Valid

GB/T 40116-2021Foil bearings - Performance of hydrodynamic gas journal bearings - Testing of static load capacity, friction coefficient and lifetime (English PDF)

箔片轴承 气体动压径向轴承性能 静态承载能力、摩擦因数和寿命测试

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 40116-2021 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

May 21, 2021

Implementation date

December 1, 2021

Scope

GB/T 40116-2021 is the English-translated version of 箔片轴承 气体动压径向轴承性能 静态承载能力、摩擦因数和寿命测试.

GB/T 40116-2021 is the Chinese national standard on the performance of foil hydrodynamic gas journal bearings, a translation identical with ISO 13939:2019.

It describes the test method and the way results are compared for foil gas journal bearings, which are lubricated by air and carried by the gas pressure that the rotating shaft generates; the tests cover the static load capacity, the friction factor and the service life, so that results obtained under different bearing sizes, shaft speeds, ambient pressures and humidities can be compared.

Clause 3 defines take-off, clearance, bearing torque, load capacity and initial load. The method assumes a steady state, requires the bearing to hold its speed, and leaves out loads that vary in magnitude or direction with time. It was issued on 21 May 2021 and has applied since 1 December 2021.

Found what you need?

Document preview — GB/T 40116-2021

National Standard of the People's Republic of China

ICS
21.100.10
Classification
J 12

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions

Foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1: Structure and Drafting Rules of Standard Documents" Drafting.

This document uses the translation method to be equivalent to ISO 13939:2019 "Foil Bearings Foil Radial Bearing Performance Test Static Load Capacity Force, friction factor and life test". This document has made the following editorial changes.

---Since foil bearings can use other lubricating media or adopt hydrostatic lubrication, in order to be consistent with the content, the name is changed to Static load capacity, friction factor and life test of gas dynamic pressure radial bearing performance of single-piece bearing".

1 Scope

This document describes the performance test method and result comparison method of foil gas dynamic pressure radial bearings. The bearing is lubricated by air (gas).

The sliding medium is supported by the gas dynamic pressure generated by the rotation of the shaft. The test method given in this document aims to test and evaluate the dynamic pressure of foil gas The static load carrying capacity, friction factor and service life of the radial bearing are tested under different test conditions (such as foil gas dynamic pressure radial bearing size, The test results obtained by rotating shaft speed, ambient air pressure and humidity, etc.) are compared. Since the test conditions can be changed, it can be tested by setting Test conditions to change the static load carrying capacity of the bearing.

The conditions of use of the test methods described in this document are as follows.

a) The steady state is the prerequisite for the evaluation of static load carrying capacity, that is, under certain working conditions, the load magnitude, direction and speed are always the same;

b) The evaluation procedure can only be entered when the foil gas dynamic pressure radial bearing maintains the moment of inertia at a certain speed;

c) The dynamic load with time-varying amplitude and time-varying direction is not considered.

2 Normative references

There are no normative references in this document.

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Takeoff

The gas dynamic pressure between the rotating shaft and the top foil ensures that the rotating shaft and the top foil begin to separate a certain distance during the operation phase.

3.2 Clearance

The minimum distance between the shaft and the top foil when the geometric center of the shaft coincides with the geometric center of the sleeve.

3.3 Bearing torque

The friction torque between the rotating shaft and the top foil due to friction caused by rotation.

Note: Refer to 6.4 for bearing friction torque test.

3.4 Load loadcapacity

The load that the bearing can withstand under static conditions.

3.5 Initial load

The load (3.4) applied to the rotating system at the initial stage.

Note: The initial load should be less than the static load capacity and the load used to determine the bearing life, see 7.3 and 10.2.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

How to Download GB/T 40116-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 40116-2021

$285.00