Valid

GB/T 40430-2021Road vehicles—Diagnostic communication over controller area network (DoCAN) —Dictionary (English PDF)

道路车辆 基于控制器局域网的诊断通信 符号集

Preview PDF

This is a limited preview

Buy now to download the full PDF (36 pages)

Need quotation for your management?

Get a formal quotation for GB/T 40430-2021 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

August 20, 2021

Implementation date

March 1, 2022

Scope

GB/T 40430-2021 is the English-translated version of 道路车辆 基于控制器局域网的诊断通信 符号集.

GB/T 40430-2021 is the dictionary of diagnostic trouble codes (DTC) for diagnostic communication over the controller area network (DoCAN) of road vehicles. It sets general requirements, the format structure of the codes and the descriptions of diagnostic trouble codes.

Each code combines a letter indicator - B for body, C for chassis, P for powertrain and U for network and vehicle integration - with a hexadecimal number, and ranges controlled by ISO/SAE are kept apart from those controlled by manufacturers or reserved.

It covers the standard code set and the fault type descriptions contained in SAE J2012-DA and the decoding of enhanced diagnostic DTCs, with informative guidelines for naming codes and recommended fault type bytes.

Vehicle manufacturers and suppliers use it when assigning codes. It was issued on 20 August 2021 and has applied since 1 March 2022.

Found what you need?

Document preview — GB/T 40430-2021

National Standard of the People's Republic of China

ICS
43.040
Classification
T 36

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • Introduction4
  • 1 Scope7
  • 2 Normative references7
  • 3 Terms and definitions8
  • 4 General requirements8
  • 5 Format structure9
  • 6 Descriptions of diagnostic trouble code13
  • Appendix A (Informative) Guidelines for naming diagnostic trouble codes17
  • Appendix B (Informative) FTB recommended fault type byte21
  • References36

1 Scope

This document specifies the general requirements, format structure, description of diagnostic trouble codes, for the diagnostic communication symbol set of the vehicle controller area network.

This document is applicable to the diagnostic trouble code (DTC) of the diagnostic communication standard for road vehicle controller area network.

The on-board diagnostic system (OBD) needs to report the code, when a fault is detected.

This document also applies to the decoding of enhanced diagnostic DTC. Meanwhile it reserves bytes for specific purposes of vehicle manufacturers. The format of diagnostic trouble codes in this document includes:

a) The set of standard diagnostic trouble codes AND the description contained in SAE J2012-DA. The two most significant bytes of DTC can be decoded, according to two different lists. The DTC format identifiers 0016 and 0416;

b) The description of the standard set of diagnostic fault code subtypes, which is contained in SAE J2012-DA, is called the fault type (only applicable to the use of three-byte DTC).

2 Normative references

The contents of the following documents constitute the indispensable clauses of this document through normative references in the text. Among them, for dated reference documents, only the version corresponding to that date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document.

ISO 15031-2 Road vehicles - Communication between vehicles and external equipment for emissions-related diagnostics - Part 2: Guidelines on terms, definitions, abbreviations and acronyms

4 General requirements

- Ordinary open-circuit;

- Scope/performance fault;

- Low circuit state;

- High circuit state.

The low circuit state is measured by external circuits, components or connected systems. The signal type (voltage, frequency, etc.) shall be included behind the low circuit state signal.

The high circuit state is measured by external circuits, components or connected systems. The signal type (voltage, frequency, etc.) shall be included behind the high circuit state signal.

5 Format structure

5.1 Description

The diagnostic trouble code consists of an alphanumeric indicator, which is followed by a hexadecimal number. The alphanumeric indicator B0-B3 is used for the vehicle body; C0-C3 is used for the chassis; P0-P3 is used for the powertrain; U0-U3 is used for network/vehicle integration. The correct assignment of alphanumeric indicators depends on the area, which is most suitable for the function. In most cases, diagnostic information needs to be requested from a specific controller. Therefore, the alphanumeric indicator will be implied, BUT this does not mean that all codes supported by a specific controller have the same alphanumeric indicator.

The DTC structure is as shown in Figure 1.

5.3 Manufacturer controlled code (non-uniform DTC)

The area, within each letter indicator, can be used for manufacturer-controlled DTC. Due to differences in basic system, execution process or diagnostic strategy, these fault codes are usually not widely adopted by manufacturers.

When assigning fault codes in the manufacturer's control area, each vehicle manufacturer or supplier shall maintain the consistent design and development, of diagnostic algorithms, software, diagnostic fault codes, on their production lines. Although each manufacturer can define a controlled DTC, to meet its specific controller algorithm, all DTC descriptions shall comply with SAE J1930 or ISO 15031-2.

5.4 Body system

The DTC number and description are in SAE J2012-DA:

- B0XXX ISO/SAE controlled;

- B1XXX manufacturer controlled;

- B2XXX manufacturer controlled;

- B3XXX files reserved.

5.5 Chassis system

The DTC number and description are in SAE J2012-DA:

- C0XXX ISO/SAE controlled;

- C1XXX manufacturer controlled;

- C2XXX manufacturer controlled;

- C3XXX files reserved.

