GB/T 46059-2025Single-use rubber gloves for general applications (English PDF)
一次性使用普通用途橡胶手套
Also coversGBT46059-2025
This is a limited preview
Buy now to download the full PDF (10 pages)
Need quotation for your management?
Get a formal quotation for GB/T 46059-2025 in 30 minutes.
Issued by
State Administration for Market Regulation
Level / Type
National · Recommended
Issue date
August 29, 2025
Implementation date
September 1, 2026
Scope
GB/T 46059-2025 is the English-translated version of 一次性使用普通用途橡胶手套.
GB/T 46059-2025 — This document specifies single-use rubber products made from natural rubber latex, synthetic rubber latex, or rubber solutions for general purposes.
Physical requirements, sampling and testing methods for gloves, but excluding gloves used for medical purposes. This document does not cover the safe and proper use of gloves.
Found what you need?
Document preview — GB/T 46059-2025
National Standard of the People's Republic of China
- ICS
- 83.140.99
- Classification
- G 44
Issued by: State Administration for Market Regulation
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Requirements
- 4.1 Materials
- 4.2 Dimensions
Foreword
This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents".
Drafting.
This document is equivalent to ISO 25518:2021 "Specification for disposable general purpose rubber gloves".
The following minimal editorial changes have been made to this document.
---To align with the existing standards system, the standard name has been changed to "Disposable General Purpose Rubber Gloves".
Please note that some content in this document may involve patents. The issuing organization of this document assumes no responsibility for identifying patents.
This document was proposed by the China Petroleum and Chemical Industry Federation.
This document is under the jurisdiction of the National Technical Committee on Standardization of Rubber and Rubber Products (SAC/TC35).
1 Scope
This document specifies single-use rubber products made from natural rubber latex, synthetic rubber latex, or rubber solutions for general purposes.
Physical requirements, sampling and testing methods for gloves, but excluding gloves used for medical purposes.
This document does not cover the safe and proper use of gloves.
2 Normative references
The contents of the following documents, through normative references within the text, constitute essential provisions of this document. Dated citations are not included.
For references to documents, only the version corresponding to that date applies to this document; for undated references, the latest version (including all amendments) applies.
This document.
ISO 37 Determination of tensile stress-strain properties of vulcanized or thermoplastic rubber (Rubber, vulcanized or thermoplastic rubber) Note. GB/T 528-2009 Determination of tensile stress-strain properties of vulcanized rubber or thermoplastic rubber (ISO 37:2005, IDT) Note. GB/T 3512-2014 Accelerated aging and heat resistance test of vulcanized rubber or thermoplastic rubber in hot air (ISO 188:2011, IDT) ISO 2859-1 Sampling Procedures for Inspection by Attributes – Part 1: Sampling Schemes Indexed by Acceptable Quality Limit (AQL) for Lot-by-Lot Inspection Note. GB/T 2828.1-2012 Sampling Procedures for Inspection by Attributes - Part 1: Sampling Schemes Retrieved by Acceptable Quality Limit (AQL) (ISO) 2859-1.1999, IDT)
3 Terms and Definitions
This document does not contain any terms or definitions that need to be defined.
4 Requirements
4.1 Materials
Gloves should be made of suitable materials. Any pigments, surface treatment agents, lubricants, or powders used in the glove manufacturing process should be non-toxic.
The information should be disclosed as required. Because it is easily transferred to the skin during use, harmless materials should be used in the surface treatment of the gloves.
4.2 Dimensions
When measured at the location shown in Figure 1, the length (L) of the glove and the width of the palm (W) should conform to the specifications in Table 1, and the inspection level and acceptance should be in accordance with these specifications.
The acceptable quality limit (AQL) is specified in Table 3.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 10 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 528-2009Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties
- GB/T 3512-2014Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests in hot air
- GB/T 2828.1-2012Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
ISO 37 · ISO 188 · ISO 2859
How to Download GB/T 46059-2025
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2828.1-2012 — Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 3512-2014 — Rubber, vulcanized or thermoplastic -- Accelerated ageing and heat resistance tests -- Air-oven method
GB/T 528-2009 — Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties
Secure payment via Stripe
Payments accepted
GB/T 46059-2025
$195.00