JB/T 10216-2013Cable trays for electrical control and distribution (English PDF)
电控配电用电缆桥架
This is a limited preview
Buy now to download the full PDF (23 pages)
Need quotation for your management?
Get a formal quotation for JB/T 10216-2013 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
December 31, 2013
Implementation date
July 1, 2014
Scope
JB/T 10216-2013 is the English-translated version of 电控配电用电缆桥架.
JB/T 10216-2013 is the Chinese standard "Cable trays for electrical control and distribution". Its scope clause reads: This standard specifies terms and definitions, model code, structure requirements, test methods, inspection rules, marking, transport and storage of cable support system for electric control distribution.
This standard is applicable to cable supports system for indoor and outdoor high-and-low voltage power transmission and distribution engineering of industrial and civil buildings. Its clauses include terms and definitions.
Found what you need?
Document preview — JB/T 10216-2013
National Standard of the People's Republic of China
- Replacing
- JB/T 10216-2000
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword i
- 1 Scope
- 2 Normative References
- 3 Terms and Definitions
- 3.1 Terms and Definitions
- 3.2 Model Code
- 4 Structure Requirements
- 4.1 Normal Service Conditions
- 4.2 Special Service Conditions
- 4.3 Structure Requirements of Cable Support System
- 5 Test Methods
- 5.1 Inspection on Appearance and Dimensional Accuracy
- 5.2 Mechanical Load Test
- 5.3 Impact Test
- 5.4 Artificial Climate Protection Test
- 5.5 Performance Test for Various Surface Protective Layers
- 5.6 Protection Circuit Continuity Test
- 5.7 Protection Grade Test
- 5.8 Fire Resistance Grade Test for Fire-resistant Cable Support System
- 6 Inspection Rules
- 6.1 Inspection Classification
- 6.2 Type Inspection
- 6.3 End-of-manufacturing Inspection
- 6.4 Sampling and Judgment
- 7 Marking, Transport and Storage
- 7.1 Marking and Nameplate
- 7.2 Transport and Storage
- Annex A (Informative) Typical Legend of Tray and Ladder
- Annex B (Informative) Schematic Diagram for Typical Supports and Pendants
- Annex C (Informative) Use Recommendation under Different Environments for Cable Supports System
- Figure 1 Layout Form for the Load Test of Straight Sections
- Figure 2 Layout Form for the Load Test of Joint of Straight Section
- Figure 3 Typical Test Layouts for Bends
- Figure 4 Typical Positioning Modes for Fixing Body of Test Supports and Tested Supports and Pendants
- Figure 5 Test Sample Layout Drawing for Impact Test
- Figure 6 Layout Drawing for Electrical Continuity Test
- Figure 7 Installation Diagram for Support System in the Furnace
- Figure 8 Schematic Diagram for Cable Laying in Fire-resistant Cable Support System
- Figure 9 Wiring for Fire Resistance Test of Power Cable
- Figure 10 Wiring for Fire Resistance Test of Control Cable
- Figure A.1 Solid Bottom Cable Tray Length
- Figure A.2 Perforated Cable Tray Length
- Figure A.3 Cable Tray of Assembly Length
- Figure A.4 Mesh Cable Tray Length
- Figure A.5 Cable Ladder Length
- Figure A.6 Double-side Cable Supports System Length
- Figure B.1 Typical Supports and Pendants
- Table 1 Support System Main Structure Material and Code
- Table 2 Structural Feature Code
- Table 3 Codes of Main Varieties
- Table 4 Cable Support System Protection Type and Corresponding Service Environment Condition Grade
- Table 5 Fire Resistance Class and Code of Fire-resistant Cable Support System
- Table 6 Parameters of Different Climatic Environment Grades
- Table 7 Parameters of Different Chemical Corrosion Environments
- Table 8 Recommended Common Specifications and Dimensions
- Table 9 Permissible Minimum Plate Thickness of Support System
- Table 10 Technical Requirements of Surface Protective Layer
- Table 11 Safe Working Load (SWL) of Typical Cable Support System
- Table 12 Artificial Climate Test Items and Test Periods
- Table 13 Performance Test Items for Various Surface Protective Layers
- Table C.1 Use Recommendation under Different Environments for Cable Supports System
1 Scope
This standard specifies terms and definitions, model code, structure requirements, test methods, inspection rules, marking, transport and storage of cable support system for electric control distribution.
