Valid

HG/T 5459-2018Pyrolysis carbon black from waste tyres (English PDF)

废旧轮胎裂解炭黑

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for HG/T 5459-2018 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

October 22, 2018

Implementation date

April 1, 2019

Scope

HG/T 5459-2018 is the English-translated version of 废旧轮胎裂解炭黑.

HG/T 5459-2018 is the Chinese standard "Waste tire pyrolysis carbon black". Its scope clause reads: This Standard specifies the designation, technical requirements, test methods, inspection rules and packaging, marking, storage and transportation requirements for waste tire pyrolysis carbon black.

This Standard applies to the carbon black produced through pyrolysis such as thermal medium and microwave, using waste tire as the raw material. Its clauses include terms and definitions; designation; technical requirements; inspection rules; packaging, marking, storage and transportation.

It was issued by the Ministry of Industry and Information Technology of P. R. China on OCTOBER 22, 2018 and took effect on APRIL 01, 2019.

Found what you need?

Document preview — HG/T 5459-2018

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword3
  • 1 Scope4
  • 2 Normative references4
  • 3 Terms and definitions4
  • 4 Designation5
  • 5 Technical requirements5
  • 6 Inspection rules6
  • 7 Packaging, marking, storage and transportation8

1 Scope

This Standard specifies the designation, technical requirements, test methods, inspection rules and packaging, marking, storage and transportation requirements for waste tire pyrolysis carbon black.

This Standard applies to the carbon black produced through pyrolysis such as thermal medium and microwave, using waste tire as the raw material.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 3780.1, Carbon black - Part 1: Test method for iodine adsorption number

GB/T 3780.2, Carbon black - Part 2: Determination of oil absorption number

GB/T 3780.5, Carbon black - Part 5: Determination of specific surface area - CTAB test method

GB/T 3780.8, Carbon black - Part 8: Determination of heating loss

GB/T 3780.12, Carbon black - Part 12: Inspection of impurity material

GB/T 3780.15, Carbon black - Part 15: Determination of light transmittance of toluene extract

GB/T 3780.18, Carbon black - Part 18: Standard test methods for evaluation in Natural Rubber (NR)

GB/T 3780.21, Carbon black - Part 21: Determination of sieve residue - Water flushing method

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Waste tire pyrolysis carbon black

6 Inspection rules

6.3.1.2 Sampling tube, whose main part shall be a rigid plastic or stainless-steel tube; sealing plate, a rubber plate, whose inner hole is slightly smaller than the outside diameter of the main tube and where axial movement is allowed along the main tube. Or other material proven to be equally applicable.

6.3.2 Sample container

A screw-top wide-mouth bottle capable of holding 2 kg of carbon black samples or other containers that do not contaminate carbon black.

6.3.3 Total sampling quantity

Not less than 2 kg (including reserved samples).

6.3.4 Sampling method

Carbon black in bags: Open the suture hole of the carbon black bag; carefully remove about 100 mm of the carbon black on the surface; use a sampling spoon to take samples in the sample container by equal amount of each unit; sew the packaging bag mouth after sampling. Alternatively, put the carbon black bag flat; clean the packaging part where samples shall be taken; insert the sampling tube, with the diagonal end upward, into the required place in the packaging bag, so that the carbon black flows through the tube into the sample bottle; after a sufficient quantity is taken, put the carbon black bag flat; pull out the sampling tube; close the sampling mouth.

Note: For a test of pelletization of palletized carbon black, samples should be taken carefully so as to avoid breaking carbon black particles.

6.3.5 Sample label

Label the wall of container immediately after the samples are placed in it. The contents of the label include:

-- sample name and sample number;

-- batch number and quantity of general materials;

-- production unit;

-- sampling method;

-- sampling volume;

-- sampling date;

-- sampler.

6.3.6 Sample preservation

6.3.6.1 Samples should be stored in the sample room where temperature and humidity are appropriate.

6.3.6.2 The effective storage period of the sample shall be 6 months.

6.4 Acceptance

6.4.1 Acceptance of products shall be carried out according to the regulations of ex-factory inspection.

6.4.2 The acceptance period shall be 30 days after the products arrive at the place of receipt agreed upon by the supplier and the buyer.

7 Packaging, marking, storage and transportation

7.1 Packaging

7.1.1 At the end of the production process, the product should be properly packaged.

For small packaging bags, the net content of each package should be 20 kg or 25 kg.

For packages with unit weight of more than 100 kg, such as container bags, the weight accuracy should be within ±0.7% of the total weight.

7.1.2 Product packaging materials must be resistant to moisture and pollution, and shall be marked conspicuously.

7.1.3 Structure of packaging bag:

-- The inner bag is three layers of 80 g/m² kraft paper, and the outer bag is a plastic woven bag coated with a layer of plastic film on the inner wall;

-- The inner bag is three layers of 80 g/m² kraft paper, and the outer bag is two layers of 80 g/m² kraft paper;

-- Automatic packaging bag for automatic packaging machine, both inner and outer layers of which are 80 g/m² kraft paper;

-- Other packaging in line with user requirements.

7.1.4 Suture and suture materials of packaging bag:

-- cotton thread or synthetic fiber thread suture material;

-- appropriate adhesive for adhesion;

-- thermo-compression (suture should be adopted for the inner bag);

-- vacuum automatic sealing. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download HG/T 5459-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

HG/T 5459-2018

$115.00