GB/T 39169-2020Blanks for diamond circular saw blade - Mounting and fixing bores - Building construction and civil engineering (English PDF)
金刚石圆锯片基体 安装和固定孔 建筑施工和土木工程
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39169-2020 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
October 11, 2020
Implementation date
May 1, 2021
Scope
GB/T 39169-2020 is the English-translated version of 金刚石圆锯片基体 安装和固定孔 建筑施工和土木工程.
GB/T 39169-2020 — This standard specifies the type, size and mark of the mounting and fixing holes of the diamond circular saw blade base. This standard applies to the installation and fixing holes of the diamond circular saw blade substrate for construction and civil engineering.
Found what you need?
Document preview — GB/T 39169-2020
National Standard of the People's Republic of China
- ICS
- 25.100.70
- Classification
- J 43
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Type and size
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the redrafting method to modify and adopt ISO 21538.2016 ``Super-abrasive cutting wheel substrate installation and fixed hole construction
Construction and Civil Engineering.
Compared with ISO 21538.2016, there are technical differences between this standard and the clauses involved in these differences have been passed on the outer margins.
The set vertical single line (︱) is marked, and a list of the corresponding technical differences and their reasons is given in Appendix A.
This standard also made the following editorial changes.
---Modified the standard name.
This standard was proposed by China Machinery Industry Federation.
This standard is under the jurisdiction of the National Abrasives Standardization Technical Committee (SAC/TC139).
Drafting organizations of this standard. Zhengzhou Abrasives Grinding Research Institute Co., Ltd., Heixuanfeng Saw Industry Co., Ltd., Beijing Antai Steel Research Super
Hard Material Products Co., Ltd., Boshen Co., Ltd., Guangdong Benlang New Materials Co., Ltd., Quanzhou Wanlong Stone Industry Co., Ltd., Fujian Province
Limited company, Quanzhou Zhongzhi New Material Technology Co., Ltd.
1 Scope
This standard specifies the type, size and mark of the mounting and fixing holes of the diamond circular saw blade base.
This standard applies to the installation and fixing holes of the diamond circular saw blade substrate for construction and civil engineering.
2 Normative references
The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this document. For undated references, the latest version (including all amendments) applies to this document.
GB/T 1804 General tolerance The tolerance of linear and angular dimensions without tolerance (GB/T 1804-2000, eqvISO 2768-1.1989)
GB/T 39140.2 Clamping chuck for diamond circular saw blade Part 2.Construction and civil engineering (GB/T 39140.2-2020, ISO 21537-2..2004, MOD)
3 Type and size
There are 5 types of mounting and fixing holes for the diamond circular saw blade base. only the center hole (Type A), and there is a drive pin hole outside the center hole (B
Type), there are up to 2 sets of ring-shaped drive pin holes (C type) outside the center hole, and up to 2 sets of ring-shaped mounting holes (D type) outside the center hole.
There is a drive pin hole and a group of ring-shaped mounting holes (E type) outside the hole, as shown in Figure 1 to Figure 5, and their dimensions are shown in Table 1 to Table 5.
The dimensions of these mounting and fixing holes are consistent with the relevant dimensions of the clamping chuck specified in GB/T 39140.2.
Other requirements not specified should be selected according to needs.
Figure 1 Type A mounting and fixing holes
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 1804General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
- GB/T 1804-2000General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
- GB/T 39140.2Clamping flanges for diamond circular saw blade - Part 2: Building construction and civil engineering
- GB/T 39140.2-2020Clamping flanges for diamond circular saw blade - Part 2: Building construction and civil engineering
ISO 21537
How to Download GB/T 39169-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 1804-1992 — General tolerances. Tolerances for linear dimensions without individual tolerance indications
GB/T 1804-2000 — General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
GB/T 39140.2-2020 — Clamping flanges for diamond circular saw blade - Part 2: Building construction and civil engineering
GB/T 39169-2020
$150.00