Valid

GB/T 38535-2020Test method on fiber reinforced resin matrix composites by industrial computed tomography (CT) (English PDF)

纤维增强树脂基复合材料工业计算机层析成像(CT)检测方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 38535-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

March 6, 2020

Implementation date

February 1, 2021

Scope

GB/T 38535-2020 is the English-translated version of 纤维增强树脂基复合材料工业计算机层析成像(CT)检测方法.

GB/T 38535-2020 is the Chinese standard "Test method on fiber reinforced resin matrix composites by industrial computed tomography (CT)". Its scope clause reads: This standard specifies the detection principles, general requirements, and inspection requirements for computer tomography (CT) testing of fiber-reinforced resin-based composite materials.

Test systems, comparative samples, test procedures, results evaluation, records and reports. This standard applies to industrial computer tomography of internal defects such as delamination, cracks, pores, and inclusions in fiber-reinforced resin-based composites.

(Hereinafter referred to as industrial CT) detection. Its clauses include detection principle; general requirements.

Found what you need?

Document preview — GB/T 38535-2020

National Standard of the People's Republic of China

ICS
83.120
Classification
Q 23

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Detection principle
  • 4 General requirements

1 Scope

This standard specifies the detection principles, general requirements, and inspection requirements for computer tomography (CT) testing of fiber-reinforced resin-based composite materials.

Test systems, comparative samples, test procedures, results evaluation, records and reports.

This standard applies to industrial computer tomography of internal defects such as delamination, cracks, pores, and inclusions in fiber-reinforced resin-based composites.

(Hereinafter referred to as industrial CT) detection.

2 Normative references

The following documents are essential for the application of this document. For dated references, only the dated version applies to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

GB 18871 Basic standards for ionizing radiation protection and radiation source safety

GB/T 29069 Non-destructive testing method for industrial computer tomography (CT) system performance test

GB/T 29070 General requirements for non-destructive testing industrial computer tomography (CT) testing

GBZ 98 Health Requirements for Radiation Workers

GBZ 117 Radiological protection requirements for industrial X-ray inspection

3 Detection principle

X-ray transillumination of a certain section of the inspected object, the energy attenuation occurs, the radiation attenuation information is collected by the detector, and the attenuation information is input to the computer

A computer uses an image reconstruction algorithm to obtain a two-dimensional or three-dimensional image of the inspected part after transmission.

4 General requirements

4.1 Testing personnel

4.1.1

Personnel engaged in industrial CT testing of fiber-reinforced resin-based composite materials shall obtain corresponding technical qualification certificates.

4.1.2

The health status of the testing personnel shall comply with the provisions of GBZ 98, and undergo radiation protection knowledge training to obtain a qualification certificate.

4.1.3

The inspector should wear a personal dosimeter at work. The personal dosimeter should be sent to the relevant departments for testing on a regular basis.

The dose limit should meet the requirements of GB 18871.

4.2 Detection environment

4.2.1

The safety requirements for radiation protection in the testing room shall comply with the regulations in GBZ 117 and GB 18871.

4.2.2

Detection room temperature is 10 °C ~ 35 °C, and relative humidity is less than 85%.

4.2.3

Ventilation, lighting and other environmental conditions shall comply with the provisions in GB/T 29070.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 38535-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 38535-2020

$240.00