GB/T 41880-2022Plastics - Epoxy resins - Determination of electrical conductivity of aqueous resin extracts (English PDF)
Also coversGBT41880-2022
Open the GB/T 41880-2022 preview as PDF
This is a limited preview
Buy now to download the full PDF
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 12, 2022
Implementation date
October 12, 2022
Scope
GB/T 41880-2022 (Plastics - Epoxy resins - Determination of electrical conductivity of aqueous resin extracts) is available as an English-translated PDF.
GB/T 41880-2022 — This document describes a method for determining the electrical conductivity of the aqueous extract obtained by extracting epoxy resins with water at 95 °C. This document is only applicable to epoxy resins that are in a molten state at extraction temperature (95 °C). This method is of great significance to epoxy resin used as insulating material for electronic equipment. The electrical conductivity of the extract is used to evaluate the concentration of ionic substances in the resin.
Document preview — GB/T 41880-2022
National Standard of the People's Republic of China
Issued by: SAMR; SAC
Contents
- Foreword...3
- Introduction...4
- 1 Scope...5
- 2 Normative references...5
- 3 Terms and definitions...5
- 4 Reagents...5
- 5 Apparatus...5
- 6 Test procedure...6
- 7 Expression of results...6
- 8 Precision...7
- 9 Test report...7
- Bibliography...8
Foreword
This document is drafted in accordance with GB/T 1.1-2020 "Directives for
standardization - Part 1: Rules for the structure and drafting of standardizing
documents".
This document is identical to ISO 21318:2007 "Plastics - Epoxy resins - Determination
of electrical conductivity of aqueous resin extracts".
This document adds two Clauses "Normative references" and "Terms and definitions".
Attention is drawn to the possibility that some of the elements of this document may be
the subject of patent rights. The issuing authority of this document shall not be held
responsible for identifying any or all such patent rights.
This document was proposed by China Petroleum and Chemical Industry Federation.
This document shall be under the jurisdiction of National Technical Committee 15 on
Plastic of Standardization Administration of China (SAC/TC 15).
Drafting organizations of this document: Shandong Shengquan New Materials Co., Ltd.,
Dalian Qihua New Material Co., Ltd., Guangzhou Huaxin Testing Technology Co., Ltd.,
Shanghai Qianshi Technology Co., Ltd., Nantong Xingchen Synthetic Materials Co.,
Ltd., Jiangsu Yangnong Kumho Chemical Co., Ltd., Dongguan National New Materials
Institute Co., Ltd., Jilin Province Product Quality Supervision and Inspection Institute.
Main drafters of this document: Liu Mingxiang, Guo Shuzhi, Wang Jing, Zhang Xiumei,
Lu Ning, Gao Hui, Li Fu, Huang Yong, Xu Xiaohu, Chen Yuwen, Wang Dabing, Wang
Meiling, Li Shangyu, Guo Yingying.
Plastics - Epoxy resins - Determination of electrical
conductivity of aqueous resin extracts
Warning: Personnel using this document should be familiar with normal
laboratory operations. This document does not purport to address all safety issues
during use. Users shall develop safety and health measures and ensure compliance
with regulatory requirements.
1 Scope
This document describes a method for determining the electrical conductivity of the
aqueous extract obtained by extracting epoxy resins with water at 95 °C.
This document is only applicable to epoxy resins that are in a molten state at extraction
temperature (95 °C).
This method is of great significance to epoxy resin used as insulating material for
electronic equipment. The electrical conductivity of the extract is used to evaluate the
concentration of ionic substances in the resin.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
There are no terms and definitions to be defined in this document.
4 Reagents
Water: Use distilled water and/or deionized water with an electrical conductivity lower
than 2.0 µS/cm.
5 Apparatus
5.1 Electrical conductivity meter: Accurate to 0.1 µS/cm. It can be immersed in the
aqueous extract and has temperature compensation function.
5.2 Glass measuring cylinder: 100 mL.
5.3 Analytical balance: Accurate to 0.01 g.
5.4 Electrothermal blowing drying oven: It is capable of maintaining a temperature of
95 °C+/-3 °C.
5.5 High-density polyethylene bottle: 100 mL (with a screw cap).
5.6 Polyethylene cup: 100 mL.
6 Test procedure
6.1 Weigh 8.00 g+/-0.05 g of test portion into a 100 mL high-density polyethylene bottle
(5.5).
6.2 Add 80 mL+/-2 mL of water into the bottle and cover it.
6.3 Put the bottle into the electrothermal blowing drying oven (5.4) which has been
stabilized at 95 °C.
6.4 After 30 min, slowly open the bottle cap to release the internal pressure, to prevent
the bottle from bursting. Then retighten the cap.
Warning: When performing test procedure 6.4, wear protective gloves and mask.
6.5 After 20 h+/-0.5 h, take the bottle out of the electrothermal blowing drying oven; cool
it to room temperature.
6.6 Pour water into a polyethylene cup (5.6); use an electrical conductivity meter (5.1)
to measure the electrical conductivity at 25 °C.
6.7 Without adding test portion, according to the same steps, use the same water to carry
out the blank test.
7 Expression of results
Calculate the electrical conductivity gamma of the aqueous extract according to formula (1),
expressed in microsiemens per centimeter (µS/cm):
Where:
gammaS - Indicated value of electrical conductivity of aqueous extract of test portion, in
microsiemens per centimeter (µS/cm);
gammaB - Indicated value of electrical conductivity of blank test, in microsiemens per
......
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.
How to Buy GB/T 41880-2022
- 1Add to cart. Click the "Buy GB/T 41880-2022" button on this page. You can add more standards before checkout.
- 2Checkout. Enter your email and billing details. Payment is processed securely by Stripe (cards, Apple Pay, Google Pay supported).
- 3Instant delivery (0–9 sec). Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4Invoice included. A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 46830.2-2026 — Plastics - Liquid crystal polymer (LCP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
GB/T 28593-2026 — Sand and dust weather warning levels
GB/T 19608.3-2026 — Classification of special environmental conditions - Part 3: Plateau
Secure payment via Stripe
Payments accepted
GB/T 41880-2022
$95.00