GB/T 39181-2020Consumer products—Polyester fiber and ABS material—Rapid determination method of fragrance allergens (English PDF)
消费品 聚酯纤维及ABS材质 致敏性芳香剂快速检测方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39181-2020 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 21, 2020
Implementation date
October 21, 2020
Scope
GB/T 39181-2020 is the English-translated version of 消费品 聚酯纤维及ABS材质 致敏性芳香剂快速检测方法.
GB/T 39181-2020 is the Chinese standard "Consumer products - Polyester fiber and ABS material - Rapid determination method of fragrance allergens".
Its scope clause reads: This Standard specifies the determination method of headspace gas chromatography-mass spectrometry for 54 kinds of fragrance allergens in consumer product polyester fiber and acrylonitrile-butadiene-styrene (ABS) material.
This Standard applies to the rapid determination of the content of 54 kinds of fragrance allergens in consumer product polyester fiber and ABS material. Its clauses include principle; reagents or materials; apparatus; samples; analytical procedure; data processing; method quantification limit; recovery rate and precision; test report.
It was issued by the State Administration for Market Regulation on OCTOBER 21, 2020 and took effect on OCTOBER 21, 2020.
Found what you need?
Document preview — GB/T 39181-2020
National Standard of the People's Republic of China
- ICS
- 13.120
- Classification
- Y 41
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Principle4
- 3 Reagents or materials4
- 4 Apparatus5
- 5 Samples5
- 6 Analytical procedure6
- 7 Data processing8
- 8 Method quantification limit9
- 9 Recovery rate and precision9
- 10 Test report10
- Appendix A (Normative) Analysis parameters of 54 fragrance materials11
- Appendix B (Informative) Total ion chromatogram of 54 fragrance materials13
- Appendix C (Informative) Statistical data of precision test obtained from laboratory14
1 Scope
This Standard specifies the determination method of headspace gas chromatography-mass spectrometry for 54 kinds of fragrance allergens in consumer product polyester fiber and acrylonitrile-butadiene-styrene (ABS) material.
This Standard applies to the rapid determination of the content of 54 kinds of fragrance allergens in consumer product polyester fiber and ABS material.
2 Principle
CUT the polyester fiber into a headspace bottle; ADD a small amount of organic solvent. After crushing the ABS, use solvent dissolution-precipitation method to extract; PLACE the extracted trace solution into the headspace bottle. SET the headspace parameters. The fragrance in the sample volatilizes and quickly forms a dynamic equilibrium in the bottle (polyester fiber sample); or all is transferred to the headspace (ABS sample). At this time, the concentration of the fragrance in the headspace gas is proportional to its initial content in the sample. Introduce the headspace gas to the gas chromatograph-mass spectrometer for determination. By measuring the concentration of fragrances in the headspace gas, the content of fragrances in the sample can be obtained.
3 Reagents or materials
3.1 Acetone: Chromatographically pure.
3.2 Methanol: Chromatographically pure.
3.3 Fragrance reference materials: The purity is all greater than 90%. The material types are shown in Appendix A.
3.4 Single standard stock solution: Respectively weigh the appropriate amount of fragrance reference materials (3.3) accurately; USE acetone to prepare a single standard solution of appropriate concentration; STORE it in a refrigerator at 4 °C. The expiry date is 12 months. FREEZE and crush the sample to a particle size of less than 1 mm; WEIGH 0.2 g (accurate to 0.1 mg) into a 20 mL glass bottle (4.6). ADD 5 mL of acetone to dissolve; then slowly add 5 mL of methanol while shaking. After the polymer precipitation is complete, take 40 µL of the supernatant and place it in a 20 mL headspace bottle (4.5). Quickly seal the headspace bottle; PLACE it in the headspace autosampler. Under the set headspace conditions, the fragrance is transferred to the gas phase. At this time, the concentration of the fragrance material in the headspace gas is proportional to its initial content in the sample. Introduce the gas in the quantitative loop into a gas chromatograph-mass spectrometer for analysis.
6 Analytical procedure
6.1 Headspace injection conditions
The test results depend on the apparatus used. General parameters for headspace injection cannot be given. The following operating conditions have been proven appropriate:
a) Equilibrium temperature: 180 °C~200 °C. High-temperature-resistant headspace bottle sealing caps and gaskets shall be used; otherwise the gasket may be damaged and leaking or even the bottle cap may burst.
b) Equilibrium time: 10 min (polyester fiber); 6 min (ABS).
c) Auxiliary gas pressurization pressure: 70 kPa (polyester fiber); 80 kPa (ABS).
d) Auxiliary gas pressurization time: 10 s.
e) Quantitative loop temperature: 5 °C~10 °C higher than the equilibrium temperature.
f) Transmission line temperature: 5 °C~10 °C higher than the quantitative loop temperature.
g) Volume of quantitative loop: 1 mL.
h) Equilibrium time of quantitative loop: 10 s.
i) Injection time: 20 s.
6.2 Determination conditions of gas chromatography-mass spectrometry
The test results depend on the apparatus used. General parameters for gas chromatography-mass spectrometry cannot be given. The set parameters shall ensure that, during the determination, the measured component and other components can be effectively separated. The following parameters are available for reference:
a) Chromatographic column: Low-loss quartz capillary column (30 m×0.25 mm×0.25 µm) with a stationary phase of 35% phenyl and 65% dimethyl polysiloxane; or equivalent;
b) Temperature programming: KEEP at 40 °C for 1 min; RAISE to 210 °C at 5 °C/min; then raise to 300 °C at 10 °C/min;
c) Temperature of injection port: 280 °C;
d) Ion source temperature: 230 °C;
e) Transmission line temperature: 280 °C;
f) Carrier gas: Helium (purity>=99.999%). Flow rate is 1.0 mL/min;
g) Ionization method: EI ionization;
h) Ionization energy: 70 eV;
i) Injection mode: Split injection. Split ratio is 10:1;
j) Data acquisition mode: Selected ion monitoring (SIM). The analysis parameters of each material are shown in Appendix A;
k) Solvent delay: 2.5 min.
6.3 Drawing of standard curve
6.3.1 Polyester fiber
ADD 20 µL of standard working solution (3.6) to the headspace bottle (4.5) containing the blank sample of polyester fiber. Quickly press the bottle cap to prepare a series of standard samples with different fragrance content. Then, the standard samples are determined in order from low to high concentration.
USE the peak area of the quantitative ion chromatographic peak as the ordinate; USE the corresponding fragrance mass (in micrograms) as the abscissa;
DRAW the standard working curve. For the total ion chromatogram of 54 fragrance materials under the above analysis conditions, refer to Appendix B.
6.3.2 ABS
ADD 40 µL of standard working solution (3.6) to the headspace bottle (4.5).
Quickly press the bottle cap to prepare a series of standard samples with […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 39181-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 39181-2020
$185.00