Valid

GB/Z 37551.3-2024Marine energy - Wave, tidal and other water current converters - Part 3: Measurement of mechanical loads (English PDF)

海洋能 波浪能、潮流能及其他水流能转换装置 第3部分:机械载荷测量

Preview PDF

This is a limited preview

Buy now to download the full PDF (69 pages)

Need quotation for your management?

Get a formal quotation for GB/Z 37551.3-2024 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

August 23, 2024

Implementation date

August 23, 2024

Scope

GB/Z 37551.3-2024 is the English-translated version of 海洋能 波浪能、潮流能及其他水流能转换装置 第3部分:机械载荷测量.

GB/Z 37551.3-2024 is the Chinese guidance document on measuring mechanical loads on marine energy converters that harness waves, tidal streams and other water currents, modified from IEC TS 62600-3:2020.

It sets requirements for site and object selection, measured load cases in steady operation, transient events and abnormal conditions, capture matrices, measured parameters and test equipment.

Calibration of load and non-load channels, data verification, processing with rainflow counting, equivalent fatigue loads and power spectral density, uncertainty assessment and reporting are also covered.

Separate provisions apply to converters with rotors, and normative annexes treat full-scale structural laboratory testing of rotor blades and blade test loads. It was issued on 23 August 2024.

Found what you need?