This standard is applicable to cable supports system for indoor and outdoor high-and-low voltage power transmission and distribution engineering of industrial and civil buildings.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 12-2013 Cup Head Square Neck Bolts
GB/T 93-1987 Single Coil Spring Lock Washers, Normal Type
GB/T 97.1-2002 Plain Washers - Product Grade A
GB/T 700-2006 Carbon Structural Steels
GB 912-2008 Hot-rolled Sheets and Strips of Carbon Structural Steels and High Strength Low Alloy Structural Steels
GB/T 1408.1-2006 Electrical Strength of Insulating Materials - Test Methods - Part 1: Tests at Power Frequencies
GB/T 1410-2006 Methods of Test for Volume Resistivity and Surface Resistivity of Solid Electrical insulating Materials
GB/T 1720-1979 Method of Test for Adhesion of Paint Films
GB/T 1804-2000 General Tolerances - Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications
GB/T 2423.4-2008 Environmental Testing for Electric and Electronic Products - Part 2: Test Method - Test Db: Damp Heat, Cyclic ( 12h+12h Cycle)
GB/T 2423.17-2008 Environmental Testing for Electric and electronic Products - Part 2: Test Method - Test Ka: Salt Mist
GB/T 2423.55-2006 Environmental Testing for Electric and Electronic Products - Part 2 : Test Methods - Test Eh: Hammer Tests
GB/T 2573-2008 Test Method for Aging Properties of Glass Fiber Reinforced Plastics
GB/T 3280-2007 Cold Rolled Stainless Steel Plate Sheet and Strip
GB/T 3857-2005 Test Method for Chemical Resistance of Glass Fiber Reinforced Thermosetting Plastics
GB/T 3880.1-2006 Wrought Aluminium and Aluminium Alloy Plates, Sheets and Strips for General Engineering - Part 1: Technical Conditions of Delivery
GB 4208-2008 Degrees of Protection Provided by Enclosure (IP Code)
GB/T 4956-2003 Non-magnetic Coatings on Magnetic Substrates - Measurement of Coating Thickness - Magnetic Method
GB/T 5270-2005 Metallic Coatings on Metallic Substrates - Electrodeposited and Chemically Deposited Coatings - Revies of Methods Available for Testing Adhesion
GB/T 5780-2000 Hexagon Head Bolts - Product Grade C
GB/T 6170-2000 Hexagon Nuts, Style 1
GB/T 6892-2006 Wrought Aluminium and Aluminium Alloys Extruded Profiles for General Engineering
GB 7251.1-2013 Low-voltage Switchgear and Controlgear Assemblies - Part 1: General Rules
GB/T 8013.1-2007 Anodic Oxide Coating and Organic Polymer Coatings on Aluminium and Its Alloys - Part 1: Anodic Oxide Coatings
GB/T 8237-2005 Liquid Unsaturated Polyester Resin for Fiber Reinforced Plastics
GB 8624-2012 Classification for Burning Behavior of Building Materials and Products
GB/T 9978.1-2008 Fire-resistance Tests - Elements of Building Construction - Part 1: General Requirements
GB/T 10580-2003 Standard Conditions for Use Prior to and During the Testing of Solid Insulating Materials
GB/T 11253-2007 Cold-rolled Sheets and Strips of Carbon Structural Steels
GB/T 13452.2-2008 Paints and Varnishes - Determination of Film Thickness
GB 14907-2002 Fire Resistive Coating for Steel Structure
GB/T 18369-2008 Glass Fiber Roving
GB/T 18370-2001 Glass Fibre Woven Roving
GB/T 21762-2008 Cable Management - Cable Tray Systems and Cable Ladder Systems
GB/T 23639-2009 Energy Conservation and Corrosion-resistant Steel-made Cable Support System
JB/T 6743-1993 Corrosion-resistant Environmental Technical Requirements for Indoor and Outdoor Steel-made Cable Support System
3 Terms and Definitions
3.1 Terms and Definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1 cable supports system
full name of rigid structure system for supporting cable, which consists of straight segment, bend, system accessory as well as supports and pendants of cable tray or cable ladder (it is called support system for short)
3.1.2 cable tray
assembly composed of base plate and side plate which forms a whole together with the base plate or is connected to the base plate […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 47322-2026Test method for the fire resistance of cables under the elevated temperature conditions of a building fire
- NB/T 10292-2019Aluminium alloy cable tray system
- NB/T 20348-2015Technical specification for installation and test of containment instrumentation system of PWR nuclear power plants
- YC/T 307-2009Standard to inspection-acceptance of the installation engineering for the cigarette carton picking and sorting system
Similar standards
Editions of JB/T 10216
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 10216-2013 | Cable trays for electrical control and distribution | current edition | Current |
| JB/T 10216-2000 | Cable trays for electrical control and distribution | previous edition | Superseded |
This page sells the current edition, JB/T 10216-2013. Earlier editions are listed for reference only.
How to Download JB/T 10216-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 10062-2026 — Probes used in ultrasonic flaw detection - Testing methods for performance
JB/T 10096-2026 — Cases for power semiconductor devices - Selection guidance
JB/T 10097-2026 — Case for power semiconductor device
JB/T 10216-2013
$335.00