GB/T 9766.3-2016Test method for tyre valves -- Part 3: Test methods for snap-in valves (English PDF)
Also coversGBT9766.3-2016
This is a limited preview
Buy now to download the full PDF (7 pages)
Need quotation for your management?
Get a formal quotation for GB/T 9766.3-2016 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine
Level / Type
National · Recommended
Issue date
February 24, 2016
Implementation date
January 1, 2017
Scope
GB/T 9766.3-2016 (Test method for tyre valves -- Part 3: Test methods for snap-in valves) is available as an English-translated PDF.
GB/T 9766.3-2016 - This Part of GB/T 9766 specifies the terms and definitions, test equipment, apparatus, test device, and test procedures of snap-in valve (hereinafter referred to as "valve").
This Part is applicable to the tubeless tyre used valve test for the hand cart, motorcycle, car, light truck, and truck.
Found what you need?
Document preview — GB/T 9766.3-2016
National Standard of the People's Republic of China
- ICS
- 83.160.01
- Classification
- G 41
Issued by: General Administration of Quality Supervision, Inspection and Quarantine
Contents
- Foreword...3
- 1 Scope...5
- 2 Normative References...5
- 3 Terms and Definitions...5
- 4 Test Equipment, Apparatus...5
- 5 Test Device...6
- 6 Test Procedures...7
Foreword
GB/T 9766 Test Method for Tyre Valves can be divided into the following 7 parts.
--- Part 1. Test Methods for Clamp-In Valves;
--- Part 2. Test Methods for Rubber Base Seat Valves;
--- Part 3. Test Methods for Snap-In Valves;
--- Part 4. Test Methods for Clamp-In Tubeless Valves;
--- Part 5. Test Methods for Tyre Valves for Large Core Chamber;
--- Part 6. Test Methods for Core;
--- Part 7. Test Methods for Components.
This Part belongs to Part 3 of GB/T 9766.
This Part was drafted as per the rules specified in GB/T 1.1-2009.
This Part replaced GB/T 9766.3-2008 Test Method for Tyre Valves – Part 3. Snap-In
Valves – Test Methods; compared with GB/T 9766.3-2008, this Part has the major
technical changes as follows.
--- Increase, in the Foreword, "Part 7. Test Methods for Components" (see
Foreword);
--- Modify the scope (see Chapter 1 of this Edition; Chapter 1 of 2008 Edition);
--- Delete terms "test valves" and "aging valves" (see 3.1, 3.2 of 2008 Edition);
--- Modify pressure gauge accuracy grade (see 4.4 of this Edition; 4.4 of 2008
Edition);
--- Modify the description of test equipment in 5.2 (see 5.2 of this Edition; 5.2 of
2008 Edition);
--- Increase the test hole specification in nominal size of Phi8.8 (see Table 1);
--- Increase the provision on the reading time of rubber hardness test (see 6.1);
--- Modify the core mounting torque (see 6.3.1 of this Edition; 6.3.1 of 2008 Edition);
--- Delete the seal test of seal cap (see 6.4 of 2008 Edition);
--- Increase the provisions on bending degree of seal test on CQ07C, CQ08C valves
Test Method for Tyre Valves –
Part 3. Test Methods for Snap-in Valves
1 Scope
This Part of GB/T 9766 specifies the terms and definitions, test equipment, apparatus,
test device, and test procedures of snap-in valve (hereinafter referred to as "valve").
This Part is applicable to the tubeless tyre used valve test for the hand cart, motorcycle,
car, light truck, and truck.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB 1796.3 Tyre Valves – Part 3. Snap-In Valves (GB 1796.3-2008, ISO 9413.
1998, ISO 14960.2004, NEQ)
GB 1796.6 Tyre Valves – Part 6. Cores (GB 1796.6-2008, ISO 9413.1998, NEQ)
GB/T 12839 Terms and Definitions of Tyre Valves (GB/T 12839-2012, ISO 3877-
2.1997, NEQ)
3 Terms and Definitions
The terms and definitions stipulated in GB/T 12839 are applicable to this document.
4 Test Equipment, Apparatus
4.1 Tensile tester. load 0N~2000N, the relative change value of indicating value is
1%.
4.2 High temperature chamber. the temperature inside the chamber can reach 200°C
above, the temperature fluctuation is ±2°C.
1 – pressure regulating valve;
2 – pressure gauge.
Figure 5
6.4.2 Low temperature test
6.4.2.1 test procedures
6.4.2.1.1 Install the valve onto the test device as per the instructions in 5.2 and 5.3.
6.4.2.1.2 Place the installed valve at (-40±3) °C for at least 24h, so that ensure the
sealing area is within the test temperature.
6.4.2.1.3 At the constant pressure of (180±15)kPa, immerse the installed valve into
(-40±3) °C ethanol; the valve mouth shall be upward, the distance between valve rim
sealing part and the liquid surface shall be no greater than 100mm.
