Valid

GB/T 42601.3-2023Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (English PDF)

石油、石油化工和天然气工业润滑、轴密封和控制油系统及辅助设备第3部分：一般用途的油系统

Preview PDF

This is a limited preview

Buy now to download the full PDF (39 pages)

Need quotation for your management?

Get a formal quotation for GB/T 42601.3-2023 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 23, 2023

Implementation date

December 1, 2023

Scope

GB/T 42601.3-2023 is the English-translated version of 石油、石油化工和天然气工业润滑、轴密封和控制油系统及辅助设备第3部分：一般用途的油系统.

GB/T 42601.3-2023 is Part 3 of the Chinese series on lubrication, shaft sealing and control oil systems for the petroleum, petrochemical and gas industries, and covers general purpose oil systems.

General purpose means the machinery that is not the critical unspared train: the pumps, fans and smaller drives that a plant has dozens of, where the redundancy demanded of a special purpose system cannot be justified but the equipment still has to run unattended for years.

The standard sets the basic design and the general requirements, then the components - the baseplate, the reservoir, the pumps and their drivers, the coolers, the filters, the transfer valve and the shutdown lube oil tank - the piping covering oil and instrument piping, and the instrumentation, inspection, testing and preparation for shipment. It took effect on 1 December 2023.

Found what you need?

Document preview — GB/T 42601.3-2023

National Standard of the People's Republic of China

ICS: 75.180.20
Classification: J72

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

1 Scope
2 Normative references
3 Terms, abbreviated terms and definitions
4 General

Foreword

This document, in conjunction with ISO 10438-1, specifies requirements for oil systems for general-purpose applications. These oil systems can provide lubrication oil, but not seal oil and can serve equipment such as compressors, gears, pumps and drivers.

Note: The term "general-purpose" is defined in ISO 10438-1.

1 Scope

Note: The term "general-purpose" is defined in ISO 10438-1.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 42601.1-2023 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007, IDT)

ISO 10438-1 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1 : General requirements

ISO 10438-2 : 2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2 : Special-purpose oil systems

ISO 13706 : 2011 Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers

ISO 13709 Centrifugal pumps for petroleum, petrochemical and natural gas industries Note: GB/T 3215-2019 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709 : 2009, MOD)

ISO 15649 Petroleum and natural gas industries - Piping

ISO 16889 Hydraulic fluid power - Filters - Multi-pass method for evaluating filtration performance of a filterelement Note: GB/T18853-2015 Hydraulic fluid power filters - Multi-pass method for evaluating filtration performance of a filter element (ISO16889:2008, MOD)

IEC 60034(all parts) Rotating electrical machines API RP 686 Machinery Installation and Installation Design TEMA Standards of the Tubular Exchanger Manufacturers Association NEMA MG1 Motors and Generators

2 Normative references

GB/T 42601.1-2023 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007, IDT)

ISO 10438-1 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1 : General requirements

ISO 10438-2 : 2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2 : Special-purpose oil systems

ISO 13706 : 2011 Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers

ISO 15649 Petroleum and natural gas industries - Piping

3 Terms, abbreviated terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 42601.1-2023 apply.

3 Terms, abbreviated terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 42601.1-2023 apply.

4.1 Basic design

4.1.1 This document covers general-purpose oil systems. Typical datasheets for general-purpose oil systems are in Annex A. Typical piping and instrument diagrams for general-purpose oil systems are in Annex B. Typical inspector checklists for general-purpose oil systems are in Annex C. General-purpose (GP) oil systems are divided into classes and are defined by a coding system that defines the major components supplied (see Table 1). The user shall choose the applicable class and code based upon the required minimum reliability targets for the equipment train. Various API standards have supplied minimum recommended systems as indicated in Table 2 for their equipment. Annex D is supplied as a reference to provide guidance on the selection of a system.

color: rgb(153, 153, 153);

background-color: rgb(248, 248, 248);

border-bottom: 1px solid rgb(153, 153, 153);

GB/T 42601.3-2023 Petroleum, petrochemical and natural gas industries—Lubrication, shaft-sealing and control-oil systems and auxiliaries—Part 3: General-purpose oil systems (English) Standard No.

Translation Price(USD) 600.0 Implemented on 2023-12-1 Delivery

via email in 1~3 business day

Add GB/T 42601.3-2023 to Cart

Detail of GB/T 42601.3-2023 Standard No.

Petroleum, petrochemical and natural gas industries—Lubrication, shaft-sealing and control-oil systems and auxiliaries—Part 3: General-purpose oil systems Chinese Name

Chinese Classification J72

Professional Classification GB ICS Classification Issued by SAMR; SAC Issued on 2023-05-23 Implemented on 2023-12-1 Status valid Superseded by Superseded on Abolished on Superseding Language English File Format PDF Word Count 20000 words

Translation Price(USD) 600.0 Keywords

GB/T 42601.3-2023, GB 42601.3-2023, GBT 42601.3-2023, GB/T42601.3-2023, GB/T 42601.3, GB/T42601.3, GB42601.3-2023, GB 42601.3, GB42601.3, GBT42601.3-2023, GBT 42601.3, GBT42601.3

Introduction of GB/T 42601.3-2023

Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries- Part 3 : General-purpose oil systems

4.1 Basic design

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 39 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 42601 · ISO 10438 · ISO 13706 · ISO 13709 · ISO 16889

Similar standards

GB 38031-2025|GB/T42601.3-2023|GB/T 1|GB/T 42601|GB/T 3215-2019|GB/T 18853-2015|GB/T 13277.1|GB/T 4976

How to Download GB/T 42601.3-2023

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.