GB/T 42399.3-2023Non-destructive testing instruments - Characterization and verification of ultrasonic phased array equipment - Part 3: Combined system (English PDF)

foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules for Standardization Documents"

drafting.

This document is part 3 of GB/T 42399 "Performance and Inspection of Phased Array Ultrasonic Equipment for Nondestructive Testing Instruments". GB/T 42399

The following parts have been released.

--- Part 1.Instruments;

--- Part 2.Probes;

--- Part 3.Combined system.

This document is equivalent to ISO 18563-3.2015 "Performance and inspection of phased array ultrasonic equipment for non-destructive testing - Part 3.Combination

system".

This document has made the following minimal editorial changes.

--- In order to be consistent with the existing standard series, the name of the standard is changed to "Performance and Inspection of Phased Array Ultrasonic Equipment for Nondestructive Testing Instruments No.

Part 3.Composite Systems".

Please note that some contents of this document may refer to patents. The issuing agency of this document assumes no responsibility for identifying patents.

Introduction

Like the A-type conventional detector, the phased array ultrasonic is based on the pulse reflection method for detection, and the same flaw quantitative and qualitative methods are used.

bit method. However, the phased array ultrasonic detector is a high-performance digital instrument, which can record the signal of the whole detection process.

The system can generate and display high-quality images projected in different directions, so its unique measurement calibration and verification methods need to be specified.

Certainly. GB/T 42399 aims to pass the testing methods and acceptance criteria for phased array ultrasonic detectors including instruments, probes and combined systems

Standards are stipulated, so as to unify the technical requirements of products, so that they can be better applied in actual production and testing.

GB/T 42399 "Performance and Inspection of Phased Array Ultrasonic Equipment for Nondestructive Testing Instruments" is divided into the following three parts.

--- Part 1.Instruments. The purpose is to specify the detection frequency of multi-channel phased array ultrasound in the range of 0.5MHz~10MHz

The detection method and acceptance criteria of the main technical performance of the detector.

--- Part 2.Probes. The purpose is to specify the use of contact method or liquid immersion method, the center frequency range is 0.5MHz~10MHz

The detection methods and acceptance criteria for the main technical performance of phased array probes that need to be inspected after fabrication is completed.

--- Part 3.Combined system. The purpose is to specify the use of linear phased array probes, contact (with or without wedge) or water immersion, center

The performance detection method of phased array combination equipment (that is, connected instruments, probes and cables) with a frequency in the range of 0.5MHz~10MHz

laws and acceptance criteria.

The three parts of GB/T 42399 "Performance and Inspection of Phased Array Ultrasonic Equipment for Nondestructive Testing Instruments" are independent of each other, but they echo each other and form a

into a complete set of standards.

Non-destructive testing instrument phased array ultrasonic equipment

Performance and inspection part 3. combined systems

1 Scope

This document describes the inspection methods and acceptance criteria for the inspection of combined equipment (ie instruments, probes and connecting cables).

This document is applicable to contact type (with or without wedges) or liquid immersion linear array phased array probes with a center frequency of 0.5MHz~10MHz.

Ultrasonic testing system. This detection method is applicable to users in the field or workshop environment. Its purpose is to verify that the system is working correctly,

Beam characteristics or check for system performance degradation. This test method is not intended to prove the suitability of the system for a particular application, but to

Demonstrate the ability of the combined device to generate an ultrasonic sound beam according to the setup.

The scope of this document does not include application-specific device calibration, which is generally covered by the testing process.

This document does not contain the following.

--- Ring array;

---Aperture sequences with different numbers of array elements;

--- The settings of transmission and reception are different (such as excitation aperture, effective number of array elements, delay);

---Adopt a single-array unit signal post-processing technology that is more complex than the simple delay rule (for example. full matrix acquisition).

2 Normative references

The content in the following documents constitutes the essential provisions of this document through normative references in the text. Among them, dated references

For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to

this document.

ISO 5577 Non-destructive testing ultrasonic testing terminology (Non-destructivetesting-Ultrasonictesting-Vocabula-

ry)

Note. GB/T 12604.1 Nondestructive Testing Terminology Ultrasonic Testing (ISO 5577.2017, MOD)

ISO 18563-1 Performance and inspection of phased array ultrasonic equipment for non-destructive testing - Part 1.Instruments (Non-destructivetes-

Note. GB/T 42399.1-2023 Nondestructive Testing Instruments Performance and Inspection of Phased Array Ultrasonic Equipment Part 1.Instruments (ISO 18563-1.

2015, IDT)

EN 1330-4 Terminology for nondestructive testing - Part 4.Terminology for ultrasonic testing (Non-destructivetesting-Terminolo-

EN16018 Non-destructive testing terminology for phased array ultrasonic testing (Non-destructivetesting-Terminology-

EN 16392-2 Performance and inspection of phased array ultrasonic equipment for non-destructive testing Part 2.Probes (Non-destructivetes-

3 Terms and Definitions

The terms and definitions defined in ISO 5577, EN 1330-4, EN 16018 and the following apply to this document.