GB/T 40275-2021Textiles—Quantitative analysis of bicomponent fiber—Melting microscopy method (English PDF)
纺织品 双组分复合纤维定量分析方法 熔融显微镜法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 40275-2021 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 21, 2021
Implementation date
December 1, 2021
Scope
GB/T 40275-2021 is the English-translated version of 纺织品 双组分复合纤维定量分析方法 熔融显微镜法.
GB/T 40275-2021 describes a melting microscopy method for finding the mass fraction of each component in a bicomponent fibre, made of two polymers with different chemical or physical structures.
It applies to bicomponent fibres whose components can be told apart by melting and to textile products whose appearance is unchanged; where the chemical dissolution method also works, that method is preferred.
Cross-sectional images are collected under a microscope, the components are identified from their melting points on a heating stage, and their cross-sectional area ratio is measured with digital fibre analysis software or a micro-projector, following FZ/T 01101-2008.
It also covers result calculation, the test report and, in a normative annex, the coefficient of variation, the allowable error rate and the number of additional test fibres. It was issued on 21 May 2021 and has applied since 1 December 2021.
Found what you need?
Document preview — GB/T 40275-2021
National Standard of the People's Republic of China
- ICS
- 59.080.01
- Classification
- W 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative References4
- 3 Terms and Definitions4
- 4 Principle4
- 5 Instruments, Equipment and Materials5
- 6 Test Procedures5
- 7 Calculation and Result Expression7
- 8 Test Report8
- Appendix A (informative) Cross-sectional Morphology of Sheath-core Type, Paralleling Type, Fibril Matrix Type and Split Type of Bicomponent Fibers9
- Appendix B (informative) Volume Density and Melting Point of Conventional Components in Bicomponent Fiber11
- Appendix C (normative) Determination of Coefficient of Variation, Allowable Error Rate and Number of Increased Test Fibers12
- Bibliography15
1 Scope
This Standard describes the method of adopting the melting microscopy method for the determination of the mass fraction of each component in the bicomponent fiber.
This Standard is applicable to bicomponent fiber identifiable by melting and textile products with unchanged appearance.
NOTE: for samples that can be tested by both the chemical dissolution method and this Method, the chemical dissolution method is preferred.
2 Normative References
The content of the following document constitutes indispensable clauses of this document through the normative references in the text. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document.
FZ/T 01101-2008 Textile Test Method - Fiber Content - Quantitative Physical Analysis
3 Terms and Definitions
The following terms and definitions are applicable to this document.
3.1 Bicomponent Fiber
Bicomponent fiber refers to a fiber composed of two high polymers with different chemical or physical structures.
NOTE: bicomponent fibers include four types of structures: sheath-core type, paralleling type, fibril matrix type and split type, etc.
4 Principle
After using a microscope to observe and collect the cross-sectional images of the bicomponent fiber. In accordance with the different characteristics of melting point, morphology, polarity and solubility, determine the corresponding fiber component; collect images at 12 different positions; ensure that the images are not repeatedly collected on the fibers. Among the 12 collected images, there shall be at least 120 fibers with clear cross-sections.
If the bicomponent is relatively approximate in morphology and size, it may cause relatively significant interference to the quantitative determination. Collect 1 clear image, then, at the same position, take the polarized image to assist the quantitative determination.
6 Test Procedures
6.3 Qualitative Analysis of Fiber Components
6.3.1 At a rate of 3 °C/min ~ 4 °C/min, raise the temperature of the fiber specimen on the heating table. When a certain component melts, immediately transfer it to the heat preservation state; record the melting temperature.
6.3.2 Fine-tune the digital metallographic stereo-microscope (5.5); magnify by 500 ~ 1,000 times to observe the melting process of the low-melting component in the fibers.
After most of the component is melted, collect the post-melting image; continue to raise the temperature; determine and record the melting point of the other component.
Combine the melting image, or supplemented by the difference of the polarized image, determine the morphology of the bicomponent fiber (see Appendix A) and the distribution position of each component in the clear image.
6.3.3 In accordance with the melting point of each component, conduct the qualitative analysis; determine the corresponding volume density (see Appendix B).
NOTE: if the determined melting points of the bicomponent are relatively close, then, refer to FZ/T 01057, supplemented by other qualitative methods to conduct the identification.
6.4 Quantitative Determination of Fiber Components
6.4.1 Determination of cross-sectional area ratio of bicomponent
6.4.1.1 Method A: determination by digital fiber analysis software
Respectively import the 60 clear fiber cross-sectional images collected in 6.2 into the digital fiber analysis software matching the digital metallographic stereo-microscope (5.5). In accordance with 7.2.1.2 in FZ/T 01101-2008, determine the number of pixels corresponding to the cross-sectional area of the bicomponent in each fiber; calculate the ratio of the two; the result shall retain two decimal places.
6.4.1.2 Method B: determination by micro-projector
Respectively import the 60 clear fiber cross-sectional images collected in 6.2 into the micro-projector (5.6). In accordance with 7.2.1.1 in FZ/T 01101-2008, determine the cross-sectional area of the bicomponent in each fiber; calculate the ratio of the cross- […]
Appendix C (normative) Determination of Coefficient of Variation, Allowable Error Rate and Number of Increased Test Fibers
C.1 Calculation of Coefficient of Variation
The coefficient of variation shall be calculated in accordance with Formula (C.1) and Formula (C.2). The calculation result shall retain two decimal places; the third decimal place is rounded when it is non-zero.
Where, S---the standard deviation of the mass fraction of a certain component in the fiber, expressed in (%);
X1i---the mass fraction of a certain component of the ith fiber, expressed in (%);
mean X1---the average mass fraction of a certain component in the fiber, expressed in (%); N---the total number of test fibers;
CV---the coefficient of variation of the mass fraction of a certain component in the fiber, expressed in (%).
C.2 Calculation of Allowable Error Rate
A large number of n test values are in approximately normal distribution. Under the confidence level of 95%, the true value will fall within the interval of the arithmetic mean value X ± C of the test result of the specimen. This interval is known as the confidence limit. The half-width value C and the allowable error rate of the confidence interval shall be calculated in accordance with Formula (C.3) ~ Formula (C.5): […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 40275-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
FZ/T 01101-2008 — Textile test method. Fiber content. Quantitative physical analysis
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 40275-2021
$225.00