Valid

GB/T 41378-2022Plastics - Blow-moulded polypropylene containers for packaging of liquid food stuffs (English PDF)

塑料 液态食品包装用吹塑聚丙烯容器

Preview PDF

This is a limited preview

Buy now to download the full PDF (34 pages)

Need quotation for your management?

Get a formal quotation for GB/T 41378-2022 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

March 9, 2022

Implementation date

October 1, 2022

Scope

GB/T 41378-2022 is the English-translated version of 塑料 液态食品包装用吹塑聚丙烯容器.

GB/T 41378-2022 is the Chinese standard "Plastics - Blow-moulded polypropylene containers for packaging of liquid food stuffs". Its scope clause reads: This document specifies the requirements for blow-molded polypropylene round-bottom containers with a capacity of not more than 2L (including 2L) for liquid food packaging.

Book The document also specifies quality tolerances, dimensional tolerances, sampling methods, test requirements and performance requirements for blow-molded polypropylene containers for liquid food packaging.

NOTE. It is not intended that polypropylene is the only polymer suitable for this application, as include high density polyethylene (PE-HD), polyethylene terephthalate (PET) Other polymers, etc., are also suitable. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 41378-2022

National Standard of the People's Republic of China

Classification
Y 28

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions

1 Scope

This document specifies the requirements for blow-molded polypropylene round-bottom containers with a capacity of not more than 2L (including 2L) for liquid food packaging. Book

The document also specifies quality tolerances, dimensional tolerances, sampling methods, test requirements and performance requirements for blow-molded polypropylene containers for liquid food packaging.

NOTE. It is not intended that polypropylene is the only polymer suitable for this application, as include high density polyethylene (PE-HD), polyethylene terephthalate (PET)

Other polymers, etc., are also suitable.

2 Normative references

The contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, dated citations documents, only the version corresponding to that date applies to this document; for undated references, the latest edition (including all amendments) applies to this document.

ISO 472 Plastics Terms and Definitions (Plastics- Vocabulary)

ISO 1873-1 Plastics Polypropylene (PP) molding and extrusion materials - Part 1.Nomenclature system and classification basis 1) (Plastics- specifications)

ISO 1873-2 Plastics Polypropylene (PP) molding and extrusion materials - Part 2.Specimen preparation and determination of properties 2) (Plastics-

ISO 2859-1 Count sampling inspection procedures - Part 1.Lot-by-lot inspection sampling plans retrieved by acceptance quality limit (AQL)

1) ISO 1873-1 was obsolete in.2015 and was replaced by ISO 19069-1 in the same year.

2) ISO 1873-2 was obsolete in.2016 and was replaced by ISO 19069-2 in the same year.

3 Terms and Definitions

The following terms and definitions apply to this document.

NOTE. For terms and definitions in this document, please refer to ISO 472.Containers produced using ISBM technology have a neck height (H) from the highest point of the container neck to

The vertical distance of the bottom surface of the support ledge. The full capacity can also be determined by the method specified in Appendix B by using a specific volume test equipment. For bottles and loose

For mouth containers, the nominal capacity is about 90% of the full capacity.

3.1 extrusion blow-moulded container

A container formed by blowing the extruded parison of thermally softened thermoplastic against the inner wall of the mold by applying air pressure.

GB/T 43198 | GB/T 41001 | GB/T 41003.1 | GB/T 47711 | GB/T 18006.1 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 34 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 472 · ISO 1873 · ISO 2859 · ISO 19069

How to Download GB/T 41378-2022

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
34 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 41378-2022

$330.00