Valid

GB/T 40722.2-2021Styrene-butadiene rubber(SBR) - Determination of the microstructure of solution-polymerized SBR - Part 2: FTIR with ATR method (English PDF)

苯乙烯-丁二烯橡胶(SBR) 溶液聚合SBR微观结构的测定 第2部分:红外光谱ATR 法

Preview PDF

This is a limited preview

Buy now to download the full PDF (30 pages)

Need quotation for your management?

Get a formal quotation for GB/T 40722.2-2021 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

October 11, 2021

Implementation date

May 1, 2022

Scope

GB/T 40722.2-2021 is the English-translated version of 苯乙烯-丁二烯橡胶(SBR) 溶液聚合SBR微观结构的测定 第2部分:红外光谱ATR 法.

GB/T 40722.2-2021 — This document describes the use of Fourier Transform Infrared Spectroscopy (FTIR) Attenuated Total Reflectance (ATR) for the determination of solution polymerized styrene-butadiene The steps of the butadiene microstructure and styrene content in rubber (S-SBR).

The styrene content is relative to the mass fraction of the entire polymer. The content of 1,4-trans structure, 1,4-cis structure, and 1,2-vinyl structure is the mole fraction (%) relative to the butadiene portion.

This document applies to S-SBR raw rubber. Note 1.For S-SBR containing polystyrene or styrene content greater than 45%, the precision shown in Appendix A may not be obtained.

Note 2.This document uses "vinyl", "trans" and "cis". Usually vinyl, trans and cis are expressed as follows. --- Vinyl. vinyl unit, vinyl bond, 1,2-unit, 1,2-bond, 1,2-vinyl unit or 1,2-vinyl bond; ---Trans.

1,4-trans unit, 1,4-trans bond, trans-1,4-unit or trans 1,4-bond; --- cis. 1,4-cis unit, 1,4-cis bond, cis-1,4-unit or cis-1,4 bond.

Found what you need?

Document preview — GB/T 40722.2-2021

National Standard of the People's Republic of China

Classification
G 35

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • 1 Scope1
  • 2 Normative references1
  • 3 Terms and definitions1
  • 4 Principle1
  • 5 Instrument1
  • 5.1 Infrared spectrometer1
  • 5.2 ATR Annex2
  • 6 Calibration2
  • 6.1 Infrared spectrometer2
  • 6.2 ATR Annex2
  • 7 Sampling2

Foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules of Standardization Documents"

Drafting.

This document is the second part of GB/T 40722 "Measurement of SBR Microstructure by Solution Polymerization of Styrene-Butadiene Rubber (SBR)".

GB/T 40722 has released the following parts.

---Part 2.Infrared spectroscopy ATR method.

The translation method used in this document is equivalent to the ISO 21561-2.2016 "SBR solution polymerization of styrene-butadiene rubber (SBR).

Determination of structure Part 2.Infrared spectroscopy ATR method.

A chapter "Terms and Definitions" has been added to this document.

The Chinese documents that have consistent correspondence with the normatively cited international documents in this document are as follows.

---GB/T 15340-2008 Natural and synthetic raw rubber sampling and sample preparation methods (ISO 1795.2000, IDT).

Introduction

The microstructure content directly affects the processing and application performance of solution polymerized styrene-butadiene rubber (S-SBR), which is important for guiding the new production of S-SBR.

Product development and product quality control are of great significance.

With the development of analytical detection technology, 1H-NMR method, infrared spectrum coating method, infrared spectrum ATR method and other detection methods are used for

Determination of polymer microstructure.

GB/T 40722 provides a technical basis for measuring the microstructure of solution polymerized styrene-butadiene rubber.

GB/T 40722 is intended to be composed of two parts.

---Part 1.1H-NMR method and infrared spectroscopy coating method. The purpose is to satisfy the use of hydrogen nuclear magnetic resonance spectroscopy and infrared spectroscopy.

Membrane method user's measurement needs.

---Part 2.Infrared spectroscopy ATR method. The purpose is to meet the measurement needs of users using infrared spectroscopy ATR method.

Styrene-butadiene rubber (SBR)

Determination of the Microstructure of SBR by Solution Polymerization

Part 2.Infrared Spectroscopy ATR Method

Warning---The personnel using this document should have practical experience in formal laboratory work. This document does not indicate all possible safety issues

It is the responsibility of users to take appropriate safety and health measures and to ensure compliance with the conditions stipulated by relevant national laws and regulations.

Note---Some procedures in this document may involve the use or generation of substances that are harmful to the local environment, or may generate waste,

After use, it should be safely handled and disposed of in accordance with the corresponding documents.

1 Scope

This document describes the use of Fourier Transform Infrared Spectroscopy (FTIR) Attenuated Total Reflectance (ATR) for the determination of solution polymerized styrene-butadiene

The steps of the butadiene microstructure and styrene content in rubber (S-SBR). The styrene content is relative to the mass fraction of the entire polymer.

The content of 1,4-trans structure, 1,4-cis structure, and 1,2-vinyl structure is the mole fraction (%) relative to the butadiene portion.

This document applies to S-SBR raw rubber.

Note 1.For S-SBR containing polystyrene or styrene content greater than 45%, the precision shown in Appendix A may not be obtained.

Note 2.This document uses "vinyl", "trans" and "cis". Usually vinyl, trans and cis are expressed as follows.

--- Vinyl. vinyl unit, vinyl bond, 1,2-unit, 1,2-bond, 1,2-vinyl unit or 1,2-vinyl bond;

---Trans. 1,4-trans unit, 1,4-trans bond, trans-1,4-unit or trans 1,4-bond;

--- cis. 1,4-cis unit, 1,4-cis bond, cis-1,4-unit or cis-1,4 bond.

2 Normative references

The contents of the following documents constitute the indispensable clauses of this document through normative references in the text. Among them, dated quotations

Only the version corresponding to that date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to

This document.

ISO 1795 Natural raw rubber and synthetic raw rubber sampling and sample preparation method (Rubber, rawnaturalandrawsynthetic-

Samplingandfurtherpreparativeprocedures)

3 Terms and definitions

There are no terms and definitions that need to be defined in this document.

4 Principle

The infrared spectrum of S-SBR was obtained by infrared spectroscopy ATR method. According to the corresponding microstructure of butadiene unit and styrene

The absorbance at a specific wavelength, using the formula specified in this document, calculate the content of each component.

5 Instruments

5.1 Infrared spectrometer

The infrared spectrum should meet the following conditions.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 30 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 1795

How to Download GB/T 40722.2-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
30 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 40722.2-2021

$240.00