5.6 Powertrain

The DTC number and description are in SAE J2012-DA:

- P0XXX ISO/SAE controlled;

- P1XXX manufacturer controlled;

6 Descriptions of diagnostic trouble code

The basic DTC description of all body and chassis systems, in SAE J2012-DA, is more general (that is, the failure mode is not embedded), so it is only allocated for the 3-byte DTC structure. Due to the use of the fault type byte as the third (least significant) byte, these DTCs only need to assign a single DTC number and description to each component, not the failure mode.

6.2 Powertrain

The powertrain category covers the functions of the engine, transmission, its powertrain accessories. For the powertrain, a description has been assigned to each designated fault code, to indicate the circuit, component or system area, that has been determined to be faulty. Where possible, different descriptions, which are related to a particular sensor or system, are combined. If there are different fault descriptions for different types of faults, the group will also have a "generic" description, as the code/information of the first group. According to the specific strategy and the complexity of the diagnosis, the manufacturer has the right to choose, when performing the diagnosis.

In the case of circuits, components or systems with more specific fault descriptions, the manufacturer shall select the DTC, that is most suitable for diagnosable faults. The description is intended to be more applicable, so that the manufacturer uses it as frequently as possible, without conflicting with its dedicated maintenance procedures. The terms "low" and "high", which are used in the description, especially the terms related to the input signal, refer to the voltage and frequency at the controller pins. The specific levels of "low" and "high" shall be specified by each manufacturer, to better meet their needs.

For example, when diagnosing a 5 V reference voltage throttle position sensor (TP sensor), if the input signal of the powertrain control module (PCM) is fixed at close to 0 V, the manufacturer can select freely from two codes: P0120 (throttle/pedal position sensor/switch A circuit) or P0122 (accelerator/pedal position sensor/switch a low circuit state), depending on the manufacturer's diagnostic procedures. If the input signal of the powertrain control module (PCM) is stable at a reference voltage of 5 V, the manufacturer can also select freely from two codes: P0120 (throttle/pedal position sensor/switch A circuit) or P0123 (throttle/pedal position sensor/switch A high circuit state), depending on the manufacturer's diagnostic procedures. If the input signal of the powertrain control module is stable at 1.5 V at idling speed, instead of the expected 1.0 V, the manufacturer can select freely from two codes: P0120 (throttle valve/pedal position sensor/switch A circuit) or P0121 (throttle valve/pedal position sensor/switch A circuit range/performance), depending on the manufacturer's diagnostic procedures. The root cause, that causes the throttle position sensor's voltage to be higher than expected, may be the malfunction of throttle position sensor, the corrosion of connection, or the inappropriate correction of throttle position. The root cause is determined through diagnostic procedures.

The relevant description is not defined in DTC, thus allowing manufacturers to flexibly define DTC.

6.3 Body system

The body system category covers the relevant functions inside the passenger compartment, which can provide passengers with help, comfort, convenience, safety. A description has been assigned to each specific fault code, to indicate the component or system area, that is determined to be faulty. Unlike the powertrain, the description of the body system's fault codes is general. The powertrain DTC includes different DTCs (such as low circuit state, high circuit state, principle, etc.), for each failure mode. The body system DTC is designed to support only basic components, in the description, which makes it dependent on the diagnostic protocol, that supports sub-fault failure strategies. The manufacturer shall select the appropriate failure mode (for example: short-circuit to ground, short-circuit to power supply, signal instability, etc.), to apply to general DTC descriptions. The body sub-part, which is supported by this component, is currently the restraint system.

6.4 Chassis system

The chassis system category covers the related functions outside the passenger compartment, which mainly include mechanical systems, such as braking, steering, suspension. A description has been assigned to each specific fault code, to indicate the component or system area, that is determined to be faulty. Unlike the powertrain, the description of the chassis system's fault codes is general. The powertrain DTC includes different DTCs (such as low circuit state, high circuit state, principle, etc.), for each failure mode. The chassis system DTC is designed to support only basic components, in the description, which makes it dependent on the diagnostic protocol, that supports sub-fault failure strategies. The manufacturer shall select the appropriate failure mode (such as short-circuit to ground, short-circuit to power, signal instability, etc.), to apply to general DTC descriptions. The supported chassis sub-parts, which are included in this group, are brakes and traction control.

6.5 Network/vehicle integration system

The network communication/vehicle integration system category covers the functions, which are shared between the computers and/or systems on the vehicle. A description has been assigned to each specific fault code, to indicate the component or system area, that is determined to be faulty. The description of the data link is general, in order to allow manufacturers to use different communication protocols. The description of the control module is universal, to allow manufacturers to reuse DTC for new control modules, along with technological innovations. In addition, additional sub-fault information can be used, to supplement the description, such as the "fault type byte" data, which […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 36 pages — is available in the English PDF.

Referenced standards

Normative references

ISO 15031-2

Similar standards

How to Download GB/T 40430-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
36 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 40430-2021

$360.00