GB/T 39687-2020Testing method for drying loss of fine ceramic powders (English PDF)
精细陶瓷粉体干燥损失测试方法
This is a limited preview
Buy now to download the full PDF (13 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39687-2020 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
December 14, 2020
Implementation date
July 1, 2021
Scope
GB/T 39687-2020 is the English-translated version of 精细陶瓷粉体干燥损失测试方法.
GB/T 39687-2020 — This standard specifies the principle, test equipment, sample preparation, test procedures, and results of the drying loss test method for granular fine ceramic powder Calculation, arbitration test method and test report: This standard is applicable to the determination of the drying loss of granular fine ceramic powder, and the determination of the drying loss of other inorganic non-metallic powders: Can refer to implementation:
Found what you need?
Document preview — GB/T 39687-2020
National Standard of the People's Republic of China
- ICS
- 81.040.10
- Classification
- Q 32
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Principle
- 3 Test device
- 4 Sample preparation
- 5 Test procedure
Foreword
This standard was drafted in accordance with the rules given in GB/T 1:1-2009:
This standard uses the redrafting method to amend and adopt ISO 17860:2014 "Fine Ceramics (Advanced Ceramics, Advanced Technical Ceramics) Ceramic Micro
Determination of loss on drying of grains":
Compared with ISO 17860:2014, this standard has many structural adjustments: Appendix A lists this standard and ISO 17860:2014
The chapter number comparison list:
Compared with ISO 17860:2014, this standard has technical differences, and the clauses involved in these differences have been
The set vertical single line (|) is marked, and a list of the corresponding technical differences and their reasons is given in Appendix B:
This standard also made the following editorial changes:
---The standard name was revised to: "Test Method for Drying Loss of Fine Ceramic Powder";
---Informative Appendix A and Appendix B have been added:
This standard was proposed by the China Building Materials Federation:
This standard is under the jurisdiction of the National Industrial Ceramics Standardization Technical Committee (SAC/TC194):
Drafting organizations of this standard: Shandong Industrial Ceramics Research and Design Institute Co:, Ltd:, Shenzhen Shenzhongyuan Technology Co:, Ltd:, China Building Materials Inspection
Certification Group Zibo Co:, Ltd:
1 Scope
This standard specifies the principle, test equipment, sample preparation, test procedures, and results of the drying loss test method for granular fine ceramic powder
Calculation, arbitration test method and test report:
This standard is applicable to the determination of the drying loss of granular fine ceramic powder, and the determination of the drying loss of other inorganic non-metallic powders:
Can refer to implementation:
2 Principle
The granular ceramic powder may contain water, flux, organic additives and other volatile substances: After drying at high temperature, the water and melt in the powder
Agents and organic additives are removed from the granular powder to a certain extent, resulting in a certain quality loss after drying under certain conditions: powder
The mass loss of the powder is divided by the initial mass of the powder before drying, and the percentage obtained is the drying loss of the powder:
3 Test device
3:1 Oven
The accuracy is +/-5°C:
3:2 Flat chassis
Made of metal (such as tin or aluminum) with good thermal conductivity, with a diameter of about 50mm and a height of 30mm:
3:3 Balance
The range is not less than 10g, and the accuracy is 0:001g:
3:4 Dryer
A dryer equipped with desiccant (such as silica gel, anhydrous calcium chloride):
3:5 Moisture Analyzer
The accuracy is 0:001g, with halogen or infrared heating source:
4 Sample preparation
4:1 When sampling, a sampler should be used or an equivalent method should be used to select representative samples from three different locations:
4:2 The sample should be tested in the initial state, if the sample is pretreated, it should be recorded in the report:
5 Test procedure
5:1 Oven method
5:1:1 Set the oven temperature to 110°C, put the empty flat bottom plate into the oven for drying, and the drying time is not less than 2h, then take it out and place it in a dry
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 13 pages — is available in the English PDF.
How to Download GB/T 39687-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 39687-2020
$105.00