Document preview — GB/Z 37551.3-2024

National Standard of the People's Republic of China

ICS
27.140
Classification
F 14

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Preface
  • Introduction
  • 1 Scope
  • 1.1 Overview
  • 1.2 Classification of Ocean Energy Conversion Devices (MEC)
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Symbols, subscripts and abbreviations
  • 4.1 Symbols
  • 4.2 Subscript
  • 4.3 Abbreviations
  • 5 General
  • 5.1 Document Structure
  • 5.2 Security of the testing process
  • 5.3 Technical appraisal
  • 5.4 Load measurement
  • 6 Test Requirements
  • 6.1 Overview
  • 6.2 Requirements for testing sites for wave energy conversion devices and water flow energy conversion devices
  • 6.3 Indoor load test of subsystem or structural component
  • 6.4 Measured load conditions for all wave energy converters and current energy converters
  • 6.4.1 General
  • 6.4.2 Measurement load cases in steady-state operation
  • 6.4.3 Measuring load cases during transient events
  • 6.4.4 Dynamic characteristics
  • 6.4.5 Abnormal operating conditions
  • 6.4.6 Capture Matrix
  • 6.5 Measurement load cases for ocean energy conversion devices with impellers
  • 6.5.1 Overview
  • 6.5.2 Dynamic characteristics
  • 6.5.3 Capture Matrix
  • 6.6 Measured parameters of wave energy conversion devices and water flow energy conversion devices
  • 6.6.1 Overview
  • 6.6.2 Load parameters
  • 6.6.3 Meteorological and hydrological parameters
  • 6.6.4 Operating parameters of ocean energy conversion devices
  • 6.7 Parameter Measurement of Ocean Energy Conversion Device with Impeller
  • 6.7.1 Overview
  • 6.7.2 Load parameters
  • 6.7.3 Meteorological and hydrological parameters
  • 6.7.4 Operating parameters of ocean energy conversion devices
  • 6.8 Changes in configuration of ocean energy conversion devices
  • 7 Test Equipment
  • 7.1 Load parameters of wave energy conversion devices and water flow energy conversion devices
  • 7.1.1 Overview
  • 7.1.2 Sensor types
  • 7.1.3 Selection of sensor installation location
  • 7.1.4 Connection between energy capture device and energy extraction system
  • 7.1.5 Connections between energy extraction systems and substructure and/or foundations
  • 7.1.6 Connection of energy extraction system to floating body
  • 7.1.7 Mooring positioning loads
  • 7.1.8 Absolute and relative positions of energy capture devices
  • 7.1.9 Absolute and relative positions of energy extraction systems
  • 7.1.10 Absolute and relative positions of foundations or floating bodies
  • 7.1.11 Water pressure measurement
  • 7.2 Operating parameters of wave energy conversion devices and water flow energy conversion devices
  • 7.2.1 Overview
  • 7.2.2 Electric power
  • 7.2.3 Hydraulic power
  • 7.2.4 Generator speed
  • 7.2.5 Braking torque or braking force
  • 7.2.6 Status of ocean energy conversion devices
  • 7.2.7 Braking status
  • 7.2.8 Draft or freeboard
  • 7.3 Load measurement of ocean energy conversion devices with impellers
  • 7.3.1 Overview
  • 7.3.2 Bending moment at blade root
  • 7.3.3 Blade bending moment distribution
  • 7.3.4 Blade torsion frequency/damping
  • 7.3.5 Impeller yaw and pitch moments
  • 7.3.6 Impeller torque
  • 7.3.7 Pillar bending moment
  • 7.3.8 Darrieus-type impeller bending moment
  • 7.3.9 Absolute and relative position measurement of power extraction system (PTO) and its blades
  • 7.4 Measurement of operating parameters of ocean energy conversion devices with impellers connected to the shaft
  • 7.4.1 Overview
  • 7.4.2 Impeller speed or generator speed
  • 7.4.3 Convective bias
  • 7.4.4 Impeller azimuth
  • 7.4.5 Pitch angle position
  • 7.4.6 Pitch rate
  • 7.4.7 Braking torque
  • 7.5 Oceanographic and meteorological parameters
  • 7.5.1 Overview
  • 7.5.2 Measurement and installation requirements
  • 7.5.3 Sea (River) Ice Load and Ice Accumulation Intensity
  • 7.6 Data Acquisition System
  • 7.6.1 Overview
  • 7.6.2 Resolution and sampling frequency
  • 7.6.3 Anti-aliasing
  • 8 Determination of calibration coefficients
  • 8.1 General Principles
  • 8.2 Overview
  • 8.3 Calibration of load channels for wave energy conversion devices and water flow energy conversion devices
  • 8.4 Calibration of non-loaded channels of wave energy conversion devices and water flow energy conversion devices
  • 8.5 Load channel calibration of ocean energy conversion devices with impellers
  • 8.5.1 Overview
  • 8.5.2 Blade bending moment calibration
  • 8.5.3 Spindle torque calibration
  • 8.5.4 Pillar bending moment calibration
  • 8.6 Calibration of the non-loaded channel of an ocean energy conversion device with an impeller
  • 8.6.1 Pitch angle
  • 8.6.2 Impeller azimuth
  • 8.6.3 Yaw angle
  • 8.6.4 Oceanography and meteorology
  • 8.6.5 Braking torque or force
  • 9 Data Verification
  • 9.1 General Principles
  • 9.2 Overview
  • 9.3 Inspection and calibration of wave energy conversion devices and water flow energy conversion devices
  • 9.4 Calibration and inspection of ocean energy conversion devices with impellers
  • 9.4.1 General Principles
  • 9.4.2 Blade bending moment
  • 9.4.3 Impeller main shaft
  • 9.4.4 Pillar
  • 10 Measurement data processing
  • 10.1 General Principles
  • 10.2 General
  • 10.3 Load
  • 10.4 Current velocity and/or sea condition trend detection
  • 10.5 Statistics
  • 10.6 Rainflow Count
  • 10.7 Accumulated Rainfall Spectrum
  • 10.8 Equivalent fatigue load
  • 10.9 Velocity or wave energy flow zones
  • 10.10 Power Spectral Density
  • 11 Uncertainty Assessment
  • 12 Report
  • Appendix A (Informative) Technical differences between this document and IEC -TS62600-3.2020 and their causes
  • Appendix B (Normative) Full-scale structural laboratory testing of impeller blades
  • Appendix C (Normative) Example coordinate system for direct-drive ocean energy conversion device
  • Appendix D (Informative) Recommendations for the design and testing of ice loads and ice accretion on ocean energy conversion devices
  • Appendix E (Informative) Offshore Load Measurement
  • Appendix F (Informative) Uncertainty Analysis
  • Appendix G (Informative) Load Model Verification
  • Appendix H (Normative) Blade Test Load Settings
  • Appendix I (Informative) Differences between blade tests under design and test load conditions
  • Appendix J (Informative) Effect of Load Cycle Number on Blade Fatigue Test
  • References

Foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1: Structure and drafting rules for standardization documents" Drafting is required.

This document is Part 3 of the "Ocean Energy Wave Energy, Tidal Current Energy and Other Water Flow Energy Conversion Devices". The following parts have been published.

