HG/T 4670-2014Determination of black specks and off-colour specks in flame retardants for plastics modification (English PDF)
改性塑料用阻燃剂黑点和异色点的测定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for HG/T 4670-2014 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
October 14, 2014
Implementation date
April 1, 2015
Scope
HG/T 4670-2014 is the English-translated version of 改性塑料用阻燃剂黑点和异色点的测定.
HG/T 4670-2014 is the chemical industry standard for determining black specks and off-colour specks in flame retardants used to modify plastics. It sets out two procedures: method A, wet sieving, intended for flame retardant powders that are sticky, and method B, dry sieving, for powders that are not adhesive.
The choice between them therefore depends on how the powder behaves, and the result describes the cleanliness of the flame retardant rather than its performance in fire.
Test sieves conform to GB/T 6003.1. The document is classified G31 in the Chinese system and 83.040.30 internationally. Issued on 14 October 2014, it has applied since 1 April 2015.
Found what you need?
Document preview — HG/T 4670-2014
National Standard of the People's Republic of China
- ICS
- 83.040.30
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- [Preview only]
- 1 Scope
- 2 Normative References
- 3 Terms and definitions
- 3.1 Category A
- 3.2 Category B
- 4 Classification and designation
- 4.1 General
- 4.2 Character group 1
- 4.3 Character group 2
- 4.4 Character group 3
- 4.5 Character group 4
- 4.6 Designation example
- 5 Test Methods
- 5.1 Appearance requirements
- 5.2 Technical requirements
- 5.3 Environmental requirements
- 6.1 Test conditions
- 6.2 Test substrate
- 6.3 Apparatus
- 6.4 Appearance
- 6.5 Coating property
- 6.6 Shear elongation
- 6.7 Tensile shear strength
- 6.8 Tensile bond strength
- 6.9 Free formaldehyde
- 7 Inspection rules
- 7.1 Inspection
- 7.2 Batching
- 7.3 Sampling
- 7.4 Judgment of inspection results
- 8 Marking, packaging, transportation and storage
- 8.1 Marking
- 8.2 Packaging
- 8.3 Transportation
- 8.4 Storage
- 9 Packaging, transportation and storage
1 Foreword
HG/T 4670-2014 was issued by Ministry of Industry and Information Technology of the People's Republic of China on 14 October 2014 and has been in force since 1 April 2015.
The HG/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.
The document runs to 15 pages in English translation.
2 Scope Preview
This standard is the chemical industry standard for determining black specks and off-colour specks in flame retardants used to modify plastics. It sets out two procedures: method A, wet sieving, intended for flame retardant powders that are sticky, and method B, dry sieving, for powders that are not adhesive. The choice between them therefore depends on how the powder behaves, and the result describes the cleanliness of the flame retardant rather than its performance in fire. Test sieves conform to GB/T 6003.1. The document is classified G31 in the Chinese system and 83.040.30 internationally.
HG/T 4670-2014 falls under ICS 83.040.30, in the field of rubber and plastics industries.
This catalogue holds 313 other HG/T standards in that field.
In this catalogue, HG/T standards carry edition years from 1975 to 2026.
3 Normative references
GB/T 6003.1
4 About this standard
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
English translation: about 15 pages
5 Related standards
Standards on related subjects:
GB/T 3681.1-2021 — Plastics - Methods of exposure to solar radiation - Part 1: General guidance
GB/T 3960-2016 — Plastics—Test method for friction and wear by sliding
GB/T 3682-2000 — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
HG/T 6500-2026 — Determination of phenolic hydroxyl groups in epoxy resin - Spectrophotometric method
HG/T 6499-2026 — Plastics - General requirements for recyclability design of plastic products
HG/T 4574-2014 — Polyurethane material-Determination of foam reaction characteristic
6 Classification and status
International classification (ICS): 83.040.30
Chinese Standard Classification (CCS): G 31
Prefix HG/T: recommended standard.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download HG/T 4670-2014
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 6003.1-1997 — Test sieves of metal wire cloth
GB/T 6003.1-2012 — Test sieves - Technical requirements and testing - Part 1: Test sieves of metal wire cloth
GB/T 6003.1-2022 — Test sieves—Technical requirements and testing—Part 1:Test sieves of metal wire cloth
HG/T 4670-2014
$55.00