Valid

GB/Z 3222.3-2026Acoustics - Description, measurement and assessment of environmental noise - Part 3: Objective method for the measurement of prominence of impulsive sounds and for adjustment of LAeq (English PDF)

声学 环境噪声的描述、测量与评价 第3部分:脉冲声显著度测量和等效连续A声级修正的客观法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/Z 3222.3-2026 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

February 27, 2026

Implementation date

February 27, 2026

Scope

GB/Z 3222.3-2026 is the English-translated version of 声学 环境噪声的描述、测量与评价 第3部分:脉冲声显著度测量和等效连续A声级修正的客观法.

GB/Z 3222.3-2026 is Part 3 of the Chinese series on describing, measuring and assessing environmental noise, and is identical to ISO/PAS 1996-3:2022.

It describes an objective way to measure how prominent impulsive sounds are and to turn that prominence into an adjustment of the A-weighted equivalent continuous sound level, LAeq, typically between 0.0 dB and 9.0 dB.

Clauses deal with the measurement itself, the prominence value P, the determination of the LAeq adjustment, the classification of impulsive sounds, accuracy and the test report.

Typical sources include compressed air releases, cargo handling, forklifts, skateboard ramps, industrial shearing, impact tools and power riveting, while gunfire, high-energy impulsive sources and occupational hearing loss are outside its scope. It supplements GB/T 3222.1 and ISO 1996-2. It was issued on 27 February 2026.

Found what you need?

Document preview — GB/Z 3222.3-2026

National Standard of the People's Republic of China

ICS
17.140
Classification
A 59

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Preface
  • Introduction
  • 1 Scope
  • 2 Normative References
  • 3 Terms and Definitions
  • 4 Measurement
  • 5 Significance, P
  • 6 Determination of LAeq Correction Amount
  • 7 Classification of Impulse Sounds
  • 8 Accuracy
  • 9 Test Reports
  • Appendix A (Informative) Research Topic
  • References

Foreword

This document is a standard or guiding technical document.

This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents". Drafting.

This document is Part 3 of GB/T (Z)3222 "Description, Measurement and Evaluation of Acoustic Environmental Noise". GB/T (Z)3222 has been... The following sections were published.

---Part 1: Basic Parameters and Evaluation Methods;

---Part 2: Sound Pressure Level Measurement;

---Part 3: Objective methods for measuring impulse saliency and correcting equivalent continuous A-weighted sound levels.

This document is equivalent to ISO /PAS 1996-3.2022 "Acoustic environment noise - description, measurement and evaluation - Part 3.impulse sound". "Objective Methods for Saliency Measurement and Equivalent Continuous A-Sound Level Correction." The document type has been changed from a publicly available ISO specification to a national standard of my country. Standardized guiding technical documents.

The following minimal editorial changes have been made to this document.

---Added note 1 to Chapter 6.

Introduction

At the same equivalent sound pressure level, noise containing significant impulse components is more annoying than continuous noise without impulse components or with modulated components.

Therefore, if significant impulse noise is present, a correction factor is usually added to the measured LAeq.

ISO 1996 provides the three most relevant impulse sound types to public reaction and their corresponding corrections. Each type is listed... Impulse sound type sound sources, but this list is not exhaustive.

This method measures the significance of impulse sounds based on their correlation with human responses, using this as a basis for objective sound source classification. This results in... The correction values can be used for sound source classification or direct application. This document describes specific methods to achieve this goal and provides guidance for the relevant authorities in classifying sound sources.

This document provides guidance on determining correction amounts. It aims to supplement the measurement methods of ISO 1996-2 used for routine environmental noise assessment.

Due to the large amount of content, GB/T (Z)3222 "Description, Measurement and Evaluation of Acoustic Environmental Noise" is proposed to consist of the following three parts.

---Part 1: Basic Parameters and Evaluation Methods. The aim is to propose basic parameters for describing environmental noise and the fundamental characteristics of environmental noise. Evaluation methods.

---Part 2: Sound Pressure Level Measurement. The purpose is to establish basic requirements for the measurement of sound pressure level - a fundamental descriptor of environmental noise. And guidelines.

---Part 3: Objective Methods for Impulse Sound Saliency Measurement and Equivalent Continuous A-Sound Level Correction. The aim is to provide objective methods for impulse sound saliency measurement.

An objective measurement method is used to classify pulse sound sources and apply them to the correction of evaluation quantities.

1 Scope

This method objectively classifies sound sources by measuring impulse saliency, with the aim of correlating it with public response. This measurement of impulse saliency... The impulse salience method is applicable to sound sources that are not identified as gunshots or high-energy pulse sounds, and typically produces a correction of 0.0 dB to 9.0 dB.

These corrections are intended to distinguish between conventional impulse sound and strong impulse sound sources, and apply the adverse corrections specified in ISO 1996-1.However... However, this correction may be used directly, as in NTACOU112[2] and BS4142[3]. ISO 1996-2 can provide a basis for carrying out this These measurements provide additional guidance.

This method aims to address typical impulse noises not classified in ISO 1996-1.Examples of noise sources include compressed air emissions, breakage points, and other sources.

The applications include. handling, cargo transportation, forklifts with clattering forks, skateboard ramps, industrial shearing, gas emission, impact dismantling tools, power riveting, and more. enumerate.

This method is not applicable to gunfire sounds. Although measurements of salience may provide relevant results, research indicates that the response to these sound sources... It may also be affected by factors beyond the scope of this document. Furthermore, this method is not applicable to high-energy pulses as explicitly specified in ISO 1996-1. Sound source.

Note: This method is not applicable to occupational hearing loss, which is beyond the scope of this document. Recommended topics for further research are listed in Appendix A.

2 Normative references

The contents of the following documents, through normative references within the text, constitute essential provisions of this document. Dated citations are not included.

For references to documents, only the version corresponding to that date applies to this document; for undated references, the latest version (including all amendments) applies. This document.

ISO 1996-1 Description, measurement and evaluation of ambient acoustics - Part 1: Basic parameters and evaluation methods (Acoustics-mentprocedures)

Note: GB/T 3222.1-2022 Acoustic ambient noise - Description, measurement and evaluation - Part 1: Fundamental parameters and evaluation methods (ISO 1996-1. 2016, IDT)

IEC 61672-1 Electroacoustics - Sound level meters - Part 1: Specification Specifications)

Note: GB/T 3785.1-2023 Electroacoustic sound level meters - Part 1: Specifications (IEC 61672-1:2013, IDT)

3 Terms and Definitions

The following terms and definitions apply to this document.

The URLs for the terminology databases maintained by ISO and IEC for standardization are as follows. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 1996-1 · IEC 61672-1

Similar standards

How to Download GB/Z 3222.3-2026

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/Z 3222.3-2026

$255.00