---Terms for devices for converting ocean energy into wave energy, tidal energy and other water flow energy (GB /Z 37551);

--- Design requirements for marine energy systems (GB/T 41088);

--- General Guidelines for Design and Analysis of Ocean Thermal Energy Conversion Power Plants (GB /Z 43521);

--- Power quality requirements for ocean energy conversion devices (GB /Z 43464);

--- Evaluation of power generation performance of wave energy conversion devices (GB /Z 40295);

--- Assessment and characterization of wave energy resources (GB/T 39571);

--- Tidal current energy resource assessment and characterization (GB/T 39569);

--- Evaluation and characterization of river energy resources (GB /Z 43465);

---Ocean energy - Wave energy, tidal energy and other water flow energy conversion devices - Part 3: Mechanical load measurement (GB /Z 37551.3);

---Ocean energy wave energy, tidal energy and other water flow energy conversion devices Part 10: Evaluation of mooring systems for ocean energy conversion devices (GB /Z 37551.10);

---Ocean energy wave energy, tidal energy and other water flow energy conversion devices Part 102: Evaluation of wave energy using existing operational measurement data The power generation performance of the energy conversion device at another deployment location (GB /Z 37551.102).

This document is modified to adopt IEC TS62600-3:2020 "Ocean energy wave energy, tidal energy and other water flow energy conversion devices Part 3 The document type was adjusted from the IEC technical specification to my country's national standardization guidance technical document.

This document has made the following structural adjustments compared to IEC TS62600-3:2020.

--- 4.1 in Chapter 4 corresponds to 4.1 and 4.2 in IEC TS62600-3:2020, and the subsequent article numbers are moved forward. This document has many technical differences compared to IEC TS62600-3:2020.

A single vertical line (|) indicates these differences. A list of these technical differences and their reasons is given in Appendix A.

Introduction

As a marine energy conversion device widely used in public utilities and social power supply, mechanical load characteristics are an important factor in its stable operation.

This document is based on the above requirements and provides developers, manufacturers and users with Ocean energy - Guidance on the measurement of mechanical loads on devices that convert wave energy, tidal energy and other water flow energy.

Conceptually, many ocean energy conversion devices, with the exception of wave energy converters, work similarly to wind turbines.

There are few standards or technical specifications for measuring mechanical loads of energy conversion devices (including wave energy, tidal energy and other water flow energy). Therefore, it is necessary to gradually improve the Collaborate to develop detailed standards to address this issue.

In the structural design process of ocean energy conversion devices, a comprehensive understanding and accurate quantification of loads is extremely important. The relevant standards predict the loads. This document aims to.

---Standardize the measurement of mechanical loads and parameters for wave, tidal and other water flow energy conversion devices (including non-device specific parameters and non-normative parameters);

--- Establish measurement methods and application technical guidelines.

In addition to relevant definitions, normative references, symbols and units, tables, appendices and other supporting material, the core content of this document also includes The main contents will include.

---Identify characteristic parameters, define and clearly characterize the parameter values required for mechanical load measurement of ocean energy conversion devices;

--- Develop measurement procedures related to ocean energy conversion devices;

--- Outline the standardized procedures for measuring characteristic parameters, including test and measurement conditions and test equipment requirements.

This document will provide evaluation guidance for device developers and application researchers.

The "Ocean Energy Wave Energy, Tidal Energy and Other Water Flow Energy Conversion Device" is planned to consist of the following parts.

--- Part 1: Terminology. The purpose is to define the common terms in the three aspects of ocean energy conversion devices, namely, environment, technology and conversion devices.

Terms for wave energy, tidal energy and other water current energy.

--- Part 2: Design requirements for marine energy systems. The purpose is to specify wave energy, tidal energy and other water flow energy conversion device systems design requirements to ensure its engineering integrity.

--- Part 3: Mechanical load measurement. The purpose is to describe the marine energy conversion device (MEC) (including wave energy, tidal energy and other Method for measuring mechanical loads of water flow energy, specifying requirements for mechanical load measurements and full-scale structural testing of subsystems or components Require.

--- Part 4: New Technology Appraisal. The purpose is to provide the necessary practice and technical requirements for technology appraisal methods to support Requirements for the IEC RE certification process for marine renewable energy systems.

--- Part 10: Evaluation of mooring systems for marine energy conversion devices. The purpose is to specify the mooring system of floating marine energy conversion devices (MECs). Design, installation, operation, maintenance and evaluation methods of mooring systems.

--- Part 20: General guidelines for the design and analysis of ocean thermal energy conversion power plants. The purpose is to establish The general principles of pricing are presented to illustrate the design and evaluation requirements of OTEC power plants that generate stable power under various conditions.

