135.00