Valid

GB/T 41425-2022Test method for overall impact resistance of baby walking harness (English PDF)

婴幼儿学步带整体承载冲击性能试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (24 pages)

Need quotation for your management?

Get a formal quotation for GB/T 41425-2022 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

April 15, 2022

Implementation date

November 1, 2022

Scope

GB/T 41425-2022 is the English-translated version of 婴幼儿学步带整体承载冲击性能试验方法.

GB/T 41425-2022 is the Chinese national method for testing the overall impact resistance of a baby walking harness, the strap that holds a toddler learning to walk.

It describes the principle of the test, the device that applies the impact and the procedure that is followed, together with the way the result is judged and reported.

It applies to walking harnesses whose main material is a textile fabric. Makers of baby articles, retailers and the laboratories that check children's products use it. Issued on 15 April 2022, it has applied since 1 November 2022.

Found what you need?

Document preview — GB/T 41425-2022

National Standard of the People's Republic of China

ICS
61.020
Classification
Y 75

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • Introduction4
  • 1 Scope5
  • 2 Normative References5
  • 3 Terms and Definitions5
  • 4 Principle6
  • 5 Apparatus6
  • 6 Samples7
  • 7 Test Procedures7
  • 8 Test Data Processing8
  • 9 Test Report8
  • Appendix A (Informative) Walking Harness Type10
  • Appendix B (Informative) Gripper Type12

1 Scope

This Document describes the principles, devices and methods of testing the overall impact resistance of baby walking harness.

This Document applies to walking harness products made of textile fabrics as the main material.

2 Normative References

This Document does not have the normative references.

3 Terms and Definitions

For the purposes of this Document, the following terms and definitions apply.

3.1 Baby walking harness

Pad and strap device for supporting and protecting baby from sitting to walking independently.

3.2 Overall impact resistance

The bearing capacity of the walking harness under a certain speed and amplitude of movement and shock when a quantitative load is applied.

3.3 Baby walking harness with top handle

The gripping part is mainly made of hard material as a top handle of baby walking harness.

NOTE: See Figure A.1 in Appendix A for the schematic diagram.

3.4 Baby walking harness with strap

The gripping part is mainly a circular baby walking harness sewn with textile fabrics.

NOTE 1: Types can be divided into single-leash baby walking harness and double-leash baby walking harness.

NOTE 2: The schematic diagram is shown in Figure A.2.

4 Principle

Install the walking harness on the load model; lift it by pulling the belt of the walking harness; and make the walking harness impact by reciprocating with a certain speed and frequency within a certain stroke, so as to evaluate the overall impact resistance of the walking harness.

5 Apparatus

5.1 Impact testing machine Baby walking harness

impact testing machine shall include the following components:

a) Metal bracket: a metal bracket with a height of no less than 200cm, fixed on the ground;

b) Impact device: The impact device includes impact rods and common clamps (C-type gripper, cylindrical gripper, telescopic gripper), which can move up and down, with a one-way stroke of (100±2) mm; reciprocating motion of frequency of (120±5) times/min; adding the load model of 15kg on the impact device is set as the benchmark; and the maximum load can be 20kg after placing the counterweight;

c) Control device: It can adjust the oscillation impact rate; can set and record the number of impact tests; and has the function of automatic shutdown when it is dropped in the middle of the test.

5.2 Fixtures

5.2.1 C-type gripper

The gripper that is used when testing a single-leash walking harness, see Figure B.1 in Appendix B for the schematic diagram of the gripper. The inner side of the C-type gripper shall be lined with a soft rubber film to avoid abrasion of the specimen; and the thickness of the soft rubber film is 1mm.

5.2.2 Cylindrical gripper

The gripper that is used when testing the double-leash walking harness, the schematic diagram of the gripper is shown in Figure B.2.

5.2.3 Telescopic Gripper

The gripper that is used when testing the walking harness with top handle, the schematic diagram of the gripper is shown in Figure B.3.

--- When testing the double-leash walking harness, adjust the two leashes to the maximum length and fix them on the cylindrical gripper.

7 Test Procedures

7.4 Set the frequency of the reciprocating motion of the impact testing machine to (120±5) times/min.

7.5 Set the number of reciprocating impacts of the impact testing machine to 2500 times; take 2500 times of impact as the inspection cycle; and the total number of tests is 20000 times.

7.6 After the test, check the status of the walking harness; and its connectors, buckles, seams, straps, fabrics and other structures shall not be damaged such as tearing, disconnection, detachment, and damage to the fabric at the stressed part, which may affect the safety of the baby.

7.7 In the course of the test, any damage to the walking harness product specified in 7.6, which causes the walking harness to fall, and the instrument automatically stops. The test shall be terminated, and the number of impacts at this time shall be recorded.

8 Test Data Processing

The results are expressed in the number of impacts:

--- The number of impacts shall be recorded according to the number of times at the end of the test;

--- If there is any damage to the walking harness product specified in 7.6 during the test, the damage shall be recorded;

--- If the walking harness does not have any damage specified in 7.6 until 20000 times of impacts, record the number of impacts as " >20,000";

--- The test unit is (times), and the result is reserved as an integer.

9 Test Report

The test report shall include the following:

a) this Document number;

b) Sample name, serial number, type, manufacturer (or trademark), production date;

c) instrument model and test conditions;

d) number of specimens;

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 24 pages — is available in the English PDF.

Similar standards

How to Download GB/T 41425-2022

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
24 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 41425-2022

$150.00