GB/T 39249-2020Rubber and plastics hoses and tubing. Textile-reinforced types. Sub-ambient temperature crush test (English PDF)
橡胶和塑料软管及非增强软管 织物增强型 低温压扁试验
This is a limited preview
Buy now to download the full PDF (9 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39249-2020 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
November 19, 2020
Implementation date
October 1, 2021
Scope
GB/T 39249-2020 is the English-translated version of 橡胶和塑料软管及非增强软管 织物增强型 低温压扁试验.
GB/T 39249-2020 — This standard specifies the test for determining the low-temperature brittleness of fabric-reinforced rubber and plastic hoses and non-reinforced hoses by flattening hose samples.
This standard only applies to hoses with a nominal inner diameter less than or equal to 100mm.
Found what you need?
Document preview — GB/T 39249-2020
National Standard of the People's Republic of China
- ICS
- 23.040.70
- Classification
- G 42
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Principle
- 4 devices
- 4.2 Conditioning room. It can maintain the specific temperature selected in Chapter 6.
- 5 Sample
- 6 Test temperature
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the translation method equivalent to ISO 28702.2008 "Rubber and plastic hoses and non-reinforced hose fabric reinforced low temperature
Flattening test.
The Chinese documents that have a consistent correspondence with the international documents cited in this standard are as follows.
---GB/T 2941-2006 Rubber Physical Test Method General Procedure for Sample Preparation and Adjustment (ISO 23529.2004, IDT).
This standard was proposed by the China Petroleum and Chemical Industry Federation.
This standard is under the jurisdiction of the National Rubber and Rubber Products Standardization Technical Committee (SAC/TC35).
Drafting organizations of this standard. Ruiyuan Rubber Products Co., Ltd., Shenyang Rubber Research and Design Institute Co., Ltd.
1 Scope
This standard specifies the test for determining the low-temperature brittleness of fabric-reinforced rubber and plastic hoses and non-reinforced hoses by flattening hose samples.
This standard only applies to hoses with a nominal inner diameter less than or equal to 100mm.
2 Normative references
The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this document.
For undated references, the latest version (including all amendments) applies to this document.
ISO 23529 Rubber Physical Test Methods General Procedures for Sample Preparation and Adjustment
3 Principle
Flatten a hose sample to 50% of its inner diameter at the test temperature, and after the pressure is relieved, check whether there are cracks or other
unusual phenomenon.
4 devices
4.1 Compression fixture or other appropriate device. consists of two large enough flat plates, which can squash the hose to 50% of its inner diameter.
4.2 Conditioning room. It can maintain the specific temperature selected in Chapter 6.
5 Sample
Take a circular sample of about 25mm from the hose to be tested.
6 Test temperature
The test should be carried out at one of the following temperatures or the low temperature specified by other relevant product standards.
---0 degrees C+/-2 degrees C;
----10 degrees C+/-2 degrees C;
----25 degrees C+/-2 degrees C;
----40 degrees C+/-2 degrees C;
----55 degrees C+/-2 degrees C.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.
Referenced standards
Normative references
ISO 23529
How to Download GB/T 39249-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 39249-2020
$75.00