GB/T 39482.1-2023Electrochemical impedance spectroscopy(EIS) on coated and uncoated metallic specimens - Part 1: Terms and definitions (English PDF)
涂漆和未涂漆金属试样的电化学阻抗谱(EIS) 第1部分:术语和定义
This is a limited preview
Buy now to download the full PDF (23 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39482.1-2023 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
September 7, 2023
Implementation date
April 1, 2024
Scope
GB/T 39482.1-2023 is the English-translated version of 涂漆和未涂漆金属试样的电化学阻抗谱(EIS) 第1部分:术语和定义.
GB/T 39482.1-2023 is Part 1 of the Chinese national standard series on electrochemical impedance spectroscopy, or EIS, applied to coated and uncoated metallic specimens, and it carries the terms and definitions.
It defines the terms and definitions used for electrochemical impedance spectroscopy in the other parts of GB/T 39482. It has no normative references.
The vocabulary of clause 3 runs from peak-to-peak amplitude, given the symbol 2U0 and defined as the maximum difference between the maximum and the minimum of the applied alternating disturbance signal, through root mean square amplitude with the symbol Urms, the Bode plot with its curve of phase angle against the logarithm of the applied frequency and its curve of the logarithm of the impedance magnitude against the same, charge transfer resistance with the symbol Rct, and coating, taken from ISO 4618:2014.
The series is intended to run to four parts, of which Part 1 on terms and definitions and Part 3 on the processing and analysis of the data obtained from a dummy cell have been published.
It is the equivalent of ISO 16773-1:2016, to which a normative references clause and an index have been added. It was issued on 7 September 2023 and has applied since 1 April 2024.
Found what you need?
Document preview — GB/T 39482.1-2023
National Standard of the People's Republic of China
- ICS
- 87.010
- Classification
- G 50
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Normative reference documents
- 3 Terms and definitions
Foreword
This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents" Drafting.
This document is Part 1 of GB/T 39482 "Electrochemical Impedance Spectroscopy (EIS) of Painted and Unpainted Metal Specimens". GB/T 39482 The following sections have been published.
---Part 1: Terms and definitions;
---Part 3: Processing and analysis of data obtained from simulated electrolytic cells.
This document is equivalent to ISO 16773-1:2016 "Electrochemical impedance spectroscopy (EIS) of painted and unpainted metal specimens - Part 1: Techniques" Phrases and Definitions.
This document adds a chapter "Normative References" and an "Index".
Introduction
GB/T 39482 describes the application of electrochemical impedance spectroscopy (EIS). Although this document was originally developed for coatings and is primarily Parts are for coatings, but general guidelines can also be applied to unpainted specimens. For unpainted specimens, the ISO / More information is found in TR16208.
GB/T 39482 aims to describe the application of electrochemical impedance spectroscopy (EIS) and is intended to consist of four parts.
---Part 1: Terms and definitions. Terms and definitions used in electrochemical impedance spectroscopy are defined.
---Part 2: Data collection. Describes an experimental procedure for testing laboratory instruments for acquisition and presentation under potentiostatic control The following collection focuses on EIS data of high-resistance organic coatings on metal surfaces. Specifies simulations for simulating the characteristics of high-impedance systems Cell. Test procedures and setup parameters for collecting impedance data from simulated electrolytic cells and coated metal specimens are given. number. A procedure is outlined for comparing recorded spectra using theoretical data from a simulated electrolytic cell in order to establish an acceptable Guidelines for developing instrument precision and limitations. No guidance on data interpretation is provided.
---Part 3: Processing and analysis of data obtained from simulated electrolytic cells. Specifies a method for evaluating high-resistance painted specimens Procedures for the EIS test device, and acceptance criteria for the obtained values are given.
---Part 4: Examples of spectra for coated and uncoated polymer samples. Is informative in nature and includes the resistance of coated metal specimens Some background on antispectral studies and some typical spectrum examples of actual coatings.
ISO /T R16208 describes the basic principles of electrochemical impedance spectroscopy (EIS), with a particular focus on corrosion of metallic materials. It also involves how Use electrochemical equipment, set up and connect electrical instruments, display measurement data, and analyze results.
1 Scope
This document defines the terms and definitions used in electrochemical impedance spectroscopy (EIS) in other parts of GB/T 39482.
2 Normative reference documents
This document has no normative references.
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 Peak-to-peak amplitude
2U0 The maximum difference between the maximum and minimum excitation signals in the applied AC disturbance signal.
Note: Peak-to-peak amplitude is usually expressed in millivolts (mV).
3.2 Root mean square amplitude rms amplitude
Urms The root mean square (i.e. effective) value of the applied AC disturbance signal.
Note: That is the peak-to-peak value of AC amplitude divided by (2×2).
3.3 Bode plot
The relationship curve (a) between the phase angle (3.36) and the logarithm of the applied frequency, and the logarithm of the impedance magnitude (3.28) |Z| and the logarithm of the applied frequency Relationship curve (b).
3.4 Charge transfer resistance; Rct
The resistance of a resistor that represents the properties of the metal-electrolyte interface in the equivalent circuit (3.18).
Note: Charge transfer resistance is usually expressed in ohms (ohm). Charge transfer resistivity is usually expressed in ohms square centimeters (ohm·cm2).
3.5 Coating
A layer of paint applied to a substrate in one or more applications. [Source: ISO 4618:2014,2.50.1]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.
How to Download GB/T 39482.1-2023
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 39482.3-2020 — Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 3: Processing and analysis of data from dummy cells
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 39482.1-2023
$215.00