--- Part 30: Power quality requirements. The purpose is to specify the power quality requirements of ocean energy (wave energy, tidal energy and other water flow energy) conversion devices.

Definitions, measurement procedures and evaluation methods of energy quality characteristic parameters.

--- Part 100: Evaluation of power generation performance of wave energy conversion devices. The purpose is to provide the power generation performance of wave energy conversion devices in the test field. Experimental method for evaluating power generation performance.

--- Part 101: Wave energy resource assessment and characterization. The purpose is to specify the wave energy resource assessment level and process, data collection data collection, numerical modeling, measurement-correlation-prediction methods, data analysis and preparation of technical reports for resource assessment.

--- Part 102: Evaluation of the power generation performance of a wave energy conversion device at another deployment location using existing operational measurement data.

The present invention provides a method for evaluating the power generation performance of a wave energy conversion device at another deployment site using operational measurement data from an existing site.

--- Part 103: Wave energy conversion device prototype test procedures. The purpose is to describe the wave energy conversion device prototype test procedures.

Basic test procedures and their prerequisites, test objectives, definitions, methods for processing test raw data, providing measurement sensors and Recommendations for selecting a data acquisition software package.

--- Part.200.Evaluation of the power generation performance of tidal energy conversion devices. The purpose is to provide power supply to public utilities and regional networks.

Systematic method for evaluating the power performance of tidal energy conversion equipment, definition of rated power and rated water rate of tidal energy conversion equipment, tidal Specifications for methods of drawing power performance curves for energy conversion equipment and related result reporting frameworks.

--- Part.201.Tidal energy resource assessment and characterization. The purpose is to provide analysis and description based on estimates or direct measurements. Methods for theoretical tidal current energy resources.

--- Part 202: Tidal current energy conversion device pre-prototype test procedures. The purpose is to specify the maximum Basic testing procedures and their prerequisites, test objectives, definitions, methods of processing test raw data.

--- Part 300: Evaluation of power generation performance of river energy conversion devices. The purpose is to propose a system for evaluating the power generation performance of river energy conversion devices.

The evaluation method provides a scientific method and basis for the evaluation of the power generation performance of river energy conversion devices.

--- Part 301: River energy resource assessment and characterization. The purpose is to describe the method of determining theoretical river energy resources to ensure To ensure consistency and accuracy of resource assessments. To define feasible data collection methods and/or modeling techniques for river energy resource assessments. and a framework for reporting results.

1 Scope

1.1 Overview

This document describes a method for measuring mechanical loads on marine energy conversion devices (MECs) that include wave energy, tidal energy and other water current energy.

The method specifies the requirements for mechanical load measurement, including. site selection, object selection, data collection, calibration, data verification, load measurement process, etc. conditions, capture matrices, post-processing, uncertainty calculations, and reporting requirements.

This document also provides informative annexes that can also be used for other purposes of mechanical load measurement, such as statistical analysis of measured loads, design loads, etc.

Direct measurement of loads, safety and functional testing or measurement of component loads.

The test requirements of this document are applicable to specific ocean energy conversion devices through technical qualification.

This document also specifies the requirements for full-scale structural testing of subsystems or components, with a particular focus on full-scale structural testing of MEC impeller blades.

This document focuses on the tests related to the assessment of the structural integrity of the blade to confirm that the Test whether the entire installation and production of the blade meets the design requirements.

1.2 Classification of ocean energy conversion devices (MEC)

Marine energy conversion devices (MEC) include wave energy conversion devices (WEC), tidal energy conversion devices (TEC) and other water flow energy conversion devices.

The above devices are divided into two types. base type and floating type. The energy conversion principle of TEC and other CEC is similar to that of wind turbine.

In the process of structural design of ocean energy conversion devices, a comprehensive understanding and accurate understanding of the loads is required.

It is extremely important to accurately quantify the loads and to collaboratively develop detailed criteria during the design phase to address load prediction issues.

All wave energy and current energy conversion devices can be subdivided into bottom-mounted type (see Figure 1) and floating type (see Figure 2). The following subsystems are composed of.

a) Energy capture device;

b) Power Take-off (PTO);

c) control systems;

d) Foundation and/or substructure.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 69 pages — is available in the English PDF.

Similar standards

How to Download GB/Z 37551.3-2024

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
69 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/Z 37551.3-2024

$1,100.00