Valid

GB/T 43010-2023Closed-circuit dry-cleaning machines - Defining and checking of machine characteristics (English PDF)

封闭式干洗机 定义和机器特性的检验

Preview PDF

This is a limited preview

Buy now to download the full PDF (20 pages)

Need quotation for your management?

Get a formal quotation for GB/T 43010-2023 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

September 7, 2023

Implementation date

April 1, 2024

Scope

GB/T 43010-2023 is the English-translated version of 封闭式干洗机 定义和机器特性的检验.

GB/T 43010-2023 — This document describes test methods applicable to enclosed dry cleaning machines and their following characteristics. ---Solvent consumption; ---Solvent recovery efficiency during drying process; ---Solvent concentration in the atmosphere around a closed dry cleaning machine. For safety requirements for enclosed dry cleaning machines, see GB 25116-2010.

Found what you need?

Document preview — GB/T 43010-2023

National Standard of the People's Republic of China

ICS
97.060
Classification
Y 99

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • 1 Scope
  • 2 Normative reference documents
  • 3 Terms and definitions
  • 4 General test conditions
  • 4.1 Standard test procedures

Foreword

This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1.Structure and Drafting Rules of Standardization Documents"

Drafting.

This document is equivalent to ISO 8232.1988 "Definition of closed dry cleaning machines and inspection of machine characteristics".

This document adds a chapter "Normative References".

This document has made the following minimal editorial changes.

---Amend ISO 8230.1997 to GB 25116-2010 in scope and references;

---The chapter number 7.1 "Applicable Conditions" has been added, and the other chapter numbers in this chapter have been postponed.

Please note that some content in this document may be subject to patents. The publisher of this document assumes no responsibility for identifying patents.

1 Scope

This document describes test methods applicable to enclosed dry cleaning machines and their following characteristics.

---Solvent consumption;

---Solvent recovery efficiency during drying process;

---Solvent concentration in the atmosphere around a closed dry cleaning machine.

For safety requirements for enclosed dry cleaning machines, see GB 25116-2010.

2 Normative reference documents

This document has no normative references.

3 Terms and definitions

The following terms and definitions apply to this document.

3.1

closed-circuitdry-cleaningmachine

Dry cleaning machines with solvent recovery systems in all stages of cleaning, including washing, drying and deodorizing clothes, can avoid.

---Any leakage between the factory and the surroundings of the machine (including inside the machine and pipes);

---Waste discharge (except water, excluding undissolved solvent in the separator siphon).

Note. This definition does not take into account solvent purification operations.

3.2

The amount of solvent consumed by a dry cleaning machine to clean the rated capacity of clothing when the dry cleaning machine cycles according to the standard test program.

Note 1.The unit is liter (L).

Note 2.It can also be expressed as a percentage of nominal capacity.

4 General test conditions

4.1 Standard test procedures

One or both of the following procedures should be used.

---When using standard test program cycles to significantly change machine performance, the program specifically required by the "manufacturer" should be used;

---The standard test procedure is shown in Table 1.The drying inlet temperature is 78 degrees C+/-2 degrees C and the outlet temperature is 58 degrees C+/-2 degrees C.

NOTE 1.For a given machine, the selected cycles are the same for the entire test series.

Note 2.If the machine uses solvents other than PCE, only use the "Manufacturer" cycle.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.

How to Download GB/T 43010-2023

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
20 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 43010-2023

$210.00