GB/T 4706.63-2024Safety of household and similar electrical appliances - Part 63: Particular requirements for commercial electric rinsing sinks (English PDF)
家用和类似用途电器的安全 第63部分:商用电漂洗槽的特殊要求
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 4706.63-2024 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
July 24, 2024
Implementation date
August 1, 2026
Scope
GB/T 4706.63-2024 is the English-translated version of 家用和类似用途电器的安全 第63部分:商用电漂洗槽的特殊要求.
GB/T 4706.63-2024 — This chapter of GB/T 4706.1-2024 is replaced by the following. This document specifies the safety requirements for commercial electric rinse tanks.
This document applies to single-phase appliances connected to one phase and neutral line, whose rated voltage does not exceed 250V, and other appliances do not exceed 480V.
NOTE 101 These appliances are suitable for use in food businesses carried on in kitchens such as restaurants, canteens, hospitals and in commercial enterprises such as bakeries and butchers.
Processing. The electrical parts of appliances using other forms of energy are also within the scope of this document. As far as is practical, this document deals with the common hazards arising from this type of apparatus.
Note 102.Pay attention to the following. --- For equipment intended for use exclusively on vehicles, ships or aircraft, additional requirements are necessary; --- For appliances intended for use exclusively in tropical countries, special requirements are necessary; --- In many countries, additional requirements are imposed by national health, labor protection, water supply and other similar authorities.
Note 103.This document does not apply to. --- Instruments designed primarily for disinfection to clinical standards; --- Commercial dishwashers (IEC 60335-2-58); ---Appliances designed for industrial use; --- Apparatus intended for use in locations where special conditions often occur, such as the presence of corrosive or explosive atmospheres (dust, vapor or flammable gases).
Found what you need?
Document preview — GB/T 4706.63-2024
National Standard of the People's Republic of China
- ICS
- 97.040.50
- Classification
- Y 62
- Replacing
- GB 4706.63-2008
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Preface
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 General requirements
- 5 General conditions for testing
- 6 Categories
- 7 Markings and instructions
- 8 Protection against contact with live parts
- 9 Starting of electric appliances
- 10 Input power and current
- 11 Fever
- 12 Empty Chapter
- 13 Leakage current and electrical strength at operating temperature
- 14 Transient overvoltage
- 15 Moisture resistance
- 16 Leakage current and electrical strength
- 17 Overload protection of transformers and related circuits
- 18 Durability
- 19 Abnormal working conditions
- 20 Stability and mechanical hazards
- 21 Mechanical strength
- 22 Structure
- 23 Internal wiring
- 24 Components
- 25 Power connection and external cord
- 26 Terminals for external conductors
- 27 Grounding measures
- 28 Screws and connections
- 29 Clearances, creepage distances and solid insulation
- 30 Heat and flame resistance
- 31 Rust prevention
- 32 Radiation, toxicity and similar hazards
- Appendix
- Appendix N (Normative) Tracking resistance test
- Appendix P (informative) Guidelines for the application of the standard for appliances used in hot and humid climates
- Reference
Foreword
This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1: Structure and drafting rules for standardization documents" Drafting.
This document is Part 63 of GB/T 4706 "Safety of Household and Similar Electrical Appliances". GB/T 4706 has been published as follows part.
--- Part 1: General requirements;
--- Part 2: Particular requirements for electric irons;
--- Part 121: Particular requirements for professional ice cream machines.
This document replaces GB 4706.63-2008 "Particular requirements for safe commercial electric rinse tanks for household and similar electrical appliances".
Compared with GB 4706.63-2008, in addition to structural adjustments and editorial changes, the main technical changes are as follows.
--- Deleted the equipotential symbols and the requirements for adjusting different set values (see 7.6 and 19.1 of the 2008 edition);
--- Added relevant requirements for marking on appliances and instructions (see 7.12, 7.12.1, 7.12.4, 7.15 and 7.101);
--- Added the use of test probe 12 to verify access to live parts (see 8.101);
--- Added the use of specific test probes to measure the temperature of accessible surfaces (see 11.3);
--- Added the maximum temperature rise value of the specified external accessible surface under normal operating conditions (see 11.8);
--- Changed the permissible value of leakage current and defined the value for appliances with power consumption less than 1 kW (see 13.2, 13.2 of the 2008 edition);
--- Added specific requirements on the types of screws used for electrical connections and grounding continuity connections (see 28.1, 28.4);
This document is equivalent to IEC 60335-2-62:2019 "Safety of Household and Similar Electrical Appliances Part 2-62.Commercial Electric Rinse Tanks" Special Requirements for the following minimal editorial changes were made to this document.
--- The name of the standard was changed to "Safety of Household and Similar Electrical Appliances Part 63: Particular Requirements for Commercial Electric Rinsing Tanks", and the standard was strengthened.
Coordination of the quasi-system.
Introduction
GB/T 4706 "Safety of Household and Similar Electrical Appliances" adopts most of IEC 60335.On this basis, GB/T 4706 refers to the structure of IEC 60335 is divided into several parts, consisting of general requirements and special requirements. Part 1 is general requirements, and the other parts are for products covered by special requirements, their safety requirements are general requirements used in combination with the special requirements.
The requirements include supplements and modifications to the corresponding clauses in the general requirements to provide complete requirements for each product.