6.4.2.1.4 The valve immersed into the liquid shall be bent for 25°±3° against the valve
installing hole axis (CQ07C, CQ08C valves shall not be bent); rotate the valve around
the installing hole axis evenly for a turn within 15s~45s, and exert no torque to the
valve.
6.4.2.1.5 Repeat 6.4.2.1.3~6.4.2.1.4 with interval for at least 0.5h once, totally 5
times.
6.4.2.2 Qualification judgment
If the leakage rate is less than 0.2cm3/min, or before, in the middle, and after rotating
and bending the valve, there is no bubbles on the rim sealing place within 60s, then
the valve is judged as qualified.
NOTE. the attached gas during the installation period shall not be regarded as leakage.
6.4.3 High temperature test
6.4.3.1 Test procedures
6.4.3.1.1 Install the valve onto the test device as per the instructions in 5.2 and 5.3.
6.4.3.1.2 Place the installed valve into (100±3) °C heat-circulating air for 48h to
simulate the aging condition.
6.4.3.1.3 At the pressure of (600±15)kPa, immerse the installed valve into (66±3) °C
clean water; the valve mouth shall be upward, the distance between valve rim sealing
part and the liquid surface shall be no greater than 100mm.
6.4.3.1.4 The valve immersed into the liquid shall be bent for 25°±3° against the valve
installing hole axis (CQ07C, CQ08C valves shall bent 10°±3°); rotate the valve around
the installing hole axis evenly for a turn within 15s~45s, and exert no torque to the
valve.
6.4.3.1.5 Place the reloaded valve into the heat-circulating air again.
6.4.3.1.6 Repeat 6.4.3.1.3~6.4.3.1.5 with interval at least 0.5h once, totally 5 times;
the final bending and rotating shall be finished at the 72nd h in the test period.
6.4.3.2 Qualification judgment
If the leakage rate is less than 0.2cm3/min, or before, in the middle, and after rotating
and bending the valve, there is no bubbles on the rim sealing place within 60s, then
the valve is judged as qualified.
NOTE. the attached gas during the installation period shall not be regarded as leakage.
6.5 Assembly test
6.5.1 Pull-in force
Take water as the lubricant; install the immersed valve onto the tension tester; pull the
valve at the speed of (150±15) mm/min; stop till the marking ring of the valve body is
totally passed through the test device plate hole stipulated in 5.2; during this period,
the maximum tension is regarded as the pull-in force (see Figure 6).
6.5.2 Qualification judgment
The pull-in force shall conform to the provisions of GB 1796.3; if valve is damaged
during the test, it shall be judged as disqualified.
Appendix B
(Informative)
Technical Differences and Causes
between this Part and ISO 14960.2004
The Table B.1 gives the technical differences and causes between this Part and ISO
14960.2004.
Table B.1 Technical Differences and Causes between this Part and ISO 14960.2004
Clause No.
in this Part Technical Differences Causes
1 Modify the scope As per the requirements of GB 1796.3
2 ISO 14960.2004 quotes from ISO 3911; while this Part quotes form GB/T 12839 Quote China's terminology standard
3 ISO 14960.2004 quotes from ISO 3911; while this Part quotes form GB/T 12839 Quote China's terminology standard
3 Delete the snap-in valve definition in 3.1 of ISO 14960.2004 GB/T 12839 has such definition
3 Delete the tested valve definition in 3.2 of ISO 14960.2004 GB/T 12839 has such definition
3 Delete the aging valve definition in 3.3 of ISO 14960.2004 Don't appear in the standard
4 Add Chapter 4 Test Equipment and Apparatus
To ensure the consistency of the test
results, clearly prescribe the test
equipment and apparatus
5.2 Add the test hole with nominal dimension of Phi8.8 in test device As per the requirements of GB 1769.3
6 Delete the protective cap sealing test in 5.3 of ISO 14960.2004 GB/T 9766.7 has such provision
6.1
Add rubber hardness test
Add Figure 1 (hardness test schematic
diagram)
As per the requirements of GB 1796.3
6.2
Change the adhesive strength in 5.1 of
ISO 14960.2004 into the bonding test
between rubber and metal; add Figure 2
and Figure 3
Conform to GB 1796.3, and express
clearly
6.3 Delete the high and low temperature test against the valve and core in 5.2.3 and
ISO 14960 includes the valve and its
components test method; while China
......
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 7 pages — is available in the English PDF.
Referenced standards
Normative references
GB 1796.3 · GB 1796.3-2008 · ISO 9413 · ISO 14960.2004 · GB 1796.6 · GB 1796.6-2008 · ISO 9413.1998 · ISO 3877
How to Download GB/T 9766.3-2016
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 12839-2020 — Terms and definitions of tyre valves
GB/T 9766.1-2015 — Test method for tyre valves—Part 1: Test method for tube clamp-in valves
GB/T 9766.2-2024 — Test method for tyre valves - Part 2: Rubber base valves test method
Secure payment via Stripe
Payments accepted
GB/T 9766.3-2016
$60.00