Valid

GB/T 39042-2020Measurement of the magnetic properties of electrical steels by means of a single sheet tester—H-coil method (English PDF)

电工钢单片磁性能测试 H线圈法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 39042-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

July 21, 2020

Implementation date

February 1, 2021

Scope

GB/T 39042-2020 is the English-translated version of 电工钢单片磁性能测试 H线圈法.

GB/T 39042-2020 is the Chinese standard "Measurement of the magnetic properties of electrical steels by means of a single sheet tester—H-coil method".

Its scope clause reads: This standard specifies that under power frequency conditions, the H coil is used to measure the magnetic field strength of a single piece of electrical steel strip (slice), and pass the single piece of magnetic Conductometer test method of electrical steel specific total loss, magnetic polarization intensity and specific apparent power.

This standard applies to the detection of the magnetic properties of monolithic samples of grain-oriented or non-oriented electrical steel strips (sheets). Its clauses include terms and definitions; measuring principle; measuring device.

Found what you need?

Document preview — GB/T 39042-2020

National Standard of the People's Republic of China

ICS
77.040.99
Classification
H 21

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Measuring principle
  • 5 Measuring device
  • 5.1 General
  • 5.2 Magnetic yoke
  • 5.3 Coil
  • 5.4 Power supply
  • 5.5 Digital Control System
  • 6 Sample
  • 7 measurement
  • 7.1 Preparation for measurement
  • 7.2 Measurement of magnetic polarization
  • 7.3 Measurement of magnetic field strength
  • 7.4 Measurement of specific total loss
  • 7.5 Measurement of specific apparent power
  • 8 Test results and reproducibility
  • 9 Test report
  • Appendix A (informative appendix) Digital sampling technology for measuring magnetic properties

1 Scope

This standard specifies that under power frequency conditions, the H coil is used to measure the magnetic field strength of a single piece of electrical steel strip (slice), and pass the single piece of magnetic

Conductometer test method of electrical steel specific total loss, magnetic polarization intensity and specific apparent power.

This standard applies to the detection of the magnetic properties of monolithic samples of grain-oriented or non-oriented electrical steel strips (sheets).

2 Normative references

The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

GB/T 2900.60 Electrotechnical terminology electromagnetics

GB/T 3102.5 Quantities and units of electricity and magnetism

GB/T 9637 Electrical Engineering Terminology Magnetic Materials and Components

GB/T 13789 Method for measuring the magnetic properties of electrical steel sheets (bands) with a monolithic tester

GB/T 19289 Method for measuring electrical resistivity, density and stacking coefficient of electrical steel strip (sheet)

3 Terms and definitions

The following terms and definitions defined in GB/T 2900.60, GB/T 3102.5, and GB/T 9637 apply to this document.

3.1 H coil

An air-core coil placed near the surface of the sample to directly detect the true magnetic field strength of the sample.

4 Measuring principle

The sample and the yoke form a closed magnetic field loop, and the intensity of the magnetic field passing through the sample is obtained by detecting the induced voltage on the H coil.

The magnetic polarization intensity is obtained by the induced voltage of the B coil (inductive voltage coil, also called the secondary coil), and the magnetic properties of the sample can be measured.

5 Measuring device

5.1 General

The electrical steel sample is placed in the middle of the coil frame, the coil frame is wound with two layers of coils, and the outside is the excitation coil (also called the primary coil).

The inside is a B coil, and a set of H coils are placed on the coil bobbin near the lower surface of the sample, as shown in Figure 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 39042-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 39042-2020

$240.00