This document is the protection requirements for electrical, mechanical, thermal, fire and radiation risks when the appliance is used normally in accordance with the instructions.
This document also covers abnormal conditions that may occur during use and considers how electromagnetic interference may affect the safe operation of the equipment.
This document has taken into account the requirements specified in GB/T 16895 "Low Voltage Electrical Installations". The appliance is connected to the power supply in accordance with the electrical wiring rules.
requirements are coordinated.
If multiple functions of an appliance involve other parts of GB/T 4706, the other parts shall apply to the appliance separately as long as it is reasonable.
Each function. If applicable, consider the impact of one function on other functions.
When no additional requirements are given in other parts for hazards already included in this document, GB/T 4706.1 applies.
GB/T 4706 is a standard covering appliance safety and takes precedence over general standards/horizontal standards covering the same subject.
This document is used in conjunction with GB/T 4706.1-2024 "Safety of Household and Similar Electrical Appliances Part 1: General Requirements".
The part marked "applicable" in the document indicates that GB/T 4706.1-2024 "Safety of Household and Similar Electrical Appliances - Part 1: General Requirements" the corresponding clauses in the "Requirements" shall apply to this document; for the parts marked "replace" in this document, the clauses in this document shall prevail;
The "Add" part indicates that in addition to complying with the corresponding clauses in GB/T 4706.1-2024, the additional clauses in this document must also be complied with.
Clause; The part marked "modified" in this document indicates that the corresponding clauses of GB/T 4706.1-2024 are modified.
Safety of household and similar electrical appliances Part 63: Particular requirements for commercial electric rinse tanks
1 Scope
This chapter of GB/T 4706.1-2024 is replaced by the following.
This document specifies the safety requirements for commercial electric rinse tanks.
This document applies to single-phase appliances connected to one phase and neutral line, whose rated voltage does not exceed 250V, and other appliances do not exceed 480V.
NOTE 101 These appliances are suitable for use in food businesses carried on in kitchens such as restaurants, canteens, hospitals and in commercial enterprises such as bakeries and butchers.
Processing.
The electrical parts of appliances using other forms of energy are also within the scope of this document.
As far as is practical, this document deals with the common hazards arising from this type of apparatus.
Note 102.Pay attention to the following.
--- For equipment intended for use exclusively on vehicles, ships or aircraft, additional requirements are necessary;
--- For appliances intended for use exclusively in tropical countries, special requirements are necessary;
--- In many countries, additional requirements are imposed by national health, labor protection, water supply and other similar authorities.
Note 103.This document does not apply to.
--- Instruments designed primarily for disinfection to clinical standards;
--- Commercial dishwashers (IEC 60335-2-58);
---Appliances designed for industrial use;
--- Apparatus intended for use in locations where special conditions often occur, such as the presence of corrosive or explosive atmospheres (dust, vapor or flammable gases).
2 Normative references
Except for the following contents, this chapter of GB/T 4706.1-2024 applies.
Increase.
ISO 898-1 Mechanical properties of carbon steel and alloy steel fasteners Part 1: Bolts, screws and studs of specified property grades Coarse thread and fine thread (Mechanical properties of fasteners made of carbon steel and loy steel - Part 1.
Bolts,screwsandstudswithspecifiedpropertyclasses-Coarsethreadandfinepitchthread) Note. GB/T 3098.1-2010 Mechanical properties of fasteners - Bolts, screws and studs (ISO 898-1:2009, MOD) ISO 3506-1 Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Fasteners with specified grades and property levels Bolts, Screws and Studs (Fasteners-Mechanical properties of corrosion-resistant stainless steel fasteners-Part 1: Bolts,screwsandstudswithspecifiedgradesandpropertyclasses) Note. GB/T 3098.6-2023 Mechanical properties of fasteners Stainless steel bolts, screws and studs (ISO 3506-1:2020, MOD) ISO 3506-2 Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Fasteners with specified grades and property levels Nuts (Fasteners-Mechanicalpropertiesofcorrosion-resistantstainlesssteelfasteners-Part 2: Nuts withspecifiedgradesandpropertyclasses) Note. GB/T 3098.15-2023 Mechanical properties of fasteners Stainless steel nuts (ISO 3506-2:2020, MOD) ISO 3506-3 Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not subjected to tensile stress Firmware (Mechanicalpropertiesofcorrosion-resistantstainlesssteelfasteners-Part 3: Setscrewsand similarfastenersnotundertensilestress)
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 4706.1-2024Safety of household and similar electrical appliances - Part 1: General requirements
- GB/T 3098.1-2010Mechanical properties of fasteners - Bolts, screws and studs
- GB/T 3098.6-2023Mechanical properties of fasteners - Stainless steel bolts, screws and studs
- GB/T 3098.15-2023Mechanical properties of fasteners - Stainless steel nuts
ISO 898 · ISO 3506
How to Download GB/T 4706.63-2024
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 3098.1-2010 — Mechanical properties of fasteners - Bolts, screws and studs
GB/T 3098.15-2023 — Mechanical properties of fasteners - Stainless steel nuts
GB/T 3098.6-2023 — Mechanical properties of fasteners - Stainless steel bolts, screws and studs
Secure payment via Stripe
Payments accepted
GB/T 4706.63-2024
$360.00