Valid

GB/T 39144-2020Test method for magnesium content in gallium nitride materials—Secondary ion mass spectrometry (English PDF)

氮化镓材料中镁含量的测定 二次离子质谱法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 39144-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 11, 2020

Implementation date

September 1, 2021

Scope

GB/T 39144-2020 is the English-translated version of 氮化镓材料中镁含量的测定 二次离子质谱法.

GB/T 39144-2020 is the Chinese standard "Test method for magnesium content in gallium nitride materials—Secondary ion mass spectrometry". Its scope clause reads: This standard specifies the secondary ion mass spectrometry test method for magnesium content in gallium nitride materials.

This standard applies to the quantitative analysis of magnesium content in gallium nitride materials, and the measurement range is not less than 5×1014cm-3. Note.

The magnesium content in gallium nitride material is calculated by the number of atoms per cubic centimeter. Its clauses include terms and definitions; principle of the method; disturbing factors.

Found what you need?

Document preview — GB/T 39144-2020

National Standard of the People's Republic of China

ICS
77.040
Classification
H 17

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Principle of the method
  • 5 Disturbing factors

1 Scope

This standard specifies the secondary ion mass spectrometry test method for magnesium content in gallium nitride materials.

This standard applies to the quantitative analysis of magnesium content in gallium nitride materials, and the measurement range is not less than 5×1014cm-3.

Note. The magnesium content in gallium nitride material is calculated by the number of atoms per cubic centimeter.

2 Normative references

The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this document.

For undated references, the latest version (including all amendments) applies to this document.

GB/T 14264 Terminology of Semiconductor Materials

GB/T 22461 Surface Chemical Analysis Vocabulary

GB/T 32267 Analytical Instrument Performance Measurement Terms

3 Terms and definitions

The terms and definitions defined in GB/T 14264, GB/T 22461 and GB/T 32267 apply to this document.

4 Principle of the method

Under the condition of high vacuum (vacuum degree is better than 10-6Pa), the primary ions generated by the oxygen ion source will bombard the nitrogen after being accelerated, purified and focused.

A variety of particles were sputtered on the surface of gallium sulfide sample. Extract the ions (i.e. secondary ions) and separate the ions with different mass-to-charge ratios through a mass spectrometer.

Record and calculate the ratio of the ion count rate of magnesium to gallium in the sample, and use the relative sensitivity factor to quantitatively analyze and calculate the magnesium content in the gallium nitride material.

5 Disturbing factors

5.1

The secondary ion mass spectrometer has a memory effect. If a sample with a higher magnesium content is tested, a high content of magnesium will remain in the sample chamber of the instrument, which will affect the test result of the magnesium content.

5.2

Different instrument models or different states of the same instrument (e.g. electron multiplier efficiency, aperture size, primary beam size, focus state

State, etc.), will affect the detection limit of this method.

5.3

The sample analysis surface within the sample rack window should be flat to ensure that when each sample moves to the analysis position, its surface and ion collection

The tilt of the optical system remains unchanged, otherwise the accuracy of the test will be reduced.

5.4

Magnesium ions adsorbed on the sample surface may affect the test results of magnesium content.

5.5

The accuracy of the test decreases significantly as the surface roughness of the sample increases. It should be done by chemical mechanical polishing or chemical

Corrosion polishing reduces surface roughness.

5.6

The non-uniformity of magnesium content in the standard sample will limit the accuracy of the test results.

5.7

Deviations in the nominal content of magnesium in the standard samples will lead to deviations in the test results.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 39144-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 39144-2020

$90.00