GB/T 5704-2008Measuring instruments for anthropometry (English PDF)
人体测量仪器
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 5704-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 16, 2008
Implementation date
January 1, 2009
Scope
GB/T 5704-2008 is the English-translated version of 人体测量仪器.
GB/T 5704-2008 is the Chinese standard "Measuring instruments for anthropometry". Its scope clause reads: This standard specifies the method of direct measurement instrument commonly used anthropometric structure, measuring range, technical requirements, test procedures, and packaging and Mark.
This standard applies to human altimeter, angle gauge, caliper, tripod parallel to the regulation of design and development. Its clauses include structure type.
Found what you need?
Document preview — GB/T 5704-2008
National Standard of the People's Republic of China
- ICS
- 13.180
- Classification
- A 25
- Replacing
- GB 5704.2-1985
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Structure type
- 3.1 Human altimeter
1 Scope
This standard specifies the method of direct measurement instrument commonly used anthropometric structure, measuring range, technical requirements, test procedures, and packaging and
Mark.
This standard applies to human altimeter, angle gauge, caliper, tripod parallel to the regulation of design and development.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. Where dated references, which subsequently
Some amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Study whether the latest versions of these documents. Anyone who does not dated reference documents, the latest versions apply to this standard.
JJG30-2002 Universal caliper test procedures
3 Structure type
3.1 Human altimeter
3.1.1
Human altimeter by the ruler, fixed foot seat, activity feet seat, curved feet, the main scale rod and the base (see Figure 1).
3.1.2
main foot pole by four interconnected metal tubes (each section length 500mm) and is fixed at the first assembly of the metal tube is fixed to the top of the scale
Seat components. Each end of the metal pipe can fill an appropriately labeled, in order to connect.
3.1.3
fixed scale for the seat is fixedly mounted at the first metal pipe at the top of foot with a total first section metal pipe and fixed foot seat assembly after fixation
A length of 510mm, can be inserted or ruler bent foot fixation foot holder.
3.1.4
activities seat for the foot along the main scale bar for on-foot activities under the seat, can be inserted or ruler bent feet. Activities ruler seat has a foot-shaped frame,
On a rectangular open a small window, a small window on the edge of the foot is inserted in the active seat straightedge ruler or curved lower edge at the same level, on the edge of a small window (Measured value) position readings measured with a ruler. For ease of reading, on the seat near the fixed end of the scale a small window MARGIN painted red.
3.1.5
The two co-ruler, a ruler inserted If activities within feet seat height can be used to measure various body; If two respectively ruler
Norma and inserted into a fixed scale activities seat, when the first and second metal section of pipe used in conjunction constitute rod straight foot gauge, measure the various human width.
3.1.6
Total curved foot two, if two feet are inserted into the curved seat fixed foot foot base and activities within, the first and second metal section of the tube when in use,
That is composed of rod caliper, measure the width and thickness of the various human.
3.1.7
the main base for the foot lever to keep the ground perpendicular to the auxiliary member.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
Editions of GB/T 5704
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 5704-2008 | Measuring instruments for anthropometry | current edition | Current |
| GB 5704.2-1985 | Measuring instruments for anthropometry | previous edition | Superseded |
This page sells the current edition, GB/T 5704-2008. Earlier editions are listed for reference only.
How to Download GB/T 5704-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 5704.1-1985 — Measuring instruments for anthropometry--Anthropometer
GB/T 5704.2-1985 — Measuring instruments for anthropometry--Sliding caliper for anthropometry
GB/T 5704.3-1985 — Measuring instruments for anthropometry--Spreading caliper for anthropometry
GB/T 5704-2008